[ Log In ]
[ Register ]

Question #: 14620

Question: Is it possible to add proximity sensors with your USB Controller Board

Current Solution

Yes, proximity sensors work similarly to limit switches. There are three connections that connect to the signal (input terminal) and two power connections that is connected to the 24V power supply that supplies the Mach3 USB controller. I have only tested NPN proximity switches with that controller in NO (normally open mode).

Respond:

Other Possible Solutions to this Question

  • Hi, is it possible to operate red USB controller with Mach4? What plugins do I need? Thank you.

    No, the red mach3 USB controller will only work with mach3, you will need the pokeys57cnc. This controller will work with mach3 or mach4.
    Here is a link:
    https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

    Click the link to add information to this solution:
    Hi, is it possible to operate red USB controller with Mach4? What plugins do I need? Thank you.

  • if I wanted to use your inductive proximity sensor's with your USB interface board what would I need besides the sensors I would be using 5 of the sensors.

    I would suggest using the NPN proximity sensor for the Mach3 USB or the Pokeys57cnc. The proximity sensors have a top DC voltage limit of 30 volts, so it would be best to use the 24V power supply that is used to power the controller. Both controllers have a 24V power requirement, so that is convenient.

    The blue wire of the proximity sensor is the GND wire and is connected to the 24V power supply's V- terminal. The brown wire is the positive wire and is connected to the V+ terminal of the 24V power supply. The black wire is the signal wire and is connected to the input terminal of the controller.

    Click the link to add information to this solution:
    if I wanted to use your inductive proximity sensor's with your USB interface board what would I need besides the sensors I would be using 5 of the sensors.

  • Good evening, if I wanted to use your inductive proximity sensor's with your USB interface board what would I need besides the sensors I would be using 5 of the sensors. I have a 48V 12amp power supply. Thank you

    I would suggest using the NPN proximity sensor for the Mach3 USB or the Pokeys57cnc. The proximity sensors have a top DC voltage limit of 30 volts, so it would be best to use the 24V power supply that is used to power the controller. Both controllers have a 24V power requirement, so that is convenient.

    The blue wire of the proximity sensor is the GND wire and is connected to the 24V power supply's V- terminal. The brown wire is the positive wire and is connected to the V+ terminal of the 24V power supply. The black wire is the signal wire and is connected to the input terminal of the controller.

    Click the link to add information to this solution:
    Good evening, if I wanted to use your inductive proximity sensor's with your USB interface board what would I need besides the sensors I would be using 5 of the sensors. I have a 48V 12amp power supply. Thank you

  • How can I connect an inductive proximity sensor to the Mach3 USB controller?

    I would suggest using the NPN proximity sensor for the Mach3 USB or the Pokeys57cnc. The proximity sensors have a top DC voltage limit of 30 volts, so it would be best to use the 24V power supply that is used to power the controller. Both controllers have a 24V power requirement, so that is convenient.

    The blue wire of the proximity sensor is the GND wire and is connected to the 24V power supply's V- terminal. The brown wire is the positive wire and is connected to the V+ terminal of the 24V power supply. The black wire is the signal wire and is connected to the input terminal of the controller.

    Click the link to add information to this solution:
    How can I connect an inductive proximity sensor to the Mach3 USB controller?

  • Is it possible to manage USB Controller (Breakout) from my own (custom) Windows application? Is there a driver API or smth for that?

    We could not guarantee, nor say, whether or not your current software would be able to utilize the USB breakout board. Our USB breakout board is designed for use with Planet CNC software found here, http://www.planet-cnc.com/index.php?page=software

    As far as we know, this is the only CNC Controller software that operates on a USB breakout controller.

    Additional Information:



    Additional Information:



    Additional Information:

    Click the link to add information to this solution:
    Is it possible to manage USB Controller (Breakout) from my own (custom) Windows application? Is there a driver API or smth for that?

  • I have your USB controller sitting here and want to control it with something other than PlanetCNC control software?

    The USB controller will only work with the Planet-CNC software. This software is well made and will provide great functionality. The planet-cnc software delivers instructions to the microcontroller on the board and the microcontroller will send out the pulse trains needed to move the machine correctly.

    There are two main alternatives if you want to use the mach3 software:
    First, get a parallel port card and add it to your computer and get a parallel breakout board. If you have a laptop/notebook computer, this will not be possible.
    Second, if you have a laptop, or really want to use the USB as the main interface for controlling the machine, you will need to get the smoothstepper board which works with mach3. The price combination is much higher than the USB controller with planet-cnc, but will work with Mach3.

    Additional Information:


    Additional Information:


    Additional Information:
    The planet cnc controller can be prone to electrical interference and has been known to cause such problems. In the first instance try to use a quality double sheilded USB cable, hopefully this will fix your problem. Alternatively you may need to sheild your limit switch, estop and or motor cabling. My pick is that a quality USB cable will fix it though, worked for me.

    Click the link to add information to this solution:
    I have your USB controller sitting here and want to control it with something other than PlanetCNC control software?

  • Using your USB control board, is it possible to install and use a Z axis touch plate? If yes, what board connections would it be installed to?

    The instructions on how to use a plate for z-axis homing (moveable sensor) can be found here:

    http://www.planet-cnc.com/faq/moveable_sensor/

    Additional Information:



    Additional Information:



    Additional Information:

    Click the link to add information to this solution:
    Using your USB control board, is it possible to install and use a Z axis touch plate? If yes, what board connections would it be installed to?

  • Is there a wiring diagram for hooking up your hex inverter between your USB breakout board and the controller?

    The use of the hex inverter in the application to invert a direction signal to have a motor run in the reverse directions is relatively simple.

    First, go to this link and look at the chip diagram:
    https://www.buildyourcnc.com/item/electronicsAndMotors-hex-inverter-breakout-newbiehack-integrated_circuits-hex-inverter

    Connect 5V from the USB interface tothe VCC pin. The pin on the keyboard jog header can be used. Connect the GND pin from the USB interface to the GND pin on the hex inverter. Connect the CW terminal from the USB interface to the 1A pin on the hex inverter. Connect the 1Y pin from the hex inverter to the driver.

    Additional Information:
    I got a question??? I am a dummy when it comes to cnc. I got 6040 1500kw water cold engraver 3 axis from china. I can not get anything out of them pertaining help they keep telling me the same thing over and over and over and I'm doing it and send them pictures that I know. Anyway email me a wiring diagram for the PRT 1500 watt spindle motor control box and has the emergency stop on and off switch manual PC and of course yhe screanm fultonsbusiness@gmail.com

    Additional Information:
    I got a question??? I am a dummy when it comes to cnc. I got 6040 1500kw water cold engraver 3 axis from china. I can not get anything out of them pertaining help they keep telling me the same thing over and over and over and I'm doing it and send them pictures that I know. Anyway email me a wiring diagram for the PRT 1500 watt spindle motor control box and has the emergency stop on and off switch manual PC and of course yhe screanm fultonsbusiness@gmail.com

    Click the link to add information to this solution:
    Is there a wiring diagram for hooking up your hex inverter between your USB breakout board and the controller?

  • Are there plans to release a USB Controller to work with the Planet CNC Output Board for more advanced spindle control from within Planet CNC?

    At this time we are working to release a new USB controller board that will be compatible with Mach4 software and do not have any immediate plans to update the Planet-CNC USB board.

    Click the link to add information to this solution:
    Are there plans to release a USB Controller to work with the Planet CNC Output Board for more advanced spindle control from within Planet CNC?

  • Can I use Mach3 or 4 with your USB controller PCA?

    The USB controller board is currently only compatible with Planet-CNC software.

    Click the link to add information to this solution:
    Can I use Mach3 or 4 with your USB controller PCA?

  • How do you zero the z axis using a plate with the planet-cnc software and your USB controller?

    The instructions on how to use a plate for z-axis homing (moveable sensor) can be found here:

    http://www.planet-cnc.com/faq/moveable_sensor/

    Additional Information:



    Additional Information:



    Additional Information:

    Click the link to add information to this solution:
    How do you zero the z axis using a plate with the planet-cnc software and your USB controller?

  • Using USB Controller Board with Planet-CNC software. The S/W recognizes limit switches but not soft limits. Help?

    "Soft limits are used to decelerate machine to stop before machine is stopped hard way at limit switch or before it crashes. I recommend "Soft Limits Decelerate" and "Soft Limits Strict" settings are also checked. Sometimes we need to disable soft limits and there is a command for this in menu "Machine/Soft Limits". When soft limit is triggered position display will be yellow."

    Are the soft limits "grayed out"?
    Here is a link to a very useful forum post from the Planet-CNC crew:
    http://www.planet-cnc.com/faq/machine_setup/



    Additional Information:
    i keep getting scratches when engraving pictures on dog tags

    Additional Information:



    Additional Information:



    Additional Information:

    Click the link to add information to this solution:
    Using USB Controller Board with Planet-CNC software. The S/W recognizes limit switches but not soft limits. Help?

  • I recently purchased 3 axis electronics with the USB controller board. I'm trying to install an E-stop switch. Where do I connect that on the controller board?

    There are many ways to wire an emergency stop switch. The simplest, and arguably the most certain, way is to wire the switch into the incoming power so that throwing the switch kills all power to every part of the machine. Here is a diagram showing how a customer wired such a switch on their blackTooth laser which you could adapt to your needs. http://www.buildyourtools.com/phpBB3/viewtopic.php?f=12&t=4872

    Alternatively, you could use an input pin on your USB board. The wiring would depend on whether and how you might be using limit switches (single or multiple switches; normally open or normally closed). Our website datasheet for the USB board is at https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout#prettyPhoto/2/ and shows how to configure the switches for each set up. If you use this method, you'd essentially wire the e-stop as a limit switch.

    Click the link to add information to this solution:
    I recently purchased 3 axis electronics with the USB controller board. I'm trying to install an E-stop switch. Where do I connect that on the controller board?

  • I recently purchased 3 axis electronics with the USB controller board. I'm trying to install an E-stop switch. Where do I connect that on the controller board?

    There are many ways to wire an emergency stop switch. The simplest, and arguably the most certain, way is to wire the switch into the incoming power so that throwing the switch kills all power to every part of the machine. Here is a diagram showing how a customer wired such a switch on their blackTooth laser which you could adapt to your needs. http://www.buildyourtools.com/phpBB3/viewtopic.php?f=12&t=4872

    Alternatively, you could use an input pin on your USB board. The wiring would depend on whether and how you might be using limit switches (single or multiple switches; normally open or normally closed). Our website datasheet for the USB board is at https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout#prettyPhoto/2/ and shows how to configure the switches for each set up. If you use this method, you'd essentially wire the e-stop as a limit switch.

    Click the link to add information to this solution:
    I recently purchased 3 axis electronics with the USB controller board. I'm trying to install an E-stop switch. Where do I connect that on the controller board?

  • Hi I have a Proxxon MF70, I want to add 3axis stepper with controller and software by USB. Can you suggest a kit for me? Thanks.

    To implement a electronics combo to run you Proxxon MF70, you will need to find the correct drive components (ACME screw, linear rail, etc) and look into any specific modifications needed to your rig.
    I would recommend the USB 3 Axis Large Motors Electronics w/ USB Interface Board.
    Since the machine is metal, our larger motors would be highly recommended.

    We have not done this conversion, through research is recommended.

    Additional Information:



    Additional Information:



    Additional Information:

    Click the link to add information to this solution:
    Hi I have a Proxxon MF70, I want to add 3axis stepper with controller and software by USB. Can you suggest a kit for me? Thanks.

  • Do you know which BobCAD-CAM post processor works with your USB controller? Do you have a dll or command document to communicate with your USB controller?

    The BobCAD post processor that will work with the USB interface that uses the Planet-CNC software:

    According to the Planet-cnc folks, wincnc or mach3 post-processors should work. According to a representative at BobCAD, mach3 post-processor should work.

    Click the link to add information to this solution:
    Do you know which BobCAD-CAM post processor works with your USB controller? Do you have a dll or command document to communicate with your USB controller?

  • Is there a way to use an X,Y plate that will only be responsible for corner finding in Mach3 with the Mach3 USB controller?

    Yes, you can use a corner plate very easily. You will want to make a corner plate that has three independent plates that do not conduct with each other. Each of these plates will be connected to a different input (i.e. IN1 for X, IN2 for Y and IN3 for Z). The end mill or tool that is inserted into the spindle will connect to V- of the 24V power supply, or the DCM on the controller, which is connected to the 24V V-. Then, you can use the ref all home button on the program run screen of Mach3.

    Click the link to add information to this solution:
    Is there a way to use an X,Y plate that will only be responsible for corner finding in Mach3 with the Mach3 USB controller?

  • Any timing on the USB Controller board for Mach-4

    The board has been developed and we are currently waiting to receive developer info from the makers of Mach4 so we can proceed with testing compatibility. There is no definite time frame but we are hopeful it will be released within the next couple months.

    Click the link to add information to this solution:
    Any timing on the USB Controller board for Mach-4

  • Can I add a relay to the Mach3 USB controller?

    Yes, you can add a relay to the Mach3 USB controller. The relay must be a 24V relay on it's input side and be able to be set to active low. I demonstrate this in a video on the following page:
    https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

    The video is titled: Mach3 USB Controller Outputs

    Click the link to add information to this solution:
    Can I add a relay to the Mach3 USB controller?

Get Help with:
This Product
Orders
Tech Support
Sales
This Product
Order Query
Tech Support
Sales
Not logged in. Log In Register
Track Order(s)
View Order(s)
I Want to Schecule a One-On-One Paid Tech Support Session
Book an Appointment Pertaining to a BuildYourCNC Product (Free)
Ask a Quesion Below (Free):
Book an Appointment Pertaining Other Equipment ($60/half hour)
Book an Immedite Appointment Pertaining Other Equipment ($120/half hour)
Ask a Quesion Below (Free):
Waiting for response... I may not answer immediately, but I was notified on my cellular phone so my response is forthcoming. If I don't respond immediately, you can always go to the [My Account] page to see all of our chats at any time.