Dealing with our USB BoB, the potentiometer that will be used in the key jog, is a 5V, 5k - 10k Ohm potentiometer.

Click the link to add information to this solution:
I am building a cnc mill using your USB controller and i would like to know what is the specification of potentiometer used for adjusting manual axis jog speed

The speed on the keyboard jog header is controls the jog travel speed.

The speed pin would be connected to the wiper of a potentiometer and the other two leads of the potentiometer would be connected: one lead to GND and the other lead to 5V.

Click the link to add information to this solution:
On the USB BOB, is the "speed" on the Keyboard Jog control the travel or spindle speed?

Yes, you can use 2 motors in the same axis output, however you will still need a driver for that motor! Also depending on the orientation on which you mount the motor you might have to invert the direction of the motor, and that will be simple by swapping the A+,A-, to the B+,B- locations and vice versa, from the driver to the motor wiring.

Also you can run a slave motor using another axis on the board, and setting it up in the Planet-CNC settings.

Planet-CNC/File/Settings/Axes, here you will enter 3 in the Number of Axes location, and then change the Function of the Axis 4 to Slave 1. There you will have the 4th axis or A-axis be a slave for the x-axis.
Slave 1 - X-Axis
Slave 2 - Y-Axis
Slave 3 - A-Axis
Slave 4 - B-Axis
Etc...




Additional Information:
Do you act as if it's one motor and it goes to one controller on the motherboard?

Click the link to add information to this solution:
Can I run two stepper motors off the same axis output on the USB controller?

No, the red mach3 USB controller will only work with mach3, you will need the pokeys57cnc. This controller will work with mach3 or mach4.
Here is a link:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Click the link to add information to this solution:
Hi, is it possible to operate red USB controller with Mach4? What plugins do I need? Thank you.

The USB Interface can only be used with the Planet-CNC software which runs under the windows operating system.

Click the link to add information to this solution:
Can the USB CNC Controller be used with LinuxCNC?

Unfortunately, we don't sell the planet-cnc controller anymore. They made a change to their software that prohibits us from creating the open source board.

We do sell three other boards that may work for you.

The Pokeys57CNC board is the mose feature rich and will work with both Mach3 and Mach4:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

The MAch3 USB board is a good inexpensive interface that will work well if you need the interface to be USB only:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Our in-house parallel breakout board (ytou need a parallel port for this interface to work):
https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay
Most motherboards have the parallel port connector on the motherboard, but not as a connector on the back of the computer case.

Click the link to add information to this solution:
Do you sell the 3 axis electronics combo , for heavy gantry , with the new Planet CNC usb controller ?

The PlanetCNC USB software, like most machine control software, can be used to control a laser engraver/cutter. The typical modification is to use the Z axis down signal to fire the laser, analogous to an endmill cutting into the workpiece from an initial position above it.

For the second question, it is important to note that BYCNC machines are not based on PlanetCNC software, or any other particular machine control system. The machines themselves will accept standard signals from a wide variety of machine control systems, not just PlanetCNC or Mach3. This allows maximum flexibility for the customer to choose their own preferred software for this part of the toolchain.

That said, our machines will accept a laser head either in lieu of or in addition to a spindle. Here is an example of a combination spindle/laser mount for our greenBull machine: https://buildyourcnc.com/item/cnc-machine-laser-spindle-combo-head. We have all the parts you would need to add laser functionality to your machine here: https://buildyourcnc.com/LaserComponents.aspx, if you feel comfortable assembling your own package. Also, feel free to contact our sales department for a quote if you need a custom assembly.

Click the link to add information to this solution:
Can the Planet CNC USB controller be used with a laser engraver/cutter? Can the build your own CNC based on the Planet CNC USB controller accept a Laser head instead of a router?

I created a video to demonstrate how to use the outputs on the Mach3 USB controller. You can find this video on the following page:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Scroll down to the 5th video on that page. The title of the video is: Mach3 USB Controller Outputs

Click the link to add information to this solution:
How do I use the outputs on the Mach3 USB controller?

The board has been developed and we are currently waiting to receive developer info from the makers of Mach4 so we can proceed with testing compatibility. There is no definite time frame but we are hopeful it will be released within the next couple months.

Click the link to add information to this solution:
Any timing on the USB Controller board for Mach-4

I would suggest using the NPN proximity sensor for the Mach3 USB or the Pokeys57cnc. The proximity sensors have a top DC voltage limit of 30 volts, so it would be best to use the 24V power supply that is used to power the controller. Both controllers have a 24V power requirement, so that is convenient.

The blue wire of the proximity sensor is the GND wire and is connected to the 24V power supply's V- terminal. The brown wire is the positive wire and is connected to the V+ terminal of the 24V power supply. The black wire is the signal wire and is connected to the input terminal of the controller.

Click the link to add information to this solution:
How can I connect an inductive proximity sensor to the Mach3 USB controller?

The use of the hex inverter in the application to invert a direction signal to have a motor run in the reverse directions is relatively simple.

First, go to this link and look at the chip diagram:
https://www.buildyourcnc.com/item/electronicsAndMotors-hex-inverter-breakout-newbiehack-integrated_circuits-hex-inverter

Connect 5V from the USB interface tothe VCC pin. The pin on the keyboard jog header can be used. Connect the GND pin from the USB interface to the GND pin on the hex inverter. Connect the CW terminal from the USB interface to the 1A pin on the hex inverter. Connect the 1Y pin from the hex inverter to the driver.

Additional Information:
I got a question??? I am a dummy when it comes to cnc. I got 6040 1500kw water cold engraver 3 axis from china. I can not get anything out of them pertaining help they keep telling me the same thing over and over and over and I'm doing it and send them pictures that I know. Anyway email me a wiring diagram for the PRT 1500 watt spindle motor control box and has the emergency stop on and off switch manual PC and of course yhe screanm fultonsbusiness@gmail.com

Additional Information:
I got a question??? I am a dummy when it comes to cnc. I got 6040 1500kw water cold engraver 3 axis from china. I can not get anything out of them pertaining help they keep telling me the same thing over and over and over and I'm doing it and send them pictures that I know. Anyway email me a wiring diagram for the PRT 1500 watt spindle motor control box and has the emergency stop on and off switch manual PC and of course yhe screanm fultonsbusiness@gmail.com

Click the link to add information to this solution:
Is there a wiring diagram for hooking up your hex inverter between your USB breakout board and the controller?

The Mach3 100 kHz controller may be able to support the Sherline 1/2 pulse mode, but I have not tried it. There is no information in the documentation that is related to the parameter that can be set in Mach3 for the Sherline 1/2 pulse mode. You may be able to play with the available kHz ranges that the plugin allows to see if there is a pulse width that meets the Sherline 1/2 pulse mode specification.

Click the link to add information to this solution:
[575] Does the USB MACH3 controller support Sherline 1/2 pulse mode?

You can find all of the wiring instructions for the Mach3 USB controller here:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Scroll down until you see the videos. The wiring instructions cover wiring all of the axes, setting up the inputs to sense limit switches, setting up the outputs and how to diagnose the outputs, setting up an external relay to control external devices, and setting up spindle speed.

Click the link to add information to this solution:
where can I find wiring instructions for the Mach3 USB controller?

The Mach3 usb controller/interface has instructions and videos on this page:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

There is a 5 step process on that page to install the plug-in and the configuration xml file that is necessary for the proper functioning of the controller.

The videos on that page also demonstrate in detail how to install the software, plug-ins, xml file and wiring and testing most of the features of the Mach3 USB interface.

Hope this helps.

Additional Information:


Additional Information:


Additional Information:
good day, does this controller board support the M11/M10 command set.

Click the link to add information to this solution:
How do you install the software for the Mach3 USB controller?

Yes, you can use a corner plate very easily. You will want to make a corner plate that has three independent plates that do not conduct with each other. Each of these plates will be connected to a different input (i.e. IN1 for X, IN2 for Y and IN3 for Z). The end mill or tool that is inserted into the spindle will connect to V- of the 24V power supply, or the DCM on the controller, which is connected to the 24V V-. Then, you can use the ref all home button on the program run screen of Mach3.

Click the link to add information to this solution:
Is there a way to use an X,Y plate that will only be responsible for corner finding in Mach3 with the Mach3 USB controller?

At this time we are working to release a new USB controller board that will be compatible with Mach4 software and do not have any immediate plans to update the Planet-CNC USB board.

Click the link to add information to this solution:
Are there plans to release a USB Controller to work with the Planet CNC Output Board for more advanced spindle control from within Planet CNC?

As long as the Ethernet cable is not next to stepper motor cables (between the stepper motor and the stepper motor driver) you should be fine. If you are using a spindle, make sure to shield the cable between the spindle and the VFD as well.

Additional Information:
One of my customers is testing this scenario. He is using CAT7 Ethernet cable which is double shielded. I/He will post the results when tested.

Click the link to add information to this solution:
I would like to mount the CNC controller to the gantry and use the ethernet cable routed through the cable carrier, is ther ok?

The instructions on how to use a plate for z-axis homing (moveable sensor) can be found here:

http://www.planet-cnc.com/faq/moveable_sensor/

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
How do you zero the z axis using a plate with the planet-cnc software and your USB controller?

The wiring instructions for the USB controller can be found here: https://www.buildyourcnc.com/tutorials/tutorial-Electronics-USB-Interface-Wiring

Click the link to add information to this solution:
how to connect USB controller to the drivers. Any instructions/video other then html datasheet?