[ Log In ]
[ Register ]
NEW: CNC Router PLANS Available for all of our Newest CNC Models!! Click here to "Design Your CNC".

Question #: 544

Question: WHAT ARE THE BEST FOODS THAT WILL HELP YOU LOSE WEIGHT?

Current Solution

Lettuce, or any vegetable. Also drink a cup of water before meals, it'll make you feel fuller.

Respond:

Other Possible Solutions to this Question

  • Is there any other software that will work with your controller Mach3?

    The mach3 control software will work with all major CAM software (CAMBAM, Aspire and Vectric, BobCAD/CAM, ArtCAM, Dolphin CAM, CAM software that integrate with SolidWorks and AutoDesk Inventor, and many more).

    Click the link to respond:
    Is there any other software that will work with your controller Mach3?

  • Hi what is the maximun weight of a gantry that a Nema 34 651 oz can carry ?

    The holding torque of the NEMA34 motor is rated at 651 oz-in. This is the maximum amount of weight the motor holds in a stationary position while optimal current is being applied through the driver. This is equivalent to 40.68 lbs per inch. Torque is measured from the center of the shaft. The torque applied to the shaft moving 1 inch is inversely proportional. For example: Moving 1/2" on the shaft has a maximum of 1302 oz or moving 2" has a maximum of 325.5 oz.

    Click the link to respond:
    Hi what is the maximun weight of a gantry that a Nema 34 651 oz can carry ?

  • What doesn't come with the electronics that I will need so it will work?

    Here is a list of the parts needed to get the electronics combo functioning (parallel or USB interface options):

    - 22 or 24 gauge stranded hookup wire to connect all of the drivers to the USB or parallel interface (terminal to terminal connections),
    - 18 gauge stranded hookup wire to connect the drivers to the power supply,
    - a power cable (extension cord) to connect from the power outlet to the power supply,
    - 4 conductor cable to connect the drivers to the stepper motors,
    - a USB cable to connect from the computer to the USB interface (or for power to the parallel interface),
    - for the parallel interface, a parallel cable is needed (male to male db-25),
    - a computer (for parallel interface, the computer will need a parallel port and if the computer does not contain a parallel interface, the motherboard may have a header for it, or you can purchase a parallel adapter to plug into the motherboard, very inexpensive),
    - cnc control software: for the USB interface, you will need planet-cnc software, for the parallel interface, you can use any industry standard cnc control software (the typical is Mach3 for Windows, or EMC2 or Linuxcnc for Linux (Linuxcnc.org).

    5v power supply is not needed. The 5 volts signal level power is derived from the computer through USB on both types of interfaces.

    Click the link to respond:
    What doesn't come with the electronics that I will need so it will work?

  • what are the specs of the blacktooth laser cutter (dimensions and weight) when assembled?

    The blackTooth envelope dimensions and weight:

    - Length and width: 37" x 34"
    - The height: 11.25"
    - The weight: 70 lbs.

    Click the link to respond:
    what are the specs of the blacktooth laser cutter (dimensions and weight) when assembled?

  • What size/ kind of rail is the hiwin rail that you sell?

    My apologies for not having the specifications on the product page for our Hiwin rail and block:

    The specifications are as follows (we will add this information to the product page):

    Rail:
    Rail width: 20mm
    Mounting bolt: M5x16
    Mounting hole center to hole center: 60mm

    Guide Block:
    Width of block: 63mm
    Length of block:77.5mm
    Mounting holes distance in the width direction: 53mm
    Mounting holes distance in the length direction: 40mm

    Both:
    From bottom of rail to top of block: 30mm
    From block bottom to bottom of rail (clearance): 4.6mm

    Click the link to respond:
    What size/ kind of rail is the hiwin rail that you sell?

  • Will you guys ship to the UK & what is the estimated time?

    You can determine if the country is serviceable by:
    - selecting the items you want to purchase on the website
    - go to the cart (shopping cart top left of any webpage)
    - log in, or register
    - Enter the address and click on calculate shipping.

    The webpage will return the direct rates and whether your area is serviced or not. Feel free to enter any address as long as you are able to receive the package from that address.

    The shipping times are determined by the service you select in the shopping cart. If a machine is purchased, we generally have a one week lead time unless otherwise stated in the description of the machine's product page.

    Click the link to respond:
    Will you guys ship to the UK & what is the estimated time?

  • What will be the amount of cable carrier that I will need for a greenBull 5x?

    To determine the length of cable carrier you will need for a single axis, measure the axis travel of your machine, divide this by 2 and add 12 inches. The radius of the curl is 2 inches.
    The amount of cable carrier needed for the CNC machines that we provide will be:

    blueChick: Total 4 Ft

    blackToe: Total 5 Ft

    blackFoot: Total 8 Ft

    greenLean: Total 8 Ft

    greenBull 5x: Total 10 Ft

    greenBull 6x: Total 11 Ft

    Click the link to respond:
    What will be the amount of cable carrier that I will need for a greenBull 5x?

  • What are the acceptable materials that I can cut?

    The machines on this site can cut a wide variety of materials. If there is an end mill (cutting bit) that is available on the market, the machine can cut it. The thickness is only limited by the end mill length. This is possible with these CNC machines and other machines on the market because the machines can be controlled in such a way that the material can be cut using depth per pass, feed rate, and spindle RPM.

    Click the link to respond:
    What are the acceptable materials that I can cut?

  • What issues will a user need to be prepared to solve with the vertical laser that they wouldn't normally see with a horizontal bed?

    I personally haven't noticed any issues with horizontal and vertical (slanted). If there is no backing on the vertical laser (something behind the workpiece), then the parts do tend to fall out. Just keep something behind the workpiece.

    On a horizontal bed, you may be able to get a bit of a better vacuum hold down, but with a machine the size of a 4'x8', there really isn't a great way to get vacuum hold down, and I haven't seen the need for it anyway.

    Click the link to respond:
    What issues will a user need to be prepared to solve with the vertical laser that they wouldn't normally see with a horizontal bed?

  • what is Andriy Dzundra's address that we are shipping to in the US?

    The lens is 20mm wide and a 50.6mm focal length (the one included). This lens will stand up to at least 30PSI air assist.

    The mirrors are 25mm wide mirrors.

    Click the link to respond:
    what is Andriy Dzundra's address that we are shipping to in the US?

  • you have asked me a ? that I do not know what you are talking about

    You are just sending a lot off dust

    Additional Information:
    are you able to supply a control board only

    Additional Information:
    Yes.

    Click the link to respond:
    you have asked me a ? that I do not know what you are talking about

  • What are the EN connections used for on the QJ8060 motor driver? I notice that your video seems to leave them unconnected.

    The EN terminal on the QJ8060 driver and all of our other stepping motor drivers is the enable terminal. We don't use this terminal and the driver will function properly if left unconnected.

    Click the link to respond:
    What are the EN connections used for on the QJ8060 motor driver? I notice that your video seems to leave them unconnected.

  • WHAT IS THE SHIPPING WEIGHT AND DIMENSIONS FOR GREENLEAN?

    Shipping crate 121" X 36" X 92"

    Weight 511 LBS

    Additional Information:
    ship in india pls

    Additional Information:
    International shipping rates can be determined by:
    - adding products to the cart
    - go to the cart and enter shipped by address
    - and pressing the calculate shipping button

    Click the link to respond:
    WHAT IS THE SHIPPING WEIGHT AND DIMENSIONS FOR GREENLEAN?

  • What´s the size and weight of the blacktooth shipping box?

    For our blackTooth laser cuter and engraver, the specified packages in shipment may vary to option chosen and additional purchases.

    3 packages:
    40" x 21" x 5"/54 lb.
    17" x 12" x 12"/27 lb.
    40" x 10" x 7"/5 lb.

    Click the link to respond:
    What´s the size and weight of the blacktooth shipping box?

  • What size forstner are used in the book build your own cnc

    That was a very long time ago, but I think I was using 3/4". You can use a size just larger than the outer width of the nut.

    Click the link to respond:
    What size forstner are used in the book build your own cnc

  • What is the cost of the Planet-CNC software? Do you sell it?

    The base price for planet cnc is 69 Euros, which translates to $85.85 dollars. Can be found here (http://www.planet-cnc.com/index.php?page=shop)

    Additional Information:


    Additional Information:

    Click the link to respond:
    What is the cost of the Planet-CNC software? Do you sell it?

  • WHAT IS SHIPPING DIMENSIONS AND WEIGHT FOR THE VERTICAL LASER.

    Shipping crate size 121" X 36" X 92"

    Weight 511 LBS

    Click the link to respond:
    WHAT IS SHIPPING DIMENSIONS AND WEIGHT FOR THE VERTICAL LASER.

  • What output pins on your BOB are used to control the SuperPID?

    Yes, you can use any two of the output terminals of the breakout board to control the SuperPID closed loop router controller (a diagram is not needed with these instructions).

    One output terminal will be used as an on/off (1/0 or 5v/gnd) that will be invoked with the M3/M4/M5 M-codes in your g-code instructions.

    The other terminal will be connected to either another 5v/gnd signal to control speed for 5000/20000 rpm or for PWM output (recommended) for proportional speed control.

    To setup this configuration in Mach3, go to your ports and pins dialog box (config menu -> ports and pins). Click on the spindle setup tab. In the Motor Control Section of the dialog, check the box for Use Spindle Motor Output and check the box for PWM control. Change the PWM Base Frequency to 50Hz.

    Click the link to respond:
    What output pins on your BOB are used to control the SuperPID?

  • Do you ship to Pakistan???If so what are the charges if any???

    You can determine if the country is serviceable by:
    - selecting the items you want to purchase on the website
    - go to the cart (shopping cart top left of any webpage)
    - log in, or register
    - Enter the address and click on calculate shipping.

    The webpage will return the direct rates and whether your area is serviced or not. Feel free to enter any address as long as you are able to receive the package from that address.

    The shipping times are determined by the service you select in the shopping cart. If a machine is purchased, we generally have a one week lead time unless otherwise stated in the description of the machine's product page.

    Click the link to respond:
    Do you ship to Pakistan???If so what are the charges if any???