Yes, proximity sensors work similarly to limit switches. There are three connections that connect to the signal (input terminal) and two power connections that is connected to the 24V power supply that supplies the Mach3 USB controller. I have only tested NPN proximity switches with that controller in NO (normally open mode).

Click the link to add information to this solution:
Is it possible to add proximity sensors with your USB Controller Board

We could not guarantee, nor say, whether or not your current software would be able to utilize the USB breakout board. Our USB breakout board is designed for use with Planet CNC software found here, http://www.planet-cnc.com/index.php?page=software

As far as we know, this is the only CNC Controller software that operates on a USB breakout controller.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
I want to change my old DSP controller and break out board with new one in your site that support usb it is possible ? if yes can we contact us to talking about details ?

Our spindle VFD's, have a multitude of different connectors that can be used for different operations. There is a manual that comes with each VFD, and you can refer to page 11 for different functions and descriptions.

We currently have a PWM, working with our machine, however it is connected via USB, and setup through Mach 3.
Also if you may have misplaced or lost the manual here is a link to the pdf:

(https://www.google.com/url?sa=t&rct=j&q=&esrc=s&source=web&cd=1&cad=rja&uact=8&ved=0CCAQFjAAahUKEwibxaaIndTHAhXQlogKHZVyDFE&url=http%3A%2F%2Fwww.c-n-c.cz%2Fdownload%2Ffile.php%3Fid%3D42252&ei=_cHkVdvSC9CtogSV5bGIBQ&usg=AFQjCNHTQcxs-KhJkvkhMdxVFPzkoYJtsA&sig2=JAcZawTGMuC-t4wmn1z-rA)

Click the link to add information to this solution:
It is possible to control externally the 1.5kW Inverter (VFD) (220 Volt) with PWM so i can control the spindle rotation? Do you have the documentation? Thank you

We could not guarantee, nor say, whether or not your current software would be able to utilize the USB breakout board. Our USB breakout board is designed for use with Planet CNC software found here, http://www.planet-cnc.com/index.php?page=software

As far as we know, this is the only CNC Controller software that operates on a USB breakout controller.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
Is it possible to manage USB Controller (Breakout) from my own (custom) Windows application? Is there a driver API or smth for that?

The instructions on how to use a plate for z-axis homing (moveable sensor) can be found here:

http://www.planet-cnc.com/faq/moveable_sensor/

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
How do you zero the z axis using a plate with the planet-cnc software and your USB controller?

Yes, you can connect a THC, Torch Height Controller, with the Mach3 USB controller. The THC uses the inputs to determine if the z axis needs to move up or down according to the arc of the plasma torch. The THC connects its outputs to the inputs of the controller so the controller will be informed of the states of the plasma torch.

Click the link to add information to this solution:
I am interested in using the Mach3 USB interface board. I was wondering if there was a way to run a torch height controller with this board for use with a plasma cutter, and if so do you know of any THCs that will work. Thank you.

Plans are not sold at this time. If you are interested in getting a machine in Europe we have some options for you. Please email sales@buildyourcnc.com for more details.

Click the link to add information to this solution:
Hi, is it possible to buy only plans. I live in Europe and it gets quite pricy with shipping costs.

All USB boards, are tested and checked before shipment for all axis, and inputs. Here is a link with clear instructions on how to setup Planet-CNC (http://www.planet-cnc.com/faq/machine_setup/).

Please check continuity for each individual wire and for any crossover disruption when wiring your board, try to wire each as cleanly and with out crossing any live power wires and or motor motion wires.

Click the link to add information to this solution:
Email link is not functioning. (continuation of z+ limit question) The Usb cnc controller is now switching what the limits are. IE: X- is showing up as Y+ ect. Is this a bad board? Thank you.

Absolutely! You can have almost unlimited limit switches and home switches on this controller. It all comes down to the wiring scheme used. I recommend the home switches be on separate input terminals. For example, IN1 would have the X home switch, IN2 would have the Y home switch and, IN3 would have the Z home switch if you plan on using home switches for the Z axis.

Adding the limit switches, these can be located on any input you want, even on the IN1, 2 or 3. The wiring scheme I like to use is as follows:
- IN1 has the X home, X limit ++, and X Limit --
- IN1 has the Y home, Y limit ++, and Y Limit --
- IN1 has the Z home, Z limit ++, and Z Limit --

In most cases, the Limit -- is the same switch as the Home switch.

These can be wired as NC (Normally closed) as a serial scheme, or as NO (Normally open) as a parallel scheme.

To understand the limits and wiring schemes, check out this video:

Click the link to add information to this solution:
[575] Hi, for the manage the limit switches, is it possible to have, for example, the same limit switch for X-- and X homing? And what is the configuration in mach3? In my CNC machine they are in the same position. Thank you

To implement a electronics combo to run you Proxxon MF70, you will need to find the correct drive components (ACME screw, linear rail, etc) and look into any specific modifications needed to your rig.
I would recommend the USB 3 Axis Large Motors Electronics w/ USB Interface Board.
Since the machine is metal, our larger motors would be highly recommended.

We have not done this conversion, through research is recommended.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
Hi I have a Proxxon MF70, I want to add 3axis stepper with controller and software by USB. Can you suggest a kit for me? Thanks.

The USB controller will only work with the Planet-CNC software. This software is well made and will provide great functionality. The planet-cnc software delivers instructions to the microcontroller on the board and the microcontroller will send out the pulse trains needed to move the machine correctly.

There are two main alternatives if you want to use the mach3 software:
First, get a parallel port card and add it to your computer and get a parallel breakout board. If you have a laptop/notebook computer, this will not be possible.
Second, if you have a laptop, or really want to use the USB as the main interface for controlling the machine, you will need to get the smoothstepper board which works with mach3. The price combination is much higher than the USB controller with planet-cnc, but will work with Mach3.

Additional Information:


Additional Information:


Additional Information:
The planet cnc controller can be prone to electrical interference and has been known to cause such problems. In the first instance try to use a quality double sheilded USB cable, hopefully this will fix your problem. Alternatively you may need to sheild your limit switch, estop and or motor cabling. My pick is that a quality USB cable will fix it though, worked for me.

Click the link to add information to this solution:
I have your USB controller sitting here and want to control it with something other than PlanetCNC control software?

The BobCAD post processor that will work with the USB interface that uses the Planet-CNC software:

According to the Planet-cnc folks, wincnc or mach3 post-processors should work. According to a representative at BobCAD, mach3 post-processor should work.

Click the link to add information to this solution:
Do you know which BobCAD-CAM post processor works with your USB controller? Do you have a dll or command document to communicate with your USB controller?

The Mach3 USB controller can only output pulses and direction signals (5V logic signals).

To connect your Mach3 USB controller RNR controller with a servo AC that has a 24V open collector, you will need to use a level shifter circuit to convert the 5V pulses from the controller to 24V pulses that the servo can accept.

One way to do this is to use a simple transistor-based level shifter circuit. Here are the steps to connect your Mach3 USB controller RNR controller with a servo AC using a level shifter circuit:

Connect the 5V output signals from the Mach3 USB controller RNR controller to the base of the NPN transistor in the level shifter circuit.

Connect the collector of the NPN transistor to the 24V power supply.

Connect the open collector output of the servo AC to the emitter of the NPN transistor.

Finally, connect the ground of the Mach3 USB controller RNR controller and the servo AC to the ground of the 24V power supply.

The level shifter circuit will act as a switch, allowing the 24V power to flow to the servo AC when the 5V signal from the controller is present.

Remember that the MAch3 USB controller only outputs pulses for steps per rotation of a motor. If the servo requires a different method of motor rotation, this will not work.

Click the link to add information to this solution:
[575] Hello. I have rnr controller. My problem is connection with servo ac. My servopack have logic Voltage 24v open collector. How Connect and what i need to Connect rnr with servo if rnr have 5v logic. Thx

You can cut at varying depths with the 40w laser cutting and engraving machine. Each layer of engraving with the laser will leave behind a black charred film that will reduce the effectiveness of the engraving for deeper layers; therefore, a very strong air assist will be needed to blow this film off of the surface of the material.

CNC machines are more successful and efficient at carving and should be considered.

Click the link to add information to this solution:
I wonder if it is possible to do 3d engraving with the 40w laser kit? different depths is the same piece of wood.

Yes, you can use a corner plate very easily. You will want to make a corner plate that has three independent plates that do not conduct with each other. Each of these plates will be connected to a different input (i.e. IN1 for X, IN2 for Y and IN3 for Z). The end mill or tool that is inserted into the spindle will connect to V- of the 24V power supply, or the DCM on the controller, which is connected to the 24V V-. Then, you can use the ref all home button on the program run screen of Mach3.

Click the link to add information to this solution:
Is there a way to use an X,Y plate that will only be responsible for corner finding in Mach3 with the Mach3 USB controller?

If the outputs are not functioning as expected on the Mach3 USB controller, confirm that the port for the output is 3. This is a part of the configuration I did not show on the video I created on using the outputs for the RNRMotion controller.

Additional Information:
Thanks for your help. Under Ports & Pins>Output Signals I show Output#1 through Output#4 as Enabled. All have Port# set to 3. Pin Numbers for each Output# are same as Output# (Output#1 set to Pin Number 1, etc.).
Still no voltage showing on output 1 (of the board) when I input M3 in the Input section of the MDI tab. However if (in Spindle Setup tab) I set (in "Relay Control")M3 Output# to 3 and M4 Output# to 4 things work as expected. Is it possible to have the M3 signal show up on Output#1?
Thanks again.

Additional Information:

Click the link to add information to this solution:
Mach3 USB interface board initial setup. Following instructions in the video "Mach3 USB controller outputs". Arrow keys cause red LED to blink, but cannot duplicate 24V output with M3 (or M4) commands as shown in the video. Do I need to re-install Mach3?

I would suggest using the NPN proximity sensor for the Mach3 USB or the Pokeys57cnc. The proximity sensors have a top DC voltage limit of 30 volts, so it would be best to use the 24V power supply that is used to power the controller. Both controllers have a 24V power requirement, so that is convenient.

The blue wire of the proximity sensor is the GND wire and is connected to the 24V power supply's V- terminal. The brown wire is the positive wire and is connected to the V+ terminal of the 24V power supply. The black wire is the signal wire and is connected to the input terminal of the controller.

Click the link to add information to this solution:
Good evening, if I wanted to use your inductive proximity sensor's with your USB interface board what would I need besides the sensors I would be using 5 of the sensors. I have a 48V 12amp power supply. Thank you

With our machines the ipm capable is very dependent on the bit/end mill (the more flutes you have the faster the material will be cut) you are using as well if it is with a router or a spindle, as well as the density of the material. If those items are taken into effect reaching 400 ipm would not be a problem with the greenLean/other machines equipped with our 2.2 kW spindle, and a decent end mill.

Click the link to add information to this solution:
Interested in the greenLean -- I need to be able to achieve 400 ipm on plywood-- is it possible?

All of our controller will allow two steppers on any of the axes. Multiple stepper motors and drivers on a single axis is more a function of the way the stepper motor drives are connected to the output pins of the controller. To connect two stepper drivers to a single axis, you need to connect the output pins (dir and step) to each of the two stepper motor drivers.

Consider the controller on cost, features and how they are connected to the computer.

Out lowest cost controllers are:

Mach3 USB board - Has good features and uses the USB from the computer as the main connection
https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Parallel Breakout - The computer generates the main signals and this board conditions the signals for the drivers. Although it requires the parallel port from older computer, the board has the most broad compatibility with control software out there including Mach3 and LinuxCNC.
https://buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

Highest cost but most feature rich:

Pokey57CNC - works with both Mach3 and Mach4
https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Click the link to add information to this solution:
I am looking for a controller for a 3 axis dual Y stepper cnc machine. If at all possible I would like a list of the parts that will be needed. I prefer to go with an ethernet setup vs a parallel port.