It sounds like you got a misprinted book. If you purchased it from us, please contact us directly for a replacement. If you bought it from Amazon or a third party, you'll need to contact them. General information about lead screws is available on this website and at buildyourtools.com.

Click the link to add information to this solution:
Just bought Build Your own CNC Machine book. It is missing the chapter on lead screws that is described on page 181 at the end of Chaprer 16. Where can I get this info?

Since this 4th axis already comes with a stepper motor, you will need a driver and some cable to connect to the driver from where the 4th axis will be placed. If you have extra space in the redFly electronics enclosure, you can fasten the driver there. You will also need some wire to connect the driver to the breakout baord.

Click the link to add information to this solution:
[410] what I need to buy to make this work on my GreenBull machine and the redfly?

Yes, I will need to know more specifics of the machine so I can recommend the correct electronics.

Click the link to add information to this solution:
ok I Build my CNC machine table and now need a complete set for motor and software how you can help me

Yes, we can make a redLeaf system that has all 6A drivers for use with the 651 oz-in motors. We can also wire the electronics in a way that two of the drivers will use the pins of the same axis so that axis will drive two drivers and motors.

Click the link to add information to this solution:
I am building a machine that requires 2 steppers to drive the Y axis, can you make me a redleaf system using the 651oz steppers that will work for me?

The eyebolts are used in the squaring of the machine. I would use a standard carpenters square and first run the end mill along the edge of the square to first make it parallel with the long axis. Then run the end mill along the other edge with the short axis and adjust the eye bolts and chain according to the angle that the machine is out of square.

Additional Information:

Click the link to add information to this solution:
DO NEED TO SQUARE UP THE MACHINE AND IF SO YOU HAVE INSTRUCTIONS OR VIDEO FOR THIS?

That is a very loaded question that could be replied in so many ways. I will need a more specific question to help you. For instance, I have my machine moving in different directions, but I don't know how to make the machine move according to g-code instructions. Another question could be, I connected all of my electronics and the motors are not moving and I did all of the steps on the electronics video to troubleshoot the problem.

Click the link to add information to this solution:
I have a cnc router that was built from the book "Build your own cnc machine" by james kelley and patrick hood daniel.all the parts were purchased from your company.I have no clue how to work the machine and I need to purchase a spindle (or router) bits , softwear ect , I did mention I don't know how to use the machine !!! Thanks for your help Richard

Consider the loads on each axis when choosing appropriate stepper motors. If your holding torque is maxed out at roughly 16oz/in (1lb/in), then you could use the NEMA 11 or 14. Also consider the shaft sizes and current ratings when choosing drivers that pair with the motors.

Click the link to add information to this solution:
I am planning to build a scratch CNC machine to do rotary engraving on writing pens. Can you recommend the parts I would need? I'm thinking NEMA 14 (11?) and 3/8" acme rod. Not sure which linear motion to use. I have an old lathe to use for the 4th axis.

The greenBull 4X comes with all of the components and electronics to assemble the gantry of the machine. You will need to build the table. We provide the rails and roller chain for the X-axis (along the length of the table for full 8 feet of travel). You will need to provide some wire to connect the electronics and a computer to run the machine. You will also need to purchase the software that you will need to run the machine that matches how you will apply the machine. We suggest the mach3 control program. The CAM program is up to you as there are many options out there.

Click the link to add information to this solution:
I am interested in buying the greenBull 5X Long Z CNC Machine Kit, but it is not clear for me what is included in this kit. Is there anything else I need to get the machine work?

That will depend on the controller that was installed in the redFly. If the controller is a pokeys57CNC controller, you can use Mach 4 with that system.

You can add a 4th axis and an ATC (Automatic Tool Changer) with the redFly system.

Click the link to add information to this solution:
Does the Redfly that I bought with the GreenBull in 2016 work with Mach4? Also I want to add a 4th axis and a spindle with automatic tool changer. Will this work too or do I need a new control board? I bought my CNC with a longer Z travel, so I have plenty of room for these. Thanks!

I would recommend using the blackToe CNC machine kit. The overall travel dimensions are 24" x 48" x 6". This will provide a bit of space on the sides as wiggle room if your guitar bodies are at the extremes of the 12". Also, if you are manufacturing may of these, the larger routing area, the more guitar bodies you will be able to cut at one time.

Click the link to add information to this solution:
I need a machine to cut guitar bodies. The bodies are 12" x 16" and 1.5" thick. What would work best?

Yes, you can contact me at customerservice@buildyourcnc.com to get the full BOM for that machine.

Click the link to add information to this solution:
I have a green lean machine that I acquired from a friend that had to move cross country and could not take the machine with him. It was partially disassembled and stored in his garage. Unfortunately, he lost a couple of parts I cannot easily replicate. Is there a parts list anywhere for this machine so that I can order replacements?

Ok, sure. Let's get the discussion started. Please respond with your questions on this FAQ

Click the link to add information to this solution:
Hi, I am thinking of making a CNC router that I can use in woodworking. I am very happy if you can help me with the necessary parts for this

BYCNC Response:
This is correct. You will need to use a method appropriate for the software you are using. Also remember that NC switches are typically wired in series, while NO switches are normally wired in parallel.

User Response:
I am using the cnc planet software for your USB board. Are the limit configurations in this software?

BYCNC Response:
Yes, Planet CNC software is compatible with the use of limit switches. Configuration information will depend on your specific application. You can view Planet CNC's information here: http://www.planet-cnc.com/files/CNCUSBController.pdf

Click the link to add information to this solution:
LIMIT SWITCHES FOR AXIS. THE PRINT SHOWS THAT YOU CAN WIRE LIMITS EITHER N.O. OR N.C. SO IF THIS IS CORRECT I WOULD NEED TO TELL BOARD IN SOFTWARE HOW LOOK AT THESE LIMITS, I'M GOING GET AN INPUT LOOSE DEPEND ON IT.

The largest cutting area machine we have available is our greenBull 6X, which allows a cutting surface of 6' x 12'. The limit of our machines is the x-axis being the width, but you can elongate the machine as far as you require, being 15 Ft. or more.
I would highly recommend a visit to our R&D page, which allows you to post ideas/requests and to view the current tasks that we are working on!

Click the link to add information to this solution:
I work with carpet & padding and need to cut carpet to create clean 90 degree corners, and patterns for inlay's. The work area would need to be a minimum of 12 ft by 15 ft. Is there an affordable kit that could accommodate this size

Could you specify which breakout board you have? If you have a parallel port version, be sure that you have purchased the "legacy" parallel port version from Mach4. If this proves not to be the problem, please feel free to email us directly at techsuport@buildyourcnc.com or call 281-815-7701 for troubleshooting instructions.

Click the link to add information to this solution:
I need a resource, we bought 2 redfly systems and mach 4, We put one motor on for the x axis but cannot get it move. Can you direct us to some tutorial?

I need programing help not wiring help. Speed will only go to 50.

You can find the inverter (VFD) manual at: https://buildyourcnc.com/Documents/HuanYang_inverter_manual.pdf

If you have further questions, please enter your question here by submitting additional information.

Click the link to add information to this solution:
I called a little bit ago for a copy of the inverter manual. I really need this infor. thank you

Are you using the control panel (front panel with the speed control knob known as he potentiometer)? Or are you attempting to use the computer to control the speed?

Additional Information:
I am using the control panel, however there is no knob on mine, just buttons.

Click the link to add information to this solution:
Hello, I bought your 110v 2.2kw spindle and vfd. When I turn it on it reaches the full 24000 rpm, but will not let me decrease the speed. How Can I fix this?

Modifying the Z-axis to accommodate a larger motor will be a worth while task and is possible, however we have not calibrated the z-axis therefore using the 1600 Steps-per inch in the motor tuning on our machine in our shop. We have not noticed any significant depth increments from not calibrating the z-axis but only from zeroing the z axis too close to the material. Also in your design did you specify the actual depth and the length of tool (end mill/ bit) that you are using?

Click the link to add information to this solution:
I bought a Blacktoe 2 x 8 three years ago and have always had a problem with the Zid axis. No matter how tightly I've calibrated the axis it always cuts to deep. Can I put a larger Stepper motor on Z-axis using the same motion electronics that came with the original machine.

We have sent machines everywhere across the globe and we can work with freight companies to get you a good rate on a shipment. Please email sales@buildyourcnc.com to request a quote.

Click the link to add information to this solution:
Im from chile have you ever send any machine to south america? can i buy only the mechanic and electronic things ( wood parts are much weight)