[ Log In ]
[ Register ]

Question #: 5767

Question: What are the dimensions of the 24v 8.3A power supply?

Current Solution

The dimensions for our power supplies will be the same.

Dimensions:
L: 8.5" / 215.9mm
W: 4.5" / 114.3mm
H: 2" / 50.8mm

Respond:

Other Possible Solutions to this Question

  • WHAT ARE THE SHIPPING DIMENSIONS FOR VERTICAL LASER

    Shipping crate size 121" X 36" X 92"

    Weight 511 LBS

    Click the link to add information to this solution:
    WHAT ARE THE SHIPPING DIMENSIONS FOR VERTICAL LASER

  • WHAT ARE THE BLACKTOOTH SHIPPING DIMENSIONS?

    The blacktooth ships in 3 boxes.

    Structure 38x22x5 #54

    Components 14x13x13 #30

    Laser Tube 35x7x6 #4

    Click the link to add information to this solution:
    WHAT ARE THE BLACKTOOTH SHIPPING DIMENSIONS?

  • WHAT ARE THE DIMENSIONS FOR GREENBULL TABLE?

    Actual table dimension: 4'x8' is 56.078"x 121.50" (the overhang in the illustrations should be 3/4" thick)
    To determine the frame dimensions, first consider using the frame height shown of almost 3' (2.86'). The width of the frame should be 4" narrower than the dimension from rail edge to rail edge (6X rail to rail is 80.078"). This will provide a 2" overhang on both sides (4X frame width should be 56.078").
    The length of the frame should be 4" shorter than the desired length of the rails to provide a 2" overhang on both ends. The travel length will be 20" shorter than the rail length due to the space occupied by the gantry sides.
    Two long pieces of 3/4" material will need to be placed on top of the frame with the 2" overhang on the sides and the end. These long strips of material will receive the rails and the chain mounts on the ends.


    Link:
    https://www.buildyourcnc.com/Item/cnc-machine-greenBull-v4-4X

    Click the link to add information to this solution:
    WHAT ARE THE DIMENSIONS FOR GREENBULL TABLE?

  • WHAT IS THE SHIPPING WEIGHT AND DIMENSIONS FOR GREENLEAN?

    Shipping crate 121" X 36" X 92"

    Weight 511 LBS

    Additional Information:
    ship in india pls

    Additional Information:
    International shipping rates can be determined by:
    - adding products to the cart
    - go to the cart and enter shipped by address
    - and pressing the calculate shipping button

    Click the link to add information to this solution:
    WHAT IS THE SHIPPING WEIGHT AND DIMENSIONS FOR GREENLEAN?

  • WHAT IS SHIPPING DIMENSIONS AND WEIGHT FOR THE VERTICAL LASER.

    Shipping crate size 121" X 36" X 92"

    Weight 511 LBS

    Click the link to add information to this solution:
    WHAT IS SHIPPING DIMENSIONS AND WEIGHT FOR THE VERTICAL LASER.

  • Can I power the Mach3 USB interface 24V with a 48V power supply?

    The Mach3 USB interface card uses 5V (powered from the computer's USB) and a 24v to power the inputs, outputs and spindle control

    the mach3 usb interface can be found here:

    https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

    But the mach3 usb does not absolutely need the 24V supply. The 24v supply is only needed if you will be using limit switches (I1-4), VFD controlled automatically and for use with the outputs (O1-4)


    Additional Information:
    The 36v 8.8 amp power supply we typically recommend is for powering the stepper motor drivers.

    Click the link to add information to this solution:
    Can I power the Mach3 USB interface 24V with a 48V power supply?

  • What functionality is lost if 24V power supply not provided to "Mach3 USB Motion Card"?

    If the Mach3 USB does not have a 24V power on the limit switch/output/DAC side of the board, then those functions (limit switches, outputs and the DAC) will not work. If you have a spindle, you can use the 24V output from the VFD (Variable Frequency Drive) to serve as the 24V supply.

    Click the link to add information to this solution:
    What functionality is lost if 24V power supply not provided to "Mach3 USB Motion Card"?

  • HOW TO KNOW IF THE POWER SUPPLY OF THE LASER TUBE IS DAMAGED

    This video will illustrate how to test for laser power:

    Click the link to add information to this solution:
    HOW TO KNOW IF THE POWER SUPPLY OF THE LASER TUBE IS DAMAGED

  • [797] Should I use a 24V power supply for this relay?

    The dual 24VDC relay can use any 24V power supply that outputs 24V DC. A great power supply that will work well with this dual 24VDC relay is this power supply: https://buildyourcnc.com/item/electronicsAndMotors-power-supply-24v-1a-dc

    Click the link to add information to this solution:
    [797] Should I use a 24V power supply for this relay?

  • AND WHAT SIZES ARE THE PACKAGES OF MACHINE.

    the package sizes will be listed in your shopping cart, in the item detail. The site will also fully calculate shipping charges directly from the carrier, for each package you purchase.

    Additional Information:

    Click the link to add information to this solution:
    AND WHAT SIZES ARE THE PACKAGES OF MACHINE.

  • WHAT ARE THE HEALTH RISKS OF LIVING NEAR A CELL PHONE TOWER?

    There is very little radiofrequency (RF) energy exposure to people inside a building from a cellular base station located on its roof. There are several reasons for this. First, the transmitters operate at low power levels. Second, the antennas are normally mounted near the edges of the roof and are aimed away from the building. Third, most cellular transmitters use "high gain" or panel antennas. Such antennas transmit most of their energy in a narrow beam (in the vertical direction) from their front surfaces, away from the building. They radiate very little energy downwards towards the roof or backwards from their rear surfaces. Finally, building materials absorb a significant fraction of the RF energy passing through them. As a result, the RF signal levels at any location inside the building are invariably low and far below safety limits. The situation might be different in some locations on the roof itself. RF signal levels close to (within a few feet) and directly in front of cellular base station antennas can easily exceed safety limits. Some precautions are needed to prevent people from walking directly in front of the antennas while they are transmitting. This applies also to paging and other systems that use rooftop antennas, some of which transmit at higher power levels than many cellular base stations. Kenneth R. Foster, Ph.D.

    Click the link to add information to this solution:
    WHAT ARE THE HEALTH RISKS OF LIVING NEAR A CELL PHONE TOWER?

  • WHAT ARE THE ROLLER CHAIN LENGTHS FOR GREENBULL 4X

    The roller chain lengths for the greenBull 4x is:
    - 13 feet for each side of the X axis (total of 26 feet), and
    - 6 feet for the Y-axis

    Click the link to add information to this solution:
    WHAT ARE THE ROLLER CHAIN LENGTHS FOR GREENBULL 4X

  • DO YOU SUPPLY THE MALE PORTION OF MOTOR CONTROL CABLES WITH REDLEAF?

    Yes and properly soldered.

    Additional Information:
    20

    Click the link to add information to this solution:
    DO YOU SUPPLY THE MALE PORTION OF MOTOR CONTROL CABLES WITH REDLEAF?

  • WHAT CABLE LENGTHS ARE USED FOR THE BLACKTOE

    The motor cables for the blackToe are as follows:

    Total 30 feet

    X - 9
    Y - 10
    Z - 11

    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:

    Click the link to add information to this solution:
    WHAT CABLE LENGTHS ARE USED FOR THE BLACKTOE

  • WIRE GAUGE FOR POWER SUPPLY

    Most of our power supplies allow for a 9 amp current draw.

    For the Neutral, Live and earth ground, wire gauge for that level of current is 14 for relatively short cable lengths. Increase the gauge for longer lengths past 25 feet.

    For the DC 24V output terminals to the drivers, 20 gauge is fine. If the power supply is connecting to only one driver, increase the wire gauge to 14.

    Additional Information:
    What gage wire should I use from motor to driver

    Additional Information:


    Additional Information:

    Click the link to add information to this solution:
    WIRE GAUGE FOR POWER SUPPLY

  • CAN BOOST THE POWER OF MY BLACKTOOTH LASER?

    Upgrade your mirrors to SI coated mirrors, using a HQ ZnSe lens and even pushing up to a beam expander will all boost power. The ideal order of experimenation for lowest cost would be changing out for a higher quality lens labeled HQ ZnSE lens. Next would be SI mirrors, which will absorb less heat and reflect better, the last would be to use a beam expander which expands the beam, reducing the heat signature on the mirrors and makes a tighter focal width.

    Click the link to add information to this solution:
    CAN BOOST THE POWER OF MY BLACKTOOTH LASER?

  • WHAT ARE THE BEST FOODS THAT WILL HELP YOU LOSE WEIGHT?

    Lettuce, or any vegetable. Also drink a cup of water before meals, it'll make you feel fuller.

    Click the link to add information to this solution:
    WHAT ARE THE BEST FOODS THAT WILL HELP YOU LOSE WEIGHT?

  • WHAT ARE THE CABLE LENGTHS FOR BLACKTOE

    The motor cables for the blackToe are as follows:

    Total 30 feet

    X - 9
    Y - 10
    Z - 11

    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:

    Click the link to add information to this solution:
    WHAT ARE THE CABLE LENGTHS FOR BLACKTOE

  • WHAT ARE THE CABLE LENGTHS FOR BLACKTOE

    The motor cables for the blackToe are as follows:

    Total 30 feet

    X - 9
    Y - 10
    Z - 11

    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:

    Click the link to add information to this solution:
    WHAT ARE THE CABLE LENGTHS FOR BLACKTOE

Get Help with:
This Product
Orders
Tech Support
Sales
This Product
Order Query
Tech Support
Sales
Not logged in. Log In Register
Track Order(s)
View Order(s)
I Want to Schecule a One-On-One Paid Tech Support Session
Book an Appointment Pertaining to a BuildYourCNC Product (Free)
Ask a Quesion Below (Free):
Book an Appointment Pertaining Other Equipment ($60/half hour)
Book an Immedite Appointment Pertaining Other Equipment ($120/half hour)
Ask a Quesion Below (Free):
Waiting for response... I may not answer immediately, but I was notified on my cellular phone so my response is forthcoming. If I don't respond immediately, you can always go to the [My Account] page to see all of our chats at any time.