You can find the wiring diagrams for the blackTooth on step 105 and 106 on the list of instructions on the blackTooth page. Step 105 pertains to the parallel breakout board and step 106 pertains to the USB interface board.

Additional Information:
wire size

Click the link to add information to this solution:
WHERE ARE THE WIRING DIAGRAMS FOR BLACKTOOTH LASER CUTTER IN INSTRUCTIONS?

You can find the wiring diagram for the Mach3 USB card on its product page here:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Here is a direct link to the diagram:
https://www.buildyourcnc.com/Documents/Electric%20Wiring%20Diagram.pdf

Click the link to add information to this solution:
I need wiring instructions for the ST- USB MOTION CARD

can not get the limit switches to work on the usb controller board

Additional Information:
Wiring the motors to the drivers for our 8 wire motor is probably the 425 oz-in NEMA 24 stepping motor. Here is the URL for the diagram of the motor:
https://www.buildyourcnc.com/Documents/PN.SM60HT86-2008BF-U%20(inhouse%20PN.60BYGH303-13)%20(1).pdf

Wire it in bipolar parallel as specified on the data sheet.

Here is the URL for the motor to check if it is the same that you purchased.
https://www.buildyourcnc.com/item/electronicsAndMotors-nema24-425ozin

The USB mach3 board URL is here:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

The wiring diagram is on that page and instruction on how to use it.

Click the link to add information to this solution:
I recently purchased the 3 axis mach3 usb kit the motors have 8 different colored wires (no stripes on wire just solid color) all instructions have different colors. cannot find tutorals. does the mach 3 hook up same as planet? please let me know where I can find wiring diagram to hook up mach 3 usb BOB and motors (I am new to this kind of work projects)

I would suggest using the NPN proximity sensor for the Mach3 USB or the Pokeys57cnc. The proximity sensors have a top DC voltage limit of 30 volts, so it would be best to use the 24V power supply that is used to power the controller. Both controllers have a 24V power requirement, so that is convenient.

The blue wire of the proximity sensor is the GND wire and is connected to the 24V power supply's V- terminal. The brown wire is the positive wire and is connected to the V+ terminal of the 24V power supply. The black wire is the signal wire and is connected to the input terminal of the controller.

Click the link to add information to this solution:
How can I connect an inductive proximity sensor to the Mach3 USB controller?

Yes, you can add a relay to the Mach3 USB controller. The relay must be a 24V relay on it's input side and be able to be set to active low. I demonstrate this in a video on the following page:
https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

The video is titled: Mach3 USB Controller Outputs

Click the link to add information to this solution:
Can I add a relay to the Mach3 USB controller?

The Mach3 usb controller/interface has instructions and videos on this page:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

There is a 5 step process on that page to install the plug-in and the configuration xml file that is necessary for the proper functioning of the controller.

The videos on that page also demonstrate in detail how to install the software, plug-ins, xml file and wiring and testing most of the features of the Mach3 USB interface.

Hope this helps.

Additional Information:


Additional Information:


Additional Information:
good day, does this controller board support the M11/M10 command set.

Click the link to add information to this solution:
How do you install the software for the Mach3 USB controller?

You can use a Pickit 2 programming to load firmware onto the usb driver. The USB use a Microchip pic microcontroller. If you can manage writing a program for the Pic microcontroller and have a Pickit 2 firmware uploader (programmer), you should have no problem.

Click the link to add information to this solution:
Does the USB controller come with driver installation instructions so we could create our own user interface to communicate with the motor?

The datasheet for the parallel breakout board is here:
https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay#prettyPhoto/2/

The datasheet for the USB interface is here:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout#prettyPhoto/2/


Additional Information:
20

Click the link to add information to this solution:
I need wiring instructions for the breakout board you sent yesterday. It is not like the one in the videos and I don't know where to connect the 5V. No data sheet or anything.

If the outputs are not functioning as expected on the Mach3 USB controller, confirm that the port for the output is 3. This is a part of the configuration I did not show on the video I created on using the outputs for the RNRMotion controller.

Additional Information:
Thanks for your help. Under Ports & Pins>Output Signals I show Output#1 through Output#4 as Enabled. All have Port# set to 3. Pin Numbers for each Output# are same as Output# (Output#1 set to Pin Number 1, etc.).
Still no voltage showing on output 1 (of the board) when I input M3 in the Input section of the MDI tab. However if (in Spindle Setup tab) I set (in "Relay Control")M3 Output# to 3 and M4 Output# to 4 things work as expected. Is it possible to have the M3 signal show up on Output#1?
Thanks again.

Additional Information:

Click the link to add information to this solution:
Mach3 USB interface board initial setup. Following instructions in the video "Mach3 USB controller outputs". Arrow keys cause red LED to blink, but cannot duplicate 24V output with M3 (or M4) commands as shown in the video. Do I need to re-install Mach3?

The use of the hex inverter in the application to invert a direction signal to have a motor run in the reverse directions is relatively simple.

First, go to this link and look at the chip diagram:
https://www.buildyourcnc.com/item/electronicsAndMotors-hex-inverter-breakout-newbiehack-integrated_circuits-hex-inverter

Connect 5V from the USB interface tothe VCC pin. The pin on the keyboard jog header can be used. Connect the GND pin from the USB interface to the GND pin on the hex inverter. Connect the CW terminal from the USB interface to the 1A pin on the hex inverter. Connect the 1Y pin from the hex inverter to the driver.

Additional Information:
I got a question??? I am a dummy when it comes to cnc. I got 6040 1500kw water cold engraver 3 axis from china. I can not get anything out of them pertaining help they keep telling me the same thing over and over and over and I'm doing it and send them pictures that I know. Anyway email me a wiring diagram for the PRT 1500 watt spindle motor control box and has the emergency stop on and off switch manual PC and of course yhe screanm fultonsbusiness@gmail.com

Additional Information:
I got a question??? I am a dummy when it comes to cnc. I got 6040 1500kw water cold engraver 3 axis from china. I can not get anything out of them pertaining help they keep telling me the same thing over and over and over and I'm doing it and send them pictures that I know. Anyway email me a wiring diagram for the PRT 1500 watt spindle motor control box and has the emergency stop on and off switch manual PC and of course yhe screanm fultonsbusiness@gmail.com

Click the link to add information to this solution:
Is there a wiring diagram for hooking up your hex inverter between your USB breakout board and the controller?

I created a video to demonstrate how to use the outputs on the Mach3 USB controller. You can find this video on the following page:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Scroll down to the 5th video on that page. The title of the video is: Mach3 USB Controller Outputs

Click the link to add information to this solution:
How do I use the outputs on the Mach3 USB controller?

The USB controller board is currently only compatible with Planet-CNC software.

Click the link to add information to this solution:
Can I use Mach3 or 4 with your USB controller PCA?

The Mach3 100 kHz controller may be able to support the Sherline 1/2 pulse mode, but I have not tried it. There is no information in the documentation that is related to the parameter that can be set in Mach3 for the Sherline 1/2 pulse mode. You may be able to play with the available kHz ranges that the plugin allows to see if there is a pulse width that meets the Sherline 1/2 pulse mode specification.

Click the link to add information to this solution:
[575] Does the USB MACH3 controller support Sherline 1/2 pulse mode?

Yes, you can use a corner plate very easily. You will want to make a corner plate that has three independent plates that do not conduct with each other. Each of these plates will be connected to a different input (i.e. IN1 for X, IN2 for Y and IN3 for Z). The end mill or tool that is inserted into the spindle will connect to V- of the 24V power supply, or the DCM on the controller, which is connected to the 24V V-. Then, you can use the ref all home button on the program run screen of Mach3.

Click the link to add information to this solution:
Is there a way to use an X,Y plate that will only be responsible for corner finding in Mach3 with the Mach3 USB controller?

I would recommend using our 5.6 amp driver as a replacement for the TX14207 driver. Apparently, those drivers are found in the 6040 CNC routers and will not contain documentation since it is typically sold as a part of a greater assembly. Here is the link to the recommended driver:
https://buildyourcnc.com/item/electronicsAndMotors-stepper-driver-6!0a

Click the link to add information to this solution:
Where can I get a motor driver "TX14207", or a substitute with instructions?

To use a touch plate on any controller, all you need is a conductive flat material with a known thickness and some wire and alligator clips. Solder a wire to the touch plate and connect the other end of the wire to the free input terminal of the controller. Connect a wire with an alligator clip to the ground of the controller (on the Mach3 USB controller, this ground is the DCM terminal, or the digital gnd on the 24VDC power supply). Connect the alligator clip to the end mill.

You can either use a script to serve as the probe, or you can use the ref all home button and setup the touch plate as a home switch.

Additional Information:
I connect wire to cmd- and to in2. I cant getbit to work, what arecthe corresponding ports and pins to usenin mach3? Please help.

Click the link to add information to this solution:
Hello, Can I hook up a Z axis touch plate to the usb controller?

All the options for and variations of our blackTooth laser cutter/engraver are available on our website here https://buildyourcnc.com/blackToothLaserCutterAndEngraver.aspx#prettyPhoto. The wiring diagram is available here: https://buildyourcnc.com/blackToothLaserCutterAndEngraver.aspx#prettyPhoto/0/
We do not offer plans or a bill of materials for our machines at this time, but if you are interested in doing your own from scratch you can learn a lot about the design and build process from our tutorials. We wish you success in your endeavors.

Click the link to add information to this solution:
How can i get a complete list of all the components (electronics) I need for a CNC laser cutter with the laser controller? A wiring Diagram would probably be very helpful.

No, the Mach3 USB controller only works with Mach3. If you wish to use Mach4, I would recommend this very feature-rich controller:
Pokeys57CNC controller https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Click the link to add information to this solution:
does the Mach3 USB Controller support Mach4

I will check

Additional Information:
The license was purchased and the developer is sending you the license shortly.

Click the link to add information to this solution:
I purchased license for Mach3 yesterday. When do I receive download instructions and key?