You can see the component list on the hardware and plans machine (scratch build machine) since it is the same machine in the book:

https://www.buildyourcnc.com/Item/cnc-machine-scratchbuild

Additional Information:

Click the link to add information to this solution:
I purchase Build Your Own CNC Machine. where can i download PDF so i can print Large

You can see the component list on the hardware and plans machine (scratch build machine) since it is the same machine in the book:

https://www.buildyourcnc.com/Item/cnc-machine-scratchbuild

Additional Information:

Click the link to add information to this solution:
I have just brought your build your own cnc machine book and it talks about PDF downloads. Where do I find them please ?

If you're talking about the anti-backlash nut, ou can find replacements on our website here: https://buildyourcnc.com/CNCMachineMechanicalParts.aspx and here: https://buildyourcnc.com/CNCMachineMechanicalParts.aspx. If you have something else in mind, please contact us to further describe the part you need.

Click the link to add information to this solution:
I own a BlackToe cnc machine. The plastic threads with the spring over them broke. Where can i purchase a replacement part?

The specifications for the book build can be found on the flowing URL: https://www.buildyourcnc.com/Item/cnc-machine-scratchbuild

Click the link to add information to this solution:
Where can I get the spec for the Cnc machine for the machine in the book build your own Cnc machine I tried the web page but no mesurments that I found

It sounds like you got a misprinted book. If you purchased it from us, please contact us directly for a replacement. If you bought it from Amazon or a third party, you'll need to contact them. General information about lead screws is available on this website and at buildyourtools.com.

Click the link to add information to this solution:
Just bought Build Your own CNC Machine book. It is missing the chapter on lead screws that is described on page 181 at the end of Chaprer 16. Where can I get this info?

As long as the bearing has a minimum thickness of 1/4" and 9/32" is a bit thicker, there will be no problem with the book build using the bearing that is 1/32" thicker. There is actually more surface area which is better.

Click the link to add information to this solution:
in your book - Build you own CNC Machine. Can I use 9/32" thick bearing instead of 1/4" thick?

Unfortunately we no longer include or sell our CNC plans for none of our machines. We will be here to assist you if any parts wear over time, and will be able to replace the parts if needed.

Charges may be subjected due to time of purchase and cause of wear.

Click the link to add information to this solution:
Can I purchase plans to scratch build the Blackfoot or GreenBull machine

Gcode or digital files are not available for our machines.

Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
I have the build your own CNC kit 3 Axis CNC Machine 2008, were can I get the Gcode or vector files for it ? I wanted to have it laser cut

You can see the component list on the hardware and plans machine (scratch build machine) since it is the same machine in the book:

https://www.buildyourcnc.com/Item/cnc-machine-scratchbuild

Additional Information:

Click the link to add information to this solution:
Just want to know where could I download the CNC machine spreadsheet and the Parts Layout PDF files. Had tired www.buildyourcnc.com/book.aspx but was unable to locate the said files.

As long as the bearing has a minimum thickness of 1/4" and 9/32" is a bit thicker, there will be no problem with the book build using the bearing that is 1/32" thicker. There is actually more surface area which is better.

Click the link to add information to this solution:
I am building the CNC in your book - Build you own CNC Machine. One of the bearing thicknesses is 1/4" I can't find that bearing online. I can find 9/32, will that be a problem. Do you have a source? Thx

Using Anti-Freeze in the cooling system with either our spindle or our laser tubes will not have any problems and we recommend using a small amount in locations where temperature is freezing or below.
Although we do not recommend using an entire gallon of anti-freeze rather just a small quantity with tap water will be sufficient.

Additional Information:


Additional Information:
All last winter, the temperature was below freezing and sometimes below zero. I used 100% antifreeze for the spindle coolant. Worked great !! All the spindle needs is any type of coolant flowing through it to take the heat away. I use three gallons of antifreeze in a tub with a fish-tank pump to push the antifreeze through. 100% antifreeze works great in cold or hot winter.

Additional Information:
Excellent tip. Thank you for this correction. So it is OK to use antifreeze solely as a cooling method.

Click the link to add information to this solution:
Can anti-freeze be used as a coolant for your 40W laser tube? I live where winter temperatures are below freezing and my CNC machine is in my unheated garage.

I just added a link to the Mach3 license page on our site:
https://www.buildyourcnc.com/item/control-SOFTWARE-mach3

Click the link to add information to this solution:
I look on your site and find nowhere to download Mach 3, Where is it?

As you know, the plasma nozzle must be close to the cutting area and you will need some way to keep the nozzle at the right level with some type of device. The spray is downward, so you will need a contained area with a sheet of water at the bottom to extinguish he spray. You should have no problem using our machines for this application since you would need to product the table bed.

Click the link to add information to this solution:
DO WE CAN BUILD OUR CNC MACHINE WITH TOW TORCHES (PLASMA TORCH & OXY ACETYLENE TORCH)?

Yes, I will need to know more specifics of the machine so I can recommend the correct electronics.

Click the link to add information to this solution:
ok I Build my CNC machine table and now need a complete set for motor and software how you can help me

We offer as much information as possible about the design and building of CNC machines through this website and the forums at buildyourtools.com. We also still offer our "scratch build" plans at https://buildyourcnc.com/item/cnc-machine-scratchbuild, where you can order the plans and DVD to build your own machine with or without the necessary hardware components.

Our technical support staff are occupied full time assisting customers who have bought complete kits or assembled machines, and unfortunately do not have the resources to provide one-on-one advice to individuals.

Click the link to add information to this solution:
I Want to design and build my own CNC wood working machine. Do you give advice and help advice to do this?

For our machines our steps for the build process can be found on the actual machine page with images to reference (please read carefully all the instructions) (https://www.buildyourcnc.com/blackToothLaserCutterAndEngraver.aspx).
You can get further help here (http://blacktoothlaser.blogspot.ca/2013/04/index-for-blacktooth-laser.html?view=sidebar) a post made by one of our customers!

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
where is the build manual for the blacktooth laser? online? I didnt get one with my machine

We haven't really searched for metric lead screws and nuts. I tried doing a cursory search for metric sized lead screws and nut with your specification of 12mm from the previous question and found it quite challenging. If you can't find the correct anti-backlash nut, I would recommend getting a 1/2" lead screw and anti-backlash nut and change your coupling to a 1/2" for the lead screw side and the bearings to 1/2" ID bearings.

Click the link to add information to this solution:
Where can I purchase metric anti-backlash nuts as I live in Australia?

You will need to build the table unit for your machine. There are instructions on how to do this at the bottom of the product page here, https://www.buildyourcnc.com/Item/cnc-machine-blackFoot-v4
There is no estimate on how much this will cost though, since there are too many variables involved to do this.

- PC with parallel port and USB port
- 20awg stranded wires for the motors - http://www.buildyourcnc.com/electronicscombo.aspx
- 18awg stranded wires for power supply to drivers
- 24awg stranded wires for breakout board to drivers
(location and spacing of components varies from one person to another, so we do not provide cables/wires)
- General purpose extension cord (cut the female end off) to provide power to power supply
- USB cable to power breakout board
- Parallel cable to communicate to breakout board
- Router
- (optional - instead of router) Spindle with power inverter http://www.buildyourcnc.com/SpindlesAndAccessories.aspx
- (if purchasing spindle with inverter) General purpose extension cord (240v) (cut the female end off) to provide power to power inverter
- End Mill(s) http://www.buildyourcnc.com/ProductsEndMills.aspx
- CAD, and/or CAD-CAM software (to produce geometry, machine operations, and g-code) http://www.buildyourcnc.com/CNCsoftware.aspx
- CNC control software (to read g-code and control machine) http://www.buildyourcnc.com/CNCsoftware.aspx

This answer is applicable to most of our machines with the exception of the greenLean and the blueChick since those machines are equipped with a table structure.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
Can I purchase a computer off Amazon (I have a machine I want to use) and still use the USB interface to drive it with LinuxCNC?

If you would like to come to the office, please call the office at 281-815-7701 to request a visit at your specified time within our business hours so we can make sure that the right person will be there to assist you.

Click the link to add information to this solution:
Can I visit your shop and purchase a BOB and 5/8 coupling ? I live in Houston.