It sounds like you got a misprinted book. If you purchased it from us, please contact us directly for a replacement. If you bought it from Amazon or a third party, you'll need to contact them. General information about lead screws is available on this website and at buildyourtools.com.

Click the link to add information to this solution:
Just bought Build Your own CNC Machine book. It is missing the chapter on lead screws that is described on page 181 at the end of Chaprer 16. Where can I get this info?

As long as the bearing has a minimum thickness of 1/4" and 9/32" is a bit thicker, there will be no problem with the book build using the bearing that is 1/32" thicker. There is actually more surface area which is better.

Click the link to add information to this solution:
I am building the CNC in your book - Build you own CNC Machine. One of the bearing thicknesses is 1/4" I can't find that bearing online. I can find 9/32, will that be a problem. Do you have a source? Thx

Gcode or digital files are not available for our machines.

Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
I have the build your own CNC kit 3 Axis CNC Machine 2008, were can I get the Gcode or vector files for it ? I wanted to have it laser cut

You can see the component list on the hardware and plans machine (scratch build machine) since it is the same machine in the book:

https://www.buildyourcnc.com/Item/cnc-machine-scratchbuild

Additional Information:

Click the link to add information to this solution:
I have just brought your build your own cnc machine book and it talks about PDF downloads. Where do I find them please ?

As long as the bearing has a minimum thickness of 1/4" and 9/32" is a bit thicker, there will be no problem with the book build using the bearing that is 1/32" thicker. There is actually more surface area which is better.

Click the link to add information to this solution:
in your book - Build you own CNC Machine. Can I use 9/32" thick bearing instead of 1/4" thick?

You can see the component list on the hardware and plans machine (scratch build machine) since it is the same machine in the book:

https://www.buildyourcnc.com/Item/cnc-machine-scratchbuild

Additional Information:

Click the link to add information to this solution:
I purchase Build Your Own CNC Machine. where can i download PDF so i can print Large

You can see the component list on the hardware and plans machine (scratch build machine) since it is the same machine in the book:

https://www.buildyourcnc.com/Item/cnc-machine-scratchbuild

Additional Information:

Click the link to add information to this solution:
I PURCHASE BUILD YOUR OWN CNC MACHINE. WHERE CAN DOWNLOAD PDF SO PRINT LARGE

The scratchBuild page as listed above (link: https://buildyourcnc.com/cnckitintro.aspx), will have all the necessary hardware (bolts, screws, nuts, washers, etc) to finish the 2' x 4' scratchBuild CNC machine, with a DVD tutorial that will help you along the way.

Please read carefully, some items do not come included in the kit.
Listed materials of items not Included:
Computer of your choice that contains a parallel port
Router of your choice
Sheets of MDF for the structural parts
Aluminum Angles for rails (.75"x.75"x.125").
Lead screws (1/2" allthread/lead screw, or other of your choice). suggested lengths below:
X-Axis: ~52 Inches
Y-Axis: ~32 Inches
Z-Axis: ~14 Inches
Electronics

Click the link to add information to this solution:
I am following the build your own CNC book build for my first machine. Is the hardware on this page https://buildyourcnc.com/item/cnc-machine-scratchbuild the complete hardware kit (minus the items it already noted were not included) required for the build?

You can use either 1" x 1" x 1/8", or 1-1/4" x 1-1/4" x 1/8" angle on the table sides. The BRAs should all be 3/4" x 3/4" x 1/8". The Y ans Z axes should use the 3/4" x 3/4" x 1/8" angles.

Click the link to add information to this solution:
In the Build your own CNC machine book, You said you use 1 1/4" angle on the main table but 1" would be better. So my question is Should I use 1" angle on the main table (4' length) and 1 1/4" angle for the BRA's and other rails?

Yes, the plans are detailed sufficiently enough to produce CAD drawings. If you wish to create AutoCAD drawings from the plans that we provide, we ask that the information conform to the creative commons license established on this site.

Click the link to add information to this solution:
If i can get the autocadd drawings of the building mdf peices that need to be build are the plans detailed enough for me to make my own autocadd drawings? I have access to another machine to build my own.

For our machines our steps for the build process can be found on the actual machine page with images to reference (please read carefully all the instructions) (https://www.buildyourcnc.com/blackToothLaserCutterAndEngraver.aspx).
You can get further help here (http://blacktoothlaser.blogspot.ca/2013/04/index-for-blacktooth-laser.html?view=sidebar) a post made by one of our customers!

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
where is the build manual for the blacktooth laser? online? I didnt get one with my machine

Using Anti-Freeze in the cooling system with either our spindle or our laser tubes will not have any problems and we recommend using a small amount in locations where temperature is freezing or below.
Although we do not recommend using an entire gallon of anti-freeze rather just a small quantity with tap water will be sufficient.

Additional Information:


Additional Information:
All last winter, the temperature was below freezing and sometimes below zero. I used 100% antifreeze for the spindle coolant. Worked great !! All the spindle needs is any type of coolant flowing through it to take the heat away. I use three gallons of antifreeze in a tub with a fish-tank pump to push the antifreeze through. 100% antifreeze works great in cold or hot winter.

Additional Information:
Excellent tip. Thank you for this correction. So it is OK to use antifreeze solely as a cooling method.

Click the link to add information to this solution:
Can anti-freeze be used as a coolant for your 40W laser tube? I live where winter temperatures are below freezing and my CNC machine is in my unheated garage.

The book (scratch build) will be able to cut at very high rates of speed, but the speed is partly determined by the mechanical setup. Cutting wood is generally recommended between 60-200 ipm depending on the end mill and spindle being used. The larger the end mill (with increased chip load capacity) the faster the feedrate.

If you are using a standard allthread, you will not be able to have these high feedrates. You will need to purcahse high lead leadscrews: https://www.buildyourcnc.com/item/mechanical-leadscrews-leadnuts-!5-5-starts-10-tpi

The stepping motors need to turn 13 times to travel one inch using standard allthread (1/2-13 TPI - threads per inch). The higher lead leadscrews shown in the link provided will move one inch with only two turns allowing the machine to move many times faster.

These speeds are especially important if you are cutting materials that have low melting points like aluminum and thermoplastics like acrylic, Plexiglas, etc. These materials require high feedrates and smaller depth per passes.

Additional Information:
20

Click the link to add information to this solution:
I just made the book build Cnc machine with the feed rate of 11.19 inch/min as suggested in book. Can I increase it to 20 inch/min? I have 2hp of router attached

The motor is helped by the mechanical leverage of the screw. The 425 oz-in motors that are included in the standard electronics combo has very high torque for that type of machine. You will have no problem using that motor for the book machine.

We use that motor for very heavy spindles on the blackToe and blackFoot CNC Machine kits.

You will need to do the mechanical leverage calculation along with the torque of the motor to determine the actual weight it will lift. The calculation will need to consider the type and pitch of the screw and it would also consider the gravity constant of 9.8 m/s/s.

If you need me to determine this formula and work out the calculation based on the screw you are using, please let me know.

Additional Information:
thank you for the reply. I would be really good to know the calculation. The lead screw is 1/2" diameter with 13 TPI. Please provide the calculation. And one more question. If I am cutting 18mm MDF with 6mm cutting bit (so 6mm pass), what can be the maximum speed rate of cutting and spindle speed of router?
thank you

Click the link to add information to this solution:
I received the electronics for book build cnc machine. I need to know how much weight the z-axis motor can hold since my (craftsman) router seems to be heavy. It is 2HP with variable speed

If you're talking about the anti-backlash nut, ou can find replacements on our website here: https://buildyourcnc.com/CNCMachineMechanicalParts.aspx and here: https://buildyourcnc.com/CNCMachineMechanicalParts.aspx. If you have something else in mind, please contact us to further describe the part you need.

Click the link to add information to this solution:
I own a BlackToe cnc machine. The plastic threads with the spring over them broke. Where can i purchase a replacement part?

We are developing plans for our machine, but they are not completed yet. Please let me know if you would like to be added to our list of customers wanting plans. Thanks,

Additional Information:
If you have specific questions regarding CAD, CAM and Control, please add another question to the customer service and I will answer them in detail.

Click the link to add information to this solution:
How do I get started I would like to build a cnc router. Making the machine I can do, but I am weak on cad,cam and mach3. I am thinking about a 4’x4’. Do you have plans I can buy?

The electronics (stepper motors, drivers, power supply and interface board) can be found here:
https://www.buildyourcnc.com/item/electronicsAndMotors-3axis-425-elcombo

If your computer cannot connect to the parallel breakout board (the interface card), just make sure to inform us that you need the USB alternative.

Click the link to add information to this solution:
Just purchased the book "Build Your Own CNC Machine". Can I get hardware and electronics kits and how?

The largest CNC machine we make at this time (12/04/2015) is the GreenBull 6'x12' model. This model has 2 options for Z-axis travel.

The short-z option has a total Z travel of 5.75 inches. From that you would subtract the length of the end mill used and the thickness of the spoil board to determine the maximum material thickness. (Example: If the end mill extends 1.25" from the collet and the spoil board is .75", then the material could be up to 5.75 - 1.25 - 0.75 = 3.75 inches in thickness). This is good for most sheet-type materials.

The long-z option, used mainly for large 3D carvings, requires a custom frame and allows for up to 36" of travel.

The tolerance of our machines, like any machine, depends on several variables. The major variables include the manufacturing tolerance, the type of machine control used, the precision of assembly, the thoroughness of maintenance, and the initial and ongoing calibration of the machine. Because we sell kits only most of these variables are outside our control. Therefore, we are hesitant to guarantee a certain level of tolerance for an end user. However, in our experience, tolerances of .001" are readily achievable with our machines.

Additional Information:

Click the link to add information to this solution:
What tolerance can I expect from your largest cnc machine and the laser cutter? Also, what depth can I get on the z axis?

We would highly recommend using our forums to sell you machine buildyourtools.com.
We currently do not have a page or option to allow our customers to sell our machines, you can also contact us at customerservice@buildyourcnc.com, for further assistance dealing with the machine and in regards to selling it.

Click the link to add information to this solution:
I have a blueChick 13"x24" or 13"x36" Desktop CNC Router Kit v3.0 (Timing Belt) that I've assembled but never was able to get it running. Can BuildYourCNC assist me in selling this machine? Do you have used machine offerings on your site?