I have a green lean machine that I acquired from a friend that had to move cross country and could not take the machine with him. It was partially disassembled and stored in his garage. Unfortunately, he lost a couple of parts I cannot easily replicate. Is there a parts list anywhere for this machine so that I can order replacements?

Question #: 14515

Question: I have a green lean machine that I acquired from a friend that had to move cross country and could not take the machine with him. It was partially disassembled and stored in his garage. Unfortunately, he lost a couple of parts I cannot easily replicate. Is there a parts list anywhere for this machine so that I can order replacements?

Current Solution

Yes, you can contact me at customerservice@buildyourcnc.com to get the full BOM for that machine.

Respond:

Other Possible Solutions to this Question

Hello, My friend has purchased the Redfly and I am helping him a little with it. We are both very new to CNC. I am using fusion 360 at the moment. This can tool path and create gcode. I was wondering if Mach 3 or similar is still needed. Is there a tutorial you could point me to that explains how to get the Gcode from the PC, via Serial to the Redfly?
Fusion 360 is a program that allows you to design in a parametric 3 dimensional environment and also provides a great CAM toolset. Fusion 360 will produce the gcode with the CAM capabilities. The gcode is used to move the machine in various ways in order to mill the material; however, software is needed to interpret this gcode and cause the machine to move according to the gcode instructions. This is called control software. So Fusion is CAD/CAM, and you still need "control". Mach3 is one example of control software for milling and is highly recommended.

Install Mach3 onto the computer that will connect to the redFly(CNC electronics), then configure the Mach3 parameters for the machine (motor tuning, plug-ins, inputs/output, etc.). Home the machine, load the gcode into Mach3 and the machine will move according to the gcode.

A word of caution, since you are new to CNC machines, make sure you familiar yourself with the machine and the movements of the machine specific to how the gcode is arranged with respect to the coordinates of the machine. Try with very simple gcode until you get a very good understanding of how the machine will move.
Click the link to add information to this solution:
Hello, My friend has purchased the Redfly and I am helping him a little with it. We are both very new to CNC. I am using fusion 360 at the moment. This can tool path and create gcode. I was wondering if Mach 3 or similar is still needed. Is there a tutorial you could point me to that explains how to get the Gcode from the PC, via Serial to the Redfly?
How can I get a replacement part for my Green Lean machine that i cant order from the Stuff For Sale page? I need the bearing truck plate for the Constant Force Spring. Or is there someplace I can get a drawing of the part so that I can make one?
I can provide a drawing for that part or I can sell you the part of the machine that you need. Just email me at customerservice@buildyourcnc.com with a description of the part you need.
Click the link to add information to this solution:
How can I get a replacement part for my Green Lean machine that i cant order from the Stuff For Sale page? I need the bearing truck plate for the Constant Force Spring. Or is there someplace I can get a drawing of the part so that I can make one?
Hello, I have a BlackToe 2 x 4 machine. I was wondering if it could be beneficial, or even possible to install two motors on the x-axis (one one each chain drive sprocket). I am noticing a slight shift in the gantry with each reversal of direction. If so, do you have a kit or schematic for this? Thanks
it is possible to install 2 motors on a single axis but you will require another driver and motor, but wire it directly to the same pins on your breakout board. Also the orientation of your motor since it is opposite side of the original so getting it to move accordingly to the original motor it will need to be orientated correctly. The slight shift could be the cause of the rod not being completely flat where the set screws are suppose to tighten the sprocket to the rod, so sanding it to a flatter surface might fix the shift in directions.
Currently do not have a kit or schematic available.
Click the link to add information to this solution:
Hello, I have a BlackToe 2 x 4 machine. I was wondering if it could be beneficial, or even possible to install two motors on the x-axis (one one each chain drive sprocket). I am noticing a slight shift in the gantry with each reversal of direction. If so, do you have a kit or schematic for this? Thanks
How can I decrease the rapid acceleration of the cutter from a completed cutting operation to a new location so that the stepper motor will not lose its steps and mess up the machine zero settings? I am using CamBam and Mach3 on my machine with a chain drive. what is the best way to reduce accleration
Decreasing the speed of acceleration in the cutter? Meaning of your router/spindle?, To modify the speed of a router will be going to the router itself and modifying the speed, but if a spindle is being used modifying it will be done either manually in the VFD (VFD Setup:
Change PD001 to '0' (source of run commands)
Change PD003 to 300 (main frequency - Hz)
Change PD004 to 300 (base frequency - Hz)
Change PD005 to 400 (max operating frequency - Hz)
Change PD006 to 2.5 (intermediate frequency - Hz)
Change PD008 to 220 (max voltage - V)
Change PD009 to 15 (intermediate voltage - V)
Change PD010 to 8 (minimum voltage - V)
Change PD011 to 100 (frequency lower limit - Hz)
Change PD142 to 7 (rated motor current - Amps)
Change PD143 to 2 (motor pole number)
Change PD144 to 3000 (rated motor revolution))<- make sure these are your settings in the VFD. If the spindle is wired to the breakout board and is working through Mach 3 then the modification will be done in your CamBam/Feed rate settings.
Click the link to add information to this solution:
How can I decrease the rapid acceleration of the cutter from a completed cutting operation to a new location so that the stepper motor will not lose its steps and mess up the machine zero settings? I am using CamBam and Mach3 on my machine with a chain drive. what is the best way to reduce accleration
Hello, I have a blacktooth laser cutter, the machine has 10hrs of work, suddenly in the middle of a job the laser beam lost all power, I can still se the purple plasma beam but with no power or intensity, the tube is fine, water is running through and there is no arcing to the chasis or some other part. I think it might be a faulty PS how can I test it, Do I have a warranty on it?
To verify, you are still getting the laser tube to fire, but the laser beam is weak and cannot cut or engrave any materials correct?

Have you checked your tube's tungsten post terminals to make sure they are getting good contact?
The Laser tube and laser power supply both have manufacture warranty, please email customerservice@buildyourcnc.com for further assistance.
Click the link to add information to this solution:
Hello, I have a blacktooth laser cutter, the machine has 10hrs of work, suddenly in the middle of a job the laser beam lost all power, I can still se the purple plasma beam but with no power or intensity, the tube is fine, water is running through and there is no arcing to the chasis or some other part. I think it might be a faulty PS how can I test it, Do I have a warranty on it?
I recently purchase the BlackToe v2.1 (4x8) at a local school auction. The table is complete, however, it is missing the spindle and came in 4 (four) separate pieces. Are there plans for this machine that I would be able to use to reconstruct and determine if anything else is missing.
Yes, you can find all of the instructions for the blackToe CNC Router here:
https://buildyourcnc.com/item/cnc-machine-blacktoe-v4-2x4
Click the link to add information to this solution:
I recently purchase the BlackToe v2.1 (4x8) at a local school auction. The table is complete, however, it is missing the spindle and came in 4 (four) separate pieces. Are there plans for this machine that I would be able to use to reconstruct and determine if anything else is missing.
I was in the process of aligning mirrors for our vertical XL and suddenly the laser does not fire anymore, there is an arcing sound and a light near the Anode (positive) connector of the tube on the very inside. Do you think the laser tube would go bad so quickly? how could we avoid this?
Can you check if there are cracks in the inner glass tube? Also, check to see if there is water between the inner glass tube and the outer glass tube. That will give you an indication of cracking in the inner glass tube.
Click the link to add information to this solution:
I was in the process of aligning mirrors for our vertical XL and suddenly the laser does not fire anymore, there is an arcing sound and a light near the Anode (positive) connector of the tube on the very inside. Do you think the laser tube would go bad so quickly? how could we avoid this?
I purchased the original instructions about 3 years ago and successfully built that device. Now I am looking at the 13X36 Bluechick base kit. Will all my original electronics work with the new kit? Is there a parts list that you could send me for the 13x36 Kit?
Depending on the type of motors and connection type, you could adapt your motors to work with our electronic packages, but you will receive additional motors since our kit is complete.

Now you will have to take into affect the actual motors you have and compare or get accurate replacements(Ex. our 425 oz motor(1/4" input shaft) will have to be same size or similar entry holes)

Your Controller board will be the major issue, due to its wiring and processing manner, you can view the connections for our breakout boards to compare with yours! (parallel: https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay#prettyPhoto/2/)(USB: https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout#prettyPhoto/2/)
Email(customerservice@buildyourcnc.com for further help)
Click the link to add information to this solution:
I purchased the original instructions about 3 years ago and successfully built that device. Now I am looking at the 13X36 Bluechick base kit. Will all my original electronics work with the new kit? Is there a parts list that you could send me for the 13x36 Kit?
I bought a 'BuildyourCNC V1' relay board to go with my mach3 usb controller. I have been sent a 'Songle' relay. It's not the one in your picture and it's got different connections, for which there isn't a wiring diagram. The one I ordered says it is 5v, this one seems to be saying it's a 24v unit. Can you please explain what has happened? Thanks
The Mach3 USB interface board requires 24V relays externally. There are no relays on the mach3 usb board. If you use an external relay on the mach3 usb board, the relay connects to the V+ which is 24V and the output pin is the return.

Additional Information:
I understand what you are saying. Does your relay board work with the Mach3 USB board? If not, what relay board do you suggest to work with this usb controller?

Additional Information:
Our relay board works with our parallel breakout board. An off the shelf SSR (Solid State Relay) made for 24V should work fine.
Click the link to add information to this solution:
I bought a 'BuildyourCNC V1' relay board to go with my mach3 usb controller. I have been sent a 'Songle' relay. It's not the one in your picture and it's got different connections, for which there isn't a wiring diagram. The one I ordered says it is 5v, this one seems to be saying it's a 24v unit. Can you please explain what has happened? Thanks
I bought a 'BuildyourCNC V1' relay board to go with my mach3 usb controller. I have been sent a 'Songle' relay. It's not the one in your picture and it's got different connections, for which there isn't a wiring diagram. The one I ordered says it is 5v, this one seems to be saying it's a 24v unit. Can you please explain what has happened? Thanks
The Mach3 USB interface board requires 24V relays externally. There are no relays on the mach3 usb board. If you use an external relay on the mach3 usb board, the relay connects to the V+ which is 24V and the output pin is the return.

Additional Information:
I understand what you are saying. Does your relay board work with the Mach3 USB board? If not, what relay board do you suggest to work with this usb controller?

Additional Information:
Our relay board works with our parallel breakout board. An off the shelf SSR (Solid State Relay) made for 24V should work fine.
Click the link to add information to this solution:
I bought a 'BuildyourCNC V1' relay board to go with my mach3 usb controller. I have been sent a 'Songle' relay. It's not the one in your picture and it's got different connections, for which there isn't a wiring diagram. The one I ordered says it is 5v, this one seems to be saying it's a 24v unit. Can you please explain what has happened? Thanks
I purchased your book to build a cnc router, the plan drawings are indecipherable and text with them is illegible. There is a note to refer to MDF Parts Layout 1 PDF, MDF Parts Layout 2 PDF and MDF Plans & Cut List PDF downloadable from this site. Where are they I can't find them?
Looks like you are trying to screw me out of $30 plus tax as there will be no pdf files forthcoming unless I shell out another $255. Unless you provide the pdf files I will be forced to seek return of funds and will be notifying VISA, GOOGLE PLAY and the BBB doing so until I get satisfaction. If you are not going to honor your book title by providing complete usable information you should remove your book from the market place, or offer it for free. At this point I don't know how you justify screwing your customers like this, but this one ain't going to take it laying down.

Additional Information:
Official Buildyourcnc response:
Thanks for informing us of this issue. Have you looked at this part of the wabsite:
https://www.buildyourcnc.com/Book.aspx

The link to the "book" portion of the website is in the footer of every page of the website. If there is a problem with the pdf documents on any page of this portion of the website, please let me know here. Many thanks, Patrick Hood-Daniel
Click the link to add information to this solution:
I purchased your book to build a cnc router, the plan drawings are indecipherable and text with them is illegible. There is a note to refer to MDF Parts Layout 1 PDF, MDF Parts Layout 2 PDF and MDF Plans & Cut List PDF downloadable from this site. Where are they I can't find them?
X AXIS STEPPER MOTOR STALLS AND SHUTTERS WHEN COMING FROM A STAND STILL WON'T MOVE WITHOUT PUSH BY HAND. I TOOK THE CHAINS OFF SPUN FINE WITH OUT LOAD. HAVE CHAIN HOOKED UP CAN MACHINE BACK FORTH HAND, NO HANG UPS OR ANYTHING, BUT TRY TO IT DOESN'T JUST SPINS OUT. ANY SUGGESTIONS?
If your axis shutters and will not move unless moved by another force, that sounds like your acceleration is set too high. Lower the acceleration until it works well, then lower it a bit more to have a margin of safety.

IF that didn't work, try swapping the X and Y drivers. That way you will pinpoint if the issue is the driver. If the proplem persists, then there may be an issue with the motor itself.

The X and Y drivers can be easily swapped by swapping only the motor wires.

- Remove the x-axis motor wires from the X driver.
- Remove the Y motor wires from the Y driver.
- Insert the X motor wires into the Y driver.
- Insert the Y motor wires into the X driver.

Now the Y-axis will move the gantry. Test the Gantry movement by moving the Y axis using the up and down arrow keys (mach3).
Click the link to add information to this solution:
X AXIS STEPPER MOTOR STALLS AND SHUTTERS WHEN COMING FROM A STAND STILL WON'T MOVE WITHOUT PUSH BY HAND. I TOOK THE CHAINS OFF SPUN FINE WITH OUT LOAD. HAVE CHAIN HOOKED UP CAN MACHINE BACK FORTH HAND, NO HANG UPS OR ANYTHING, BUT TRY TO IT DOESN'T JUST SPINS OUT. ANY SUGGESTIONS?
I am trying to purchase a kit for our school in Singapore, and your site keeps refusing our corporate AMEX card. Can you help us figure out what is up with that? Are you not ship to Singapore or something? Our AMEX rep says that the account is authorised for this purchase from our end, so the problem may be with your site? Please advise.
Please contact us at sales@buildyourcnc.com so we can provide you with assistance on your order
Click the link to add information to this solution:
I am trying to purchase a kit for our school in Singapore, and your site keeps refusing our corporate AMEX card. Can you help us figure out what is up with that? Are you not ship to Singapore or something? Our AMEX rep says that the account is authorised for this purchase from our end, so the problem may be with your site? Please advise.
Can you install a more powerful laser/tube for us if we pick the $2100 option to have you build it? It would be assumed that there would be a new price for the machine which would reflect the cost increase for the new laser. Please say yes, I know you can physically do it. I have faith in you
The space allotted for the laser tube on the blackTooth would not allow for a higher power laser tube. As the wattage of the laser tube increased, so does the length of the tube.

We do have a larger and more powerful laser in design and should be available in the second quarter of 2015.
Click the link to add information to this solution:
Can you install a more powerful laser/tube for us if we pick the $2100 option to have you build it? It would be assumed that there would be a new price for the machine which would reflect the cost increase for the new laser. Please say yes, I know you can physically do it. I have faith in you
I bought a Blacktoe 2 x 8 three years ago and have always had a problem with the Zid axis. No matter how tightly I've calibrated the axis it always cuts to deep. Can I put a larger Stepper motor on Z-axis using the same motion electronics that came with the original machine.
Modifying the Z-axis to accommodate a larger motor will be a worth while task and is possible, however we have not calibrated the z-axis therefore using the 1600 Steps-per inch in the motor tuning on our machine in our shop. We have not noticed any significant depth increments from not calibrating the z-axis but only from zeroing the z axis too close to the material. Also in your design did you specify the actual depth and the length of tool (end mill/ bit) that you are using?
Click the link to add information to this solution:
I bought a Blacktoe 2 x 8 three years ago and have always had a problem with the Zid axis. No matter how tightly I've calibrated the axis it always cuts to deep. Can I put a larger Stepper motor on Z-axis using the same motion electronics that came with the original machine.
I have a lead screw machine I built from the book plans (i know, ancient history) and I'm thinking of converting the X and Y axis to rollerchain. Assuming I can configure my controller appropriately, is there anything I should buy besides chain, drive cog, tension cog and mounting hardware?
You want to make sure that the motors will be able to provide the necessary torque since there will not be mechanical advantage using roller chain. You will need a way to fix the chain to each end. I like to use #4 - 3/4" screws and #4 nuts. You will need a drive sprocket for each axis and a couple idler sprockets on each axis to serve as tensioners and guiding the roller chain.

Additional Information:
OK cool. I have NEMA 24 steppers rated 425 oz-in. Is there some rule of thumb I can use to guess if that's enough? I'm not planning to push against hard stock material.
Click the link to add information to this solution:
I have a lead screw machine I built from the book plans (i know, ancient history) and I'm thinking of converting the X and Y axis to rollerchain. Assuming I can configure my controller appropriately, is there anything I should buy besides chain, drive cog, tension cog and mounting hardware?
Placed an order for the cable set for the Pokeys57cnc interface on 10/20 but it is not showing up in My Account as being ordered. It was charged to my credit card and I have not had any info that it was received by you.
Sure, let me check.

Additional Information:
Your order was shipped out on Tuesday (10/20/2020). I noticed that your email was not stored in the customer record when the order was made. I will send you the tracking number via email now.
Click the link to add information to this solution:
Placed an order for the cable set for the Pokeys57cnc interface on 10/20 but it is not showing up in My Account as being ordered. It was charged to my credit card and I have not had any info that it was received by you.
I buy a four axis kits and i connect all parts respecting the plan. The USB connector is using for électric alimentation of the When I want to activate the engine with the computer keyboard , nothing works. The current 5VDC since green light is on but when I check with a voltmeter each pin , then I see that there is no current. What's happening?
Depending on the board you are currently using, either the Parallel or USB interface board.
The parallel interface needs the USB cable for power(5v) and the parallel cord for communicating from the board to the computer and vise versa.
The USB interface board, will need a keyboard jog header made to fit the 12 pin connector(2 x 6). Making this connector will allow you to be able to wire it to a external panel, where you can use it to jog your machine rather than using the onscreen jogging.

Please contact customerservice@buildyourcnc.com for further assistance.
Click the link to add information to this solution:
I buy a four axis kits and i connect all parts respecting the plan. The USB connector is using for électric alimentation of the When I want to activate the engine with the computer keyboard , nothing works. The current 5VDC since green light is on but when I check with a voltmeter each pin , then I see that there is no current. What's happening?
Hi Patrick right now I have a parallel port cnc machine that I built in 2013 using the hardware and components I purchased from your website. I want to update my system by changing my current parallel port interface board to a Mach3 USB interface board from your website. Is the Mach3 USB interface board all I need to do this or is there other components I need to get. please advise.
The Mach3 USB interface board will require a 24V power supply to enable the use of the input, output terminals, and the spindle VFD 0-10V and output for speed control.
Click the link to add information to this solution:
Hi Patrick right now I have a parallel port cnc machine that I built in 2013 using the hardware and components I purchased from your website. I want to update my system by changing my current parallel port interface board to a Mach3 USB interface board from your website. Is the Mach3 USB interface board all I need to do this or is there other components I need to get. please advise.