If you would like to use a spindle rather than a router on your existing CNC, we will send you another set of components that will allow the spindle to be mounted properly which includes the z-axis rails, rail support, spindle mounts and the dust shoe components. You can find this item to purchase here: https://www.buildyourcnc.com/category/z-axis

Click the link to add information to this solution:
I HAVE BLACKTOE 4.1 WITH PORTER CABLE 890 ROUTER.TO CONVERT TO SPINDLE(2.2KW) CAN JUST CHANGE THE MOUNT?

If your computer does not have a parallel port, all you will need is a low cost PCI parallel adapter card (these can be found on amazon for $15-$20). If you plan on using a laptop (not recommended) you can try to find a PCMCIA parallel adapter, but many people have frequent issues with this setup. A more expensive solution would be to purchase a USB smooth stepper board. Unfortunately, we do not supply any of these adapters and cannot attest to their reliability.

Additional Information:
ur gay

Additional Information:

Click the link to add information to this solution:
MY COMPUTER DOES NOT HAVE A PARALLEL PORT. HOW DO I INTERFACE WITH THE BREAKOUT BOARD?

If your computer does not have a parallel port, all you will need is a low cost PCI parallel adapter card (these can be found on amazon for $15-$20). If you plan on using a laptop (not recommended) you can try to find a PCMCIA parallel adapter, but many people have frequent issues with this setup. A more expensive solution would be to purchase a USB smooth stepper board. Unfortunately, we do not supply any of these adapters and cannot attest to their reliability.

Additional Information:
ur gay

Additional Information:

Click the link to add information to this solution:
MY COMPUTER DOES NOT HAVE A PARALLEL PORT. HOW DO I INTERFACE WITH THE MACHINE?

The leadscrew length for the greenBull long Z-axis is 47 inches.

Additional Information:

Click the link to add information to this solution:
BUILDING ONE OF YOUR GREENBULL 6X LONG AND 2.2 KILOWATT SPINDLE DOES NOT FIT. SEEMS LEAD SCREW YOU SENT WITH KIT IS SHORT 42" LOOKS LIKE IT NEEDS TO BE 5 OR 6 INCH LONGER. THIS CORRECT? WHAT THE NEEDED LENGTH FOR UNIT?

Yes, we have the optional table for the blackToe, but we need to fabricate it, which only takes one day. We generally reserve one week for the total fabrication and packing of all parts.

Click the link to add information to this solution:
DO YOU HAVE BLACKTOES WITH TABLES?

Unfortunately I am not able to give an estimate of shipping time. This is because there are multiple shipping options, Some of them cost more than others, but ensure the package arrives in a certain number of days. Others do not give a number of days, and many factors could change the length of shipping time, such as weather, or busy season. It would be best to choose an option you are comfortable with the price of, and then Google search the typical times it takes for that option to get to you, or call the shipping company and request that estimated time from them.

Additional Information:

Click the link to add information to this solution:
HOW LONG DOES IT TAKE TO SHIP

It is not recommended that standard routers do full depth passes. This is better done with a spindle. For best results with routers, we recommend a depth that equals the cutting diameter of the end mill. The IPM will relate to the chip load of the end mill (look up the formula online and add it here). The IPM will also depend on the end mill diameter, the larger the diameter, the faster the feedrate. A 1/2" end mill can cut about 300-500 ipm where a 1/4" end mill will be able to cut at 80-120 IPM, at a depth equaling the cutter diameter using a router. With a spindle, the same feedrates can be applied, but with more depth per pass. For instance, an MDF full depth cut at 3/4" can be cut at the 100 IPM using a 1/4" cutter.
Here is a basic setup we have for our blackFoot (default setting):
X-Axis
SPI: 914.29
Acc: 400.02
Vel: 5
Y-Axis
SPI: 1422.22
Acc: 400.02
Vel: 5
Z-Axis
SPI: 1600
Acc: 400.02
Vel: 79.98

Click the link to add information to this solution:
I have a BlackFoot with a 3.25hp Porter Cable router. What is a safe starting IPM to optimize feed rate? How fast do you guys run full depth passes through MDO or MDF?

Yes, we accept standard credit cards on our shopping cart. All you need to do is enter the credit card information in the payment area.

Click the link to add information to this solution:
DO NOT HAVE PAYPAL ACCOUNT, WITH NO DESIRE TO OBTAIN ONE.

The eyebolts are used in the squaring of the machine. I would use a standard carpenters square and first run the end mill along the edge of the square to first make it parallel with the long axis. Then run the end mill along the other edge with the short axis and adjust the eye bolts and chain according to the angle that the machine is out of square.

Additional Information:

Click the link to add information to this solution:
DO NEED TO SQUARE UP THE MACHINE AND IF SO YOU HAVE INSTRUCTIONS OR VIDEO FOR THIS?

The length of time it will take to build a CNC machine kit is not an easy answer. There may be a wide array of circumstances that limit a persons abilities to build the cnc machine kit in an efficient timeframe; however, if you have moderate dexterity and moderately mechanically inclined, you should have no problem building one of our machines within one weekend if the project has very little downtime.

Additional Information:

Click the link to add information to this solution:
HOW LONG WOULD IT TAKE FOR MY TO BUILD A MACHINE?

The motor cables for the blackToe are as follows:

Total 30 feet

X - 9
Y - 10
Z - 11

Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
HOW LONG SHOULD THE MOTOR CABLES BE FOR BLACKTOE

Yes, it is ok if the thickness is plus or minus +/- about 2mm.

Additional Information:



Additional Information:

Click the link to add information to this solution:
is IT OK TO USE THICKER PLYWOOD (MATERIAL) to BUILD THE CNC MACHINE, BLACKFOOT, BLACKTOE?

Yes, it is ok if the thickness is plus or minus +/- about 2mm.

Additional Information:



Additional Information:

Click the link to add information to this solution:
IT OK TO USE THICKER PLYWOOD (MATERIAL) BUILD THE CNC MACHINE, BLACKFOOT, BLACKTOE?

Yes, that is highly recommended for all the reasons you can imagine. Say you were doing engraving, not surfacing the spoilboard will either exhibit some areas that have no engraving at all, or areas that have engraving that is too deep. If you are cutting completely through the material, then one end may be cut all the way through but the other end will not have a complete cut, or produce onion skinning on the bottom of the workpiece.

Click the link to add information to this solution:
DO NEED TO GET THE BIG PLANING BIT OR SURFACING AND GO OVER SPOIL BOARD MAKE SURE THAT IT IS PERFECTLY LEVEL IN RELATION ROUTER?

The motor that is attached to the 4th axis is wired as follows:

The motor should have red, green yellow and blue wires coming form the motor. The red and green are paired as one coil and the yellow and blue is paired as the other coil. You can wire the motor to a 3.0 amp driver with red to A+, green to A-, Yellow to B+ and Blue to B-

Click the link to add information to this solution:
HOW DO I WIRE THE 4TH AXIS THAT YOU SELL. I HAVE MACH3 SOFTWARE. NO INSTRUCTIONS ON YOUR SITE

Check step 9 on this page: http://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

Click the link to add information to this solution:
IF YOU HAVE CIRCUIT (OR PICTURE) OF HOW THIS RELAY IS CONNECTED TO THE ROUTER

We do have a relay board that words like a standard relay.

Here is the URL of the relay board that we offer:

https://www.buildyourcnc.com/item/electronicsAndMotors-breakout-Relays-relay-board-250V-12A-5V

Click the link to add information to this solution:
I HAVE YOUR MACH3 USB BOB, DO YOU GUYS SELL A TORCH CONTROL RELAY CAN WIRE UP TO TURN MY PLASMA ON AND OFF HOW WOULD WIFE THAT TOO THIS BOB?

These machines are inherently dangerous. Before the machine moves, the machine should be clear of any person by a dimension of at the distance of a persons reach plus a few more feet. This is the policies we institute in our shop and what is recommend to all of our customers. Treat these machines as you would treat any major power tool in the shop.

With that said, you can certainly add some protective parts, but still keep folks away even with those installed. I would use the gantry side to do all of the mounting of the protective parts. Consider using sheet metal that you can bend and make a simple installation right on the gantry side.

Additional Information:



Additional Information:

Click the link to add information to this solution:
HOW DO ADDRESS THE DANGER OF THESE CNC MACHINES

The blackTooth Laser cutter and Engraver can be built in a weekend. Take a look at the build instructions and try to determine if you feel you have sufficient capability to put together the laser system.

Click the link to add information to this solution:
HOW COMPLEX IS YOUR KIT TO ASSEMBLE, AND MOST IMPORTANTLY - HARD IT SETUP CONTROL THE LASER WITH MACH3?