Yes, you can connect a THC, Torch Height Controller, with the Mach3 USB controller. The THC uses the inputs to determine if the z axis needs to move up or down according to the arc of the plasma torch. The THC connects its outputs to the inputs of the controller so the controller will be informed of the states of the plasma torch.

Click the link to add information to this solution:
I am interested in using the Mach3 USB interface board. I was wondering if there was a way to run a torch height controller with this board for use with a plasma cutter, and if so do you know of any THCs that will work. Thank you.

I also place the controller very close to the drivers (on the back of the gantry). All of the cables are shielded. The only long cables are the mains power cables and the USB cable. The USB cable is shielded and contains active repeaters.

There is no problem putting all of the electronics in a box and using long cables to the motors. This is the way I did it for a very long time.

Click the link to add information to this solution:
Great site. I saw your videos of wiring the Mach3 USB controller. You place the drivers next to the Steppers. This means that you have very long leads to the USB Board? What about the placement of the controlling PC? Is it a problem to have the USB board, PSUs and Drivers in a control box and long leads to the steppers? Thank you.

"Soft limits are used to decelerate machine to stop before machine is stopped hard way at limit switch or before it crashes. I recommend "Soft Limits Decelerate" and "Soft Limits Strict" settings are also checked. Sometimes we need to disable soft limits and there is a command for this in menu "Machine/Soft Limits". When soft limit is triggered position display will be yellow."

Are the soft limits "grayed out"?
Here is a link to a very useful forum post from the Planet-CNC crew:
http://www.planet-cnc.com/faq/machine_setup/



Additional Information:
i keep getting scratches when engraving pictures on dog tags

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
Using USB Controller Board with Planet-CNC software. The S/W recognizes limit switches but not soft limits. Help?

Thanks. I updated that option to reflect that it has no pendant.

Click the link to add information to this solution:
[823] The description for this stand alone 3.1 controller describes the pendant as being included, but when you link to the Amazon site for this item, the MPG pendant is not included int the $250 price.

The Mach3 USB interface board requires 24V relays externally. There are no relays on the mach3 usb board. If you use an external relay on the mach3 usb board, the relay connects to the V+ which is 24V and the output pin is the return.

Additional Information:
I understand what you are saying. Does your relay board work with the Mach3 USB board? If not, what relay board do you suggest to work with this usb controller?

Additional Information:
Our relay board works with our parallel breakout board. An off the shelf SSR (Solid State Relay) made for 24V should work fine.

Click the link to add information to this solution:
I bought a 'BuildyourCNC V1' relay board to go with my mach3 usb controller. I have been sent a 'Songle' relay. It's not the one in your picture and it's got different connections, for which there isn't a wiring diagram. The one I ordered says it is 5v, this one seems to be saying it's a 24v unit. Can you please explain what has happened? Thanks

The Mach3 USB interface board requires 24V relays externally. There are no relays on the mach3 usb board. If you use an external relay on the mach3 usb board, the relay connects to the V+ which is 24V and the output pin is the return.

Additional Information:
I understand what you are saying. Does your relay board work with the Mach3 USB board? If not, what relay board do you suggest to work with this usb controller?

Additional Information:
Our relay board works with our parallel breakout board. An off the shelf SSR (Solid State Relay) made for 24V should work fine.

Click the link to add information to this solution:
I bought a 'BuildyourCNC V1' relay board to go with my mach3 usb controller. I have been sent a 'Songle' relay. It's not the one in your picture and it's got different connections, for which there isn't a wiring diagram. The one I ordered says it is 5v, this one seems to be saying it's a 24v unit. Can you please explain what has happened? Thanks

Dealing with our USB BoB, the potentiometer that will be used in the key jog, is a 5V, 5k - 10k Ohm potentiometer.

Click the link to add information to this solution:
I am building a cnc mill using your USB controller and i would like to know what is the specification of potentiometer used for adjusting manual axis jog speed

You should have no problem connecting the Pokeys57CNC controller to the drivers of your machine as long as the drivers have step (Pulse or PUL) and direction (DIR) terminals. You will need the cable pack that is sold separately so you can connect the headers/connectors of the pokeys57cnc controller to the drivers using ribbon cables.

I show this process in great detail on this page:
https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Is you scroll down on the page, you will see a set of videos that show the process step-by-step.

Click the link to add information to this solution:
I have a ShopBot CNC that was converted to Mach 3. The controller has gone out. I pourchased your Pokeys57 board, but I'm not sure I have everything I need. I think my motor drivers are OK, but am not sure how to wire them to what I purchased from you. Need Help. How can we make this work, or do I need a different board to distribute the movement signals to my drivers?

At this time we are working to release a new USB controller board that will be compatible with Mach4 software and do not have any immediate plans to update the Planet-CNC USB board.

Click the link to add information to this solution:
Are there plans to release a USB Controller to work with the Planet CNC Output Board for more advanced spindle control from within Planet CNC?

BYCNC Response:
This is correct. You will need to use a method appropriate for the software you are using. Also remember that NC switches are typically wired in series, while NO switches are normally wired in parallel.

User Response:
I am using the cnc planet software for your USB board. Are the limit configurations in this software?

BYCNC Response:
Yes, Planet CNC software is compatible with the use of limit switches. Configuration information will depend on your specific application. You can view Planet CNC's information here: http://www.planet-cnc.com/files/CNCUSBController.pdf

Click the link to add information to this solution:
LIMIT SWITCHES FOR AXIS. THE PRINT SHOWS THAT YOU CAN WIRE LIMITS EITHER N.O. OR N.C. SO IF THIS IS CORRECT I WOULD NEED TO TELL BOARD IN SOFTWARE HOW LOOK AT THESE LIMITS, I'M GOING GET AN INPUT LOOSE DEPEND ON IT.

I would not recommend slaving an axis using the method of taking an additional axis from the USB interface. Instead, wire both drivers to a single axis on the USB interface. This will insure perfect signal output to both drivers. If you requre the motors to spin in opposite directions, simply wire one of the motors to the driver reversing the coil A and B connections, or use a hex inverter (https://www.buildyourcnc.com/tutorials/Tutorial-Two-Motors-Spinning-Oppositely-On-Single-Axis).

Click the link to add information to this solution:
I purchased a USB Breakout board, motors and drivers, paid for CNC USB Controller Software and I CAN NOT "Slave" an axis, but there is an option to do that. The moment I connect USB Breakout Board "Slave" option becomes shaded and I can no longer select it (becomes not functional). What is going on? Need help asap. Thanks

Absolutely! You can have almost unlimited limit switches and home switches on this controller. It all comes down to the wiring scheme used. I recommend the home switches be on separate input terminals. For example, IN1 would have the X home switch, IN2 would have the Y home switch and, IN3 would have the Z home switch if you plan on using home switches for the Z axis.

Adding the limit switches, these can be located on any input you want, even on the IN1, 2 or 3. The wiring scheme I like to use is as follows:
- IN1 has the X home, X limit ++, and X Limit --
- IN1 has the Y home, Y limit ++, and Y Limit --
- IN1 has the Z home, Z limit ++, and Z Limit --

In most cases, the Limit -- is the same switch as the Home switch.

These can be wired as NC (Normally closed) as a serial scheme, or as NO (Normally open) as a parallel scheme.

To understand the limits and wiring schemes, check out this video:

Click the link to add information to this solution:
[575] Hi, for the manage the limit switches, is it possible to have, for example, the same limit switch for X-- and X homing? And what is the configuration in mach3? In my CNC machine they are in the same position. Thank you

This sounds like a problem with the step (pulse) signal. The driver motors receive two signals from the computer via the board -- one is high or low and tells the motors which direction to turn, one is a square wave pulsed signal(quick that tells the motor to turn or a constant high signal that tells the motor to maintain its position. With an oscilliscope you can check for proper signal at the board. If you bought the board from us, please contact us to arrange a return authorization.

Click the link to add information to this solution:
Y axis on usb controller not working. The motor gets power and holds but will not turn. I tried switching the same wires, driver, and motor over to the A axis on the controller and it works fine like that. I have double, and triple checked the wiring

Here are links to the sole pump and heat exchanger/fan. I am sending you amazon links sine I don't ahve listings of my pump and heat exchanger separately from my cooling system:
Pump: https://amzn.to/3R6zPbj
Fan/radiator (Heat exchanger): https://amzn.to/3UWOuqN

Click the link to add information to this solution:
I RECENTLY PURCHASED A REPALCEMENT 12V DC SWITCHING POWER SUPPLY, HOOKED IT UP BUR DID NOT THE PUMP AND RADIATOR. VERIFIED OUTPUT OF UNIT AT 12V. SO I'M ASSUMING ALSO NEED TO REPLACE CAN YOU SUPPLY ME LINK PURCHASE THEM?

I would suggest using the NPN proximity sensor for the Mach3 USB or the Pokeys57cnc. The proximity sensors have a top DC voltage limit of 30 volts, so it would be best to use the 24V power supply that is used to power the controller. Both controllers have a 24V power requirement, so that is convenient.

The blue wire of the proximity sensor is the GND wire and is connected to the 24V power supply's V- terminal. The brown wire is the positive wire and is connected to the V+ terminal of the 24V power supply. The black wire is the signal wire and is connected to the input terminal of the controller.

Click the link to add information to this solution:
Good evening, if I wanted to use your inductive proximity sensor's with your USB interface board what would I need besides the sensors I would be using 5 of the sensors. I have a 48V 12amp power supply. Thank you

If you want speed control, it is recommended to use the RS-485 connection on the VFD and use the control program such as Mach3 to communication serially with the VFD using this RS-485 connection.

If you would rather use a controller such as the PMDX-107 to simulate the effect of a potentiometer using the Aref, Aout and Agnd and the Rev/Dir and Fwd/Run terminals to control operation and direction, you can connect those to the VFD.

PMDX-107 Aout connects to the VI (analog voltage in). This is like the wiper on a potentiometer.
PMDX-107 Agnd connects to the ACM terminal on the VFD for Analog common.
PMDX-107 COM connects to DCM terminal on the VFD for Digital common.
PMDX-107 Fwd/Run connects to the FOR terminal on the VFD for Forward.
PMDX-107 Rev/Dir connects to the REV terminal on the VFD for Reverse.

Refer to your PMDX-107 manual to correctly configure your dip switch settings and make sure to calibrate (tweak) the speed control using the trimmer next to the terminals on the PMDX-107.

Click the link to add information to this solution:
I have the USB controller board and the 8825 step driver. I need a wiring diagram between the two. Specifically, what does the GND pin on the X-axis connect to? Also, what does the 5V pin on the driver connect to?

You can find a wiring diagram here:
https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout#prettyPhoto/2/

The CP terminal is wired to the step terminal on the 8825 step driver.
The CW terminal is wired to the direction terminal on the 8825 step driver.
The GND terminal connects to the GND on the 8825 step driver

The 5V connector on the driver simply powers the logic side of the chip and needs to connect to VCC pin on the keyboard jog.

Customer Response:
Thanks! Working now.

Click the link to add information to this solution:
I have the USB controller board and the 8825 step driver. I need a wiring diagram between the two. Specifically, what does the GND pin on the X-axis connect to? Also, what does the 5V pin on the driver connect to?

Planet CNC has the option to turn off these outputs on your USB board. Under the File/settings/Pins. You will have Spindle (M3,M4,M5) Coolant (M7,M8,M9) as available output pins. On the drop down tabs for these output pins you will have this option ( --- ), if selected it will turn of that output pin in your board and you will get not voltage change in the pin.

Additional Information:
Cannot activate output in mkx

Click the link to add information to this solution:
On the USB controller I am unable to get voltage from the Mist relay block on the board. The Flood and Spindle produce a voltage change correctly. Is there a setting I am missing?

Yes, here is the URL for the parallel breakout board that we sell:

https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

Click the link to add information to this solution:
can I purchase just the parallel controller board? I purchased the usb option 4 axis combo and would like to also try the system with my parallel port computer. Any help with this will be greatly appreciated; my goal is to implement mach4.