Yes, we have the optional table for the blackToe, but we need to fabricate it, which only takes one day. We generally reserve one week for the total fabrication and packing of all parts.

Click the link to add information to this solution:
DO YOU HAVE BLACKTOE MACHINES WITH TABLES READY TO GO OR HOW LONG DOES IT TAKE MAKE ONE?

The length of time it will take to build a CNC machine kit is not an easy answer. There may be a wide array of circumstances that limit a persons abilities to build the cnc machine kit in an efficient timeframe; however, if you have moderate dexterity and moderately mechanically inclined, you should have no problem building one of our machines within one weekend if the project has very little downtime.

Additional Information:

Click the link to add information to this solution:
HOW LONG WOULD IT TAKE FOR MY TO BUILD A MACHINE?

The average lifespan of a tube is 1000-1500 hours IF ran at a max of 16mA for most of it's life. It's life will go down if you run constantly at it's max rating.

CO2 laser tubes also have a shelf life. So make sure to only buy a replacement tube close to when you plan to install it, keeping it on a shelf for the future will only compromise it's life span.

To measure your amperage going through your system. You go from the negative line of the tube and run it THROUGH your multimeter/ammeter and back out to the laser PSU. This will give you your amp usage. It will not hurt your multimeter either. Just be sure your connections are very snug since 20,000V is liable to arc very easily if a connection comes loose.

Additional Information:
what is life span of CO2 generator in videojet laser coding machineVJ3320

Click the link to add information to this solution:
HOW LONG DOES THE TUBE LAST?

The length of time it will take to build a CNC machine kit is not an easy answer. There may be a wide array of circumstances that limit a persons abilities to build the cnc machine kit in an efficient timeframe; however, if you have moderate dexterity and moderately mechanically inclined, you should have no problem building one of our machines within one weekend if the project has very little downtime.

Additional Information:

Click the link to add information to this solution:
HOW LONG FOR ME TO BUILD IT?

Protection from influenza vaccine is thought to persist for a year or less because of waning antibody and because of changes in the circulating influenza virus from year to year.

Click the link to add information to this solution:
HOW LONG DOES IMMUNITY FROM INFLUENZA (FLU) VACCINE LAST?

To loosen and tighten the collet nut for the 2.2kW spindle, I use a 22mm wrench (spanner) for the shaft and a 30mm wrench for the nut.

Click the link to add information to this solution:
WHAT SIZE WRENCHES DOES THIS SPINDLE TAKE TO TIGHTEN?

The triangle has three (3) sides. The triangle is a polygon that contains three sides and three inner angles and three vertices.

Additional Information:
But if a triangle have a front and back side wouldn't the triangle have 5 sides

Additional Information:
Interesting slant (pun). A triangle would have 5 sides if the triangle had a thickness and became an object. A triangle drawn on paper with three lines would still only have three sides. A triangle is a primitive form of geometry (polygon) that can only have three sides in its simplest form. If you add complexity to the triangle with a thickness and count two more sides, then it really isn't the simplest form of the triangle anymore and it becomes another geometrical 3D primitive like a triangular prism.

Additional Information:
A triangle has multiply answers for number of sides but is made up of 3 lines.. this is because when connecting the 3rd line to form the shape you create an "inside". so you could say a triangle has 2 sides, an "outside" and "inside" or you could say 4 sides, an "inside" and 3 "outside facings" or 6 sides 3 "outside facings" and 3 "inside facings". none of these answers are incorrect technically. the important thing is that a triangle is made up of 3 inner angles adding upto 180 degree's.

Additional Information:
A triangle has 6 sides, there are 3 straight edges in AND out side of a triangle.

Additional Information:
I am fairly sure that a triangle has 12 sides (3 insides and 3 outsides on each side).

Additional Information:


Additional Information:


Additional Information:


Additional Information:
4

Additional Information:
4

Additional Information:
4

Additional Information:
How many sides do a triangle have

Additional Information:
How many sides do a triangle have

Additional Information:
How many sides do a triangle have

Additional Information:


Additional Information:


Additional Information:


Additional Information:


Additional Information:


Additional Information:
4


Additional Information:


Additional Information:


Additional Information:

Click the link to add information to this solution:
HOW MANY SIDES DOES A TRIANGLE HAVE?

The violin has four strings.

Additional Information:
3

Additional Information:

Click the link to add information to this solution:
HOW MANY STRINGS DOES A VIOLIN HAVE?

The blackTooth Laser cutter and Engraver can be built in a weekend. Take a look at the build instructions and try to determine if you feel you have sufficient capability to put together the laser system.

Click the link to add information to this solution:
HOW DIFFICULT IS IT TO BUILD THE BLACKTOOTH

The motor cables for the blackToe are as follows:

Total 30 feet

X - 9
Y - 10
Z - 11

Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
HOW LONG SHOULD THE MOTOR CABLES BE FOR BLACKTOE

Yes we can ship to either country. Sometimes we may have to use a particular carrier, which could result in a higher shipping cost.

Click the link to add information to this solution:
CAN WE SHIP TO MALAYSIA OR IRAQ?

You can determine if the country is serviceable by:
- selecting the items you want to purchase on the website
- go to the cart (shopping cart top left of any webpage)
- log in, or register
- Enter the address and click on calculate shipping.

The webpage will return the direct rates and whether your area is serviced or not. Feel free to enter any address as long as you are able to receive the package from that address.

Click the link to add information to this solution:
CAN YOU SHIP ITEMS TO MY COUNTRY?

The blackTooth Laser cutter and Engraver can be built in a weekend. Take a look at the build instructions and try to determine if you feel you have sufficient capability to put together the laser system.

Click the link to add information to this solution:
HOW DIFFICULT IS IT TO BUILD THE BLACKTOOTH LASER CUTTER?

Input to VFD:
240V Active - R
240V Neutral - S
Ground - E

Additional Information:

Click the link to add information to this solution:
HOW TO CONNECT THE INVERTER WALL?

U - Pin1
V - Pin2
W - Pin3
Pin4 Dead

Additional Information:
My home made cnc is a big problem with my NC connection. When in start my spindle it will be gone wrong. It will be limith switch problem anytime. Need help thanks.

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
HOW TO CONNECT THE SPINDLE INVERTER?

U - Pin1
V - Pin2
W - Pin3
Pin4 Dead

Additional Information:
My home made cnc is a big problem with my NC connection. When in start my spindle it will be gone wrong. It will be limith switch problem anytime. Need help thanks.

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
HOW DO YOU HOOK UP THE VFD TO SPINDLE?

Input to VFD:
240V Active - R
240V Neutral - S
Ground - E

Additional Information:

Click the link to add information to this solution:
HOW DO YOU CONNECT THE INVERTER TO AC?

Mounting the extruder to the whiteAnt can be done a couple of ways. One is to take the 4 mounting holes located at the lower portion of the z-axis rail support and use long screws protruding out. Take a thinner material and drill the four holes matching the locations of the 4 screws and screw on nuts to hold it in place. The other option would be to use the metal bracket and fasten to the edge of the rail support.

Click the link to add information to this solution:
HOW CAN MOUNT THE EXTRUDER TO WHITEANT

Cooling is not as tricky as you might think. There is 3 ways to approach this, only 2 really matter for a low scale 40w setup. First one is the cheapest and easiest. The higher the temp of water the worse your performance will be, from what I understand anything in the 30C range is about the most tolerable it gets. Lower is better. But not frozen...from what I've been told a very experienced cutter, he found 8C was the highest power he achieved.

1. Use a 5 Gallon resovoir system which gives you a fairly large space of water to heat up before you need to tend to it. Add about a cup of anti-freeze to the mix of DISTILLED water. You don't want ANY minerals in the water that might build up in your system. The anti-freeze works to keep algae and other ickies from growing in your water.

2. Use a smaller resovoir system (or even closed loop) and install 1 or more radiators found in CPU cooling systems with 120mm fans attached. This will continously cool your water system to ambient room temperatures, but with a tiny resovoir it will be difficult to add things like ice-packs to drop the temps if the ambient is quite hot.

3. Using an industrial coolant system. Overkill and unless your cutting A LOT, this is a very expensive option to take. You can also explore the idea of Peltier cooling but it is extremely expensive electricity/BTU wise compared to an industrial cooler.

Click the link to add information to this solution:
HOW TO COOL THE BLACKTOOTH 40W LASER TUBE