[ Log In ]
[ Register ]

Question #: 13698

Question: Do you cut Linear Guide Rail 20mm too 3000mm or at least 1500mm?

Current Solution

The HIWIN spec linear guide rail that we sell has a maximum length of 2000mm. We can cut them at 1500mm, or you can align them end-to-end if you need 3000mm (i.e. one full 2000mm and one 1000mm).
https://www.buildyourcnc.com/item/mechanical-rails-HIWIN-Linear-20mm-Guide-Rail

If you are referring to our round 20mm rail, they come in 1400mm full lengths and we can cut them to length as well.
https://www.buildyourcnc.com/item/mechanical-rails-linear-guide-rails-20mm

Both of the product pages have a cut to order price option.

Respond:

Other Possible Solutions to this Question

  • DO YOU HAVE CAD AVAILABLE FOR THE HIWIN GUIDE BLOCKS SELL AND RAIL?

    We don't have cad models of the HIWIN blocks, but you can find the models on McMaster.com. They have can drawings and models for most of these types of parts.

    Click the link to add information to this solution:
    DO YOU HAVE CAD AVAILABLE FOR THE HIWIN GUIDE BLOCKS SELL AND RAIL?

  • DO YOU HAVE SPECIAL DEALS FOR HACKERSPACES OR NON-PROFIT ORGANIZATIONS?

    We just don't make enough on our machines to justify any discounts. We try to offer everyone the same low price.

    If I can help in another way, please let me know.

    Click the link to add information to this solution:
    DO YOU HAVE SPECIAL DEALS FOR HACKERSPACES OR NON-PROFIT ORGANIZATIONS?

  • DO YOU ACCEPT CREDIT CARDS MASTERCARD OR VISA

    Yes, we accept standard credit cards on our shopping cart. All you need to do is enter the credit card information in the payment area.

    Click the link to add information to this solution:
    DO YOU ACCEPT CREDIT CARDS MASTERCARD OR VISA

  • DO NEED TO SQUARE UP THE MACHINE AND IF SO YOU HAVE INSTRUCTIONS OR VIDEO FOR THIS?

    The eyebolts are used in the squaring of the machine. I would use a standard carpenters square and first run the end mill along the edge of the square to first make it parallel with the long axis. Then run the end mill along the other edge with the short axis and adjust the eye bolts and chain according to the angle that the machine is out of square.

    Additional Information:

    Click the link to add information to this solution:
    DO NEED TO SQUARE UP THE MACHINE AND IF SO YOU HAVE INSTRUCTIONS OR VIDEO FOR THIS?

  • DO YOU HAVE BLACKTOE MACHINES WITH TABLES READY TO GO OR HOW LONG DOES IT TAKE MAKE ONE?

    Yes, we have the optional table for the blackToe, but we need to fabricate it, which only takes one day. We generally reserve one week for the total fabrication and packing of all parts.

    Click the link to add information to this solution:
    DO YOU HAVE BLACKTOE MACHINES WITH TABLES READY TO GO OR HOW LONG DOES IT TAKE MAKE ONE?

  • DO YOU TYPICALLY PUT SPOILER BOARD ON TOP, IF SO HOW ATTACH IT?

    Yes, this is a must. You can attach the spoil board on the machine with screws, or you can setup a clamping system. We just screw it down.

    Click the link to add information to this solution:
    DO YOU TYPICALLY PUT SPOILER BOARD ON TOP, IF SO HOW ATTACH IT?

  • DO YOU GUYS SELL THE POTENTIOMETER FOR YOUR LASER SYSTEM BY ITSELF

    Yes, it is found in laser components section

    Click the link to add information to this solution:
    DO YOU GUYS SELL THE POTENTIOMETER FOR YOUR LASER SYSTEM BY ITSELF

  • DO YOU SUPPLY THE MALE PORTION OF MOTOR CONTROL CABLES WITH REDLEAF?

    Yes and properly soldered.

    Additional Information:
    20

    Click the link to add information to this solution:
    DO YOU SUPPLY THE MALE PORTION OF MOTOR CONTROL CABLES WITH REDLEAF?

  • DO YOU GIVE AWAY THE PLANS FOR REDLEAF/REDSPROUT BOX?

    Thanks for the kind words. The kit is available for those that want the parts to assemble the case which comes with the computer parts. If you don't need the computer parts, let me know and I will offer the bare bones without the computer system.

    Previous Solution:
    I already have a DIY CNC machine with all my electronics but I have two cases the size of a mid tower PC and was looking to shrink the weight and footprint of all of them. I understand if you don't have plans available, I just really loved the design and compactness of your case.

    Previous Solution:
    The redLeaf and redSprout boxes are meant to provide enclosure to the systems that we assemble in-house for customers that prefer a complete plug and play system. We provide the kit of parts for the enclosure from overwhelming customer request. There are no plans available for the enclosure and the complexity of the parts needed to be fabricated is quite high where the task of cutting out all of the intricate parts by hand would be a larger investment in time and materials than the cost to purchase the kit.

    Additional Information:
    Just curious at what you would sell the box itself empty or the dimension files for the box for?

    Additional Information:



    Additional Information:

    Click the link to add information to this solution:
    DO YOU GIVE AWAY THE PLANS FOR REDLEAF/REDSPROUT BOX?

  • DO YOU GIVE AWAY THE PLANS FOR REDLEAF/REDSPROUT BOX?

    Thanks for the kind words. The kit is available for those that want the parts to assemble the case which comes with the computer parts. If you don't need the computer parts, let me know and I will offer the bare bones without the computer system.

    Previous Solution:
    I already have a DIY CNC machine with all my electronics but I have two cases the size of a mid tower PC and was looking to shrink the weight and footprint of all of them. I understand if you don't have plans available, I just really loved the design and compactness of your case.

    Previous Solution:
    The redLeaf and redSprout boxes are meant to provide enclosure to the systems that we assemble in-house for customers that prefer a complete plug and play system. We provide the kit of parts for the enclosure from overwhelming customer request. There are no plans available for the enclosure and the complexity of the parts needed to be fabricated is quite high where the task of cutting out all of the intricate parts by hand would be a larger investment in time and materials than the cost to purchase the kit.

    Additional Information:
    Just curious at what you would sell the box itself empty or the dimension files for the box for?

    Additional Information:



    Additional Information:

    Click the link to add information to this solution:
    DO YOU GIVE AWAY THE PLANS FOR REDLEAF/REDSPROUT BOX?

  • HOW DO YOU HOOK UP THE SPINDLE TO INVERTER?

    U - Pin1
    V - Pin2
    W - Pin3
    Pin4 Dead

    Additional Information:
    My home made cnc is a big problem with my NC connection. When in start my spindle it will be gone wrong. It will be limith switch problem anytime. Need help thanks.

    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:

    Click the link to add information to this solution:
    HOW DO YOU HOOK UP THE SPINDLE TO INVERTER?

  • HOW DO YOU SETUP THE SPINDLE INVERTER VFD?

    Change PD001 Source of Run Commands to '1'
    Change PD005 Max operating frequency to 400hz
    Change PD004 base frequency to 400hz
    Change PD003 Main frequency to 400hz
    Change PD006 Intermediate frequency to 2.5
    Change PD008 max voltage to 220v
    Change PD009 Intermediate voltage to 15v
    Change PD010 Min voltage to 8
    Change PD011 frequency lower limit to >100hz (120hz to start)
    Change PD142 7 Amps
    Change PD143 2
    Change PD144 3000

    Note: PD001 had to be changed back to 0 to allow for keypad control.
    Note2: I had to reverse U and V to get the spindle to go forward in FWD. (reverse any two wires, u&v or w&v for example)

    Additional Information:

    Click the link to add information to this solution:
    HOW DO YOU SETUP THE SPINDLE INVERTER VFD?

  • I HAVE NEMA 34 MOTORS BUT NEED THE ELECTRICAL COMPONENTS DO YOU A KIT WITHOUT INCLUDED?

    If you are looking for the drivers to pair with NEMA 34 stepper motors, you can find the 6.0 amp drivers here:
    https://www.buildyourcnc.com/item/electronicsAndMotors-stepper-driver-6!0a

    The other electronics to send the signals to the 6.0 amp drivers (the control board that operates with the control software) is subject to personal preference, but here they are listed:

    Our breakout board (works with Mach3 and LinuxCNC and requires a parallel port on your computer):
    https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

    The PoKeys57CNC (works with Mach3 and Mach4):
    https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

    Generic USB breakout board (works with Mach3):
    https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

    Additional Information:
    Do I need a driver for every motor or can I use one driver for all four motors

    Additional Information:
    Each motor needs its own driver.

    Click the link to add information to this solution:
    I HAVE NEMA 34 MOTORS BUT NEED THE ELECTRICAL COMPONENTS DO YOU A KIT WITHOUT INCLUDED?

  • HOW DO YOU HOOK UP THE VFD TO SPINDLE?

    U - Pin1
    V - Pin2
    W - Pin3
    Pin4 Dead

    Additional Information:
    My home made cnc is a big problem with my NC connection. When in start my spindle it will be gone wrong. It will be limith switch problem anytime. Need help thanks.

    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:



    Additional Information:

    Click the link to add information to this solution:
    HOW DO YOU HOOK UP THE VFD TO SPINDLE?

  • HOW DO YOU CONNECT THE INVERTER TO AC?

    Input to VFD:
    240V Active - R
    240V Neutral - S
    Ground - E

    Additional Information:

    Click the link to add information to this solution:
    HOW DO YOU CONNECT THE INVERTER TO AC?

  • HOW DO YOU SETUP THE SPINDLE INVERTER?

    Change PD001 Source of Run Commands to '1'
    Change PD005 Max operating frequency to 400hz
    Change PD004 base frequency to 400hz
    Change PD003 Main frequency to 400hz
    Change PD006 Intermediate frequency to 2.5
    Change PD008 max voltage to 220v
    Change PD009 Intermediate voltage to 15v
    Change PD010 Min voltage to 8
    Change PD011 frequency lower limit to >100hz (120hz to start)
    Change PD142 7 Amps
    Change PD143 2
    Change PD144 3000

    Note: PD001 had to be changed back to 0 to allow for keypad control.
    Note2: I had to reverse U and V to get the spindle to go forward in FWD. (reverse any two wires, u&v or w&v for example)

    Additional Information:

    Click the link to add information to this solution:
    HOW DO YOU SETUP THE SPINDLE INVERTER?

  • IS THE CNC MACHINE HARDWARE & PLANS COMBO SHOWN AT LINK YOU LISTED SAME DESCRIBED IN BOOK?

    Yes, the CNC machine hardware and plans combo is the same machine as in the book. The machine that we provide the plans for, can be found on the website, here http://buildyourcnc.com/Item/cnc-machine-scratchbuild

    Additional Information:



    Additional Information:

    Click the link to add information to this solution:
    IS THE CNC MACHINE HARDWARE & PLANS COMBO SHOWN AT LINK YOU LISTED SAME DESCRIBED IN BOOK?

  • WAS WONDERING IF YOU COULD TELL ME WHETHER OR NOT SHIP ANY OF YOUR KIT PRODUCTS TO THE UK?

    You can determine if the area is serviceable by:
    - selecting the items you want to purchase on the website
    - go to the cart (shopping cart top left of any webpage)
    - log in, or register
    - Enter the address and click on calculate shipping.

    The webpage will return the direct rates and whether your area is serviced or not. Feel free to enter any address as long as you are able to receive the package from that address.

    Click the link to add information to this solution:
    WAS WONDERING IF YOU COULD TELL ME WHETHER OR NOT SHIP ANY OF YOUR KIT PRODUCTS TO THE UK?

  • I HAVE YOUR MACH3 USB BOB, DO YOU GUYS SELL A TORCH CONTROL RELAY CAN WIRE UP TO TURN MY PLASMA ON AND OFF HOW WOULD WIFE THAT TOO THIS BOB?

    We do have a relay board that words like a standard relay.

    Here is the URL of the relay board that we offer:

    https://www.buildyourcnc.com/item/electronicsAndMotors-breakout-Relays-relay-board-250V-12A-5V

    Click the link to add information to this solution:
    I HAVE YOUR MACH3 USB BOB, DO YOU GUYS SELL A TORCH CONTROL RELAY CAN WIRE UP TO TURN MY PLASMA ON AND OFF HOW WOULD WIFE THAT TOO THIS BOB?

Get Help with:
This Product
Orders
Tech Support
Sales
This Product
Order Query
Tech Support
Sales
Not logged in. Log In Register
Track Order(s)
View Order(s)
I Want to Schecule a One-On-One Paid Tech Support Session
Book an Appointment Pertaining to a BuildYourCNC Product (Free)
Ask a Quesion Below (Free):
Book an Appointment Pertaining Other Equipment ($60/half hour)
Book an Immedite Appointment Pertaining Other Equipment ($120/half hour)
Ask a Quesion Below (Free):
Waiting for response... I may not answer immediately, but I was notified on my cellular phone so my response is forthcoming. If I don't respond immediately, you can always go to the [My Account] page to see all of our chats at any time.