Generally, you’ll need to check what control software will need to be used with the CNC router. Our machines use industry standard electronics and control software that is nonproprietary so you can use just about any software out there with our machines.

Specifically, what software are you planning on using?

Additional Information:
dear Sir,
I'm searching for the best one,I think that I have to learn more about that in order to be able to make the right decision.

Additional Information:
If you are using a computer running Microsoft Windows, then I would recommend using Mach3 or Mach4. If you prefer Linux, then LinuxCNC is the best control software in my opinion.

Click the link to add information to this solution:
I am using Windows 10 and my Shopbot PRT 4g uses Shopbot's proprietary software https://www.shopbottools.com/support/control-software. How can I determine if the 4th axis you offer will be compatible with my machine?

if you purchased the USB interface, you will need planet-cnc software rather than Mach3, and you will need a usb cable to connect the usb interface to the computer.

The blackToe 2x4 CNC Machine Kit with optional table will need wire to connect the electronics. Don't forget to get some end mills to use for cutting the intended material.


Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
If I purchase the [blackToe 2x4 v4.1 CNC Machine Kit - USB Electronics - Table Included] all I would need for this CNC to be fully operational is a laptop with mach 3 software and a router. Is this correct?

Currently our USB breakout board is only compatible with Planet-CNC software as it has to be registered with Planet-CNC.

Click the link to add information to this solution:
Hi, I have watched your vids on YouTube and I am interested in purchasing one of your USB Break-Out Boards. I currently own and use FlashCut CNC software, which is USB based, on all of my machines. I'm wondering if you could tell if the Flashcut software will talk with the USB Break-Out Board? Thank You

The plug and play system does have enough memory for additional software. The redLeaf comes standard with a 1TB hard drive.

Click the link to add information to this solution:
DOES THE PLUG AND PLAY ELECTRONICS COMPUTER FOR 3 AXIS CNC MACHINE HAVE ENOUGH MEMORY RAM ADDITIONAL SOFTWARE (BOBCAD-CAM, BOBART, MACH3) TO BE ADDED FUNCTION WELL?

You will need to build the table unit for your machine. There are instructions on how to do this at the bottom of the product page here, https://www.buildyourcnc.com/Item/cnc-machine-blackFoot-v4
There is no estimate on how much this will cost though, since there are too many variables involved to do this.

- PC with parallel port and USB port
- 20awg stranded wires for the motors - http://www.buildyourcnc.com/electronicscombo.aspx
- 18awg stranded wires for power supply to drivers
- 24awg stranded wires for breakout board to drivers
(location and spacing of components varies from one person to another, so we do not provide cables/wires)
- General purpose extension cord (cut the female end off) to provide power to power supply
- USB cable to power breakout board
- Parallel cable to communicate to breakout board
- Router
- (optional - instead of router) Spindle with power inverter http://www.buildyourcnc.com/SpindlesAndAccessories.aspx
- (if purchasing spindle with inverter) General purpose extension cord (240v) (cut the female end off) to provide power to power inverter
- End Mill(s) http://www.buildyourcnc.com/ProductsEndMills.aspx
- CAD, and/or CAD-CAM software (to produce geometry, machine operations, and g-code) http://www.buildyourcnc.com/CNCsoftware.aspx
- CNC control software (to read g-code and control machine) http://www.buildyourcnc.com/CNCsoftware.aspx

This answer is applicable to most of our machines with the exception of the greenLean and the blueChick since those machines are equipped with a table structure.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
If I purchase a greenBull 6X Long Z CNC Machine Kit and Mach3, what else would be required to assemble the working machine? I have CAD software.

Planet-CNC is the control software. If you decide to use the USB controller, you will need to use the planet-CNC software as the control software. You will be able to use any of the CAM software applications with the planet-CNC control software.

Click the link to add information to this solution:
Would I be able to use the Mach3 CNC Control Software or any of the CNC CAM Software(BOBCAD/CAM,CAMBAM) if I choose to use the Planet-CNC USB Interface Board?

You will need to build the table unit for your machine. There are instructions on how to do this at the bottom of the product page here, https://www.buildyourcnc.com/Item/cnc-machine-blackFoot-v4
There is no estimate on how much this will cost though, since there are too many variables involved to do this.

- PC with parallel port and USB port
- 20awg stranded wires for the motors - http://www.buildyourcnc.com/electronicscombo.aspx
- 18awg stranded wires for power supply to drivers
- 24awg stranded wires for breakout board to drivers
(location and spacing of components varies from one person to another, so we do not provide cables/wires)
- General purpose extension cord (cut the female end off) to provide power to power supply
- USB cable to power breakout board
- Parallel cable to communicate to breakout board
- Router
- (optional - instead of router) Spindle with power inverter http://www.buildyourcnc.com/SpindlesAndAccessories.aspx
- (if purchasing spindle with inverter) General purpose extension cord (240v) (cut the female end off) to provide power to power inverter
- End Mill(s) http://www.buildyourcnc.com/ProductsEndMills.aspx
- CAD, and/or CAD-CAM software (to produce geometry, machine operations, and g-code) http://www.buildyourcnc.com/CNCsoftware.aspx
- CNC control software (to read g-code and control machine) http://www.buildyourcnc.com/CNCsoftware.aspx

This answer is applicable to most of our machines with the exception of the greenLean and the blueChick since those machines are equipped with a table structure.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
IF I PURCHASE A GREENBULL 6X LONG Z CNC MACHINE KIT AND MACH3, WHAT ELSE WOULD BE REQUIRED TO ASSEMBLE THE WORKING MACHINE? HAVE CAD SOFTWARE.

The electronics packages come with standard stepping motor drivers, stepping motors, power supply (36v and 8.8amps), and a breakout board (USB or parallel, depending on the option you select). The USB will not work with linuxcnc, but the parallel breakout board works fine with linuxcnc. All of our drivers work well with the linuxcnc software. We use this software with some of our machines and we also sell the CNC electronics / computer system (redLeaf and redSprout) with linuxcnc installed and tested (if the customer selects linux over windows or requests a dual boot system).

Click the link to add information to this solution:
May i have more detailed Information aboute the 4 Axis Electronics Combo? We're using EMC2 and i wanna check compatibility first before I'll buy some. https://www.buildyourcnc.com/Item/electronicsAndMotors-4axis-425-elcombo

it is possible to install 2 motors on a single axis but you will require another driver and motor, but wire it directly to the same pins on your breakout board. Also the orientation of your motor since it is opposite side of the original so getting it to move accordingly to the original motor it will need to be orientated correctly. The slight shift could be the cause of the rod not being completely flat where the set screws are suppose to tighten the sprocket to the rod, so sanding it to a flatter surface might fix the shift in directions.
Currently do not have a kit or schematic available.

Click the link to add information to this solution:
Hello, I have a BlackToe 2 x 4 machine. I was wondering if it could be beneficial, or even possible to install two motors on the x-axis (one one each chain drive sprocket). I am noticing a slight shift in the gantry with each reversal of direction. If so, do you have a kit or schematic for this? Thanks

Sure, the USB interface has a place for 4 axes of limit switches.

Each axis can have two limit switches: one for the ++ (positive) end and one for the -- (negative) end. The positive end would be the limit switch at the end of the machine that, say the machine has a 4'x8' area, reaches a bit after the 8 foot mark. The negative end would be the limit switch behind the 0 foot location behind the origin. If the origin is in the middle, the negative would be at a little more than the -4 foot end and the positive would be at a bit more than the +4 foot end. Note that you can have more than one switch on each pin where the NC is connected in serial fashion and the NO is connected in parallel fashion (this can be seen on the diagram in the multiple limits switch section). The software configurations for the limits switches are under File -> Settings -> Limit.

A typical limit switch has three connections on it. These connections consist of COM (common), NC (normally closed) and NO (normally open). The COM would generally go to GND and the NC or the NO would go to the pin. If the NC is used, then the the switch is constantly connected until the switch is pushed (engaged) then the connection from the pin to gnd is broken (open). Use the settings in software to set whether in NC or NO configuration.

Let me know if this information was helpful (or not) by adding information to this question. Thanks.

User response:
Thank you very much for this helpful information. I'm still a little fuzzy on how the 6 limit switches physically connect to each other and to the USB breakout board. You've stated one switch (home) goes to positive and another switch (limit) goes to negative. Are all the GND prongs from all 6 switches connected to each other and going to GND on the breakout board, or no? And the NC prongs, how exactly are they connected to each other? And to the board? There has to be a diagram somewhere shows this visually, no? I don't know how to wire the switches in series or in parallel. I have already physically installed all the switches on the machine and ran the wires to where the board is. Now I just need to know where to plug these wires into the board. Also, taking into consideration that I'm using the Planet CNC software, the only settings I have pertaining to limit switches is "Enable/Disable" for each axis, and the actual limit for each axis. Nothing about NC or NO. Is that only in Mach3?
Thank you.

buildyourcnc response:
On the USB interface, the COM on the switch connects to GND and the NC or NO connects to the input pin (i.e. x++, y--, etc.)

Limit switch configuration is rather difficult to understand, especially with series and parallel. You can think of series as a single wire going from GND to the axis letter input terminal (i.e. X++ or X--). If the wire is broken, then the circuit is open (or the switch is engaged in a normally closed scenario). Normally closed is like an actual wire, and when engaged, the switch "opens" (breaks the wire). This is why we recommend in some systems that you can put many switches in series on a single pin. When one of the switches is engaged (breaking the connection) then the entire circuit of switches is broken and the machine stops.

In a parallel scenario, the state of the circuit is always broken until the one of the switches is engaged and the circuit is then closed or connected. The topology looks like a ladder. All the switches connect to both sides of the ladder and the switches are like the runs of the ladder (the horizontal bars that the feet are placed while climbing). Imagine all of the switches broken in this scenario (normally open). It would be like the ladder could be split in two, but if one of the ladder runs (switches) is closed by engaging it, then that run would connect both sides of the ladder and the two sides of the ladder would have a connection.

There is a diagram on the USB page of the various limit switch configurations. If you need more information (visual and/or otherwise), please let us know and we will immediately add that information to benefit everyone.

Click the link to add information to this solution:
I have nearly completed the CNC machine from the book, but I am using it with a USB breakout board, and have no idea how to wire the 6 limit switches to the board. I'm having difficulty following the diagram on the USB breakout board screen. Can someone please help me?

If you purchase the greenLean, you will get everything you need except a router, computer to operate the machine, and software to control the machine. You state that you have a computer. You can use this computer, but you will need to determine if it has a parallel port, or if you are going to need the USB controller option. As for the software, there are too many different options for you to choose from. We would not be able to tell you which to get, and how much it will cost you. This is a matter of preference. I can tell you, however, that you will need 3 types of software to complete a CNC project. You will need CAD software to design your design, CAM software to add tool paths and convert the design to g-code, and then control software to take the g-code and operate the machine.

Additional Information:
20

Click the link to add information to this solution:
I am building a wet plasma table for my shop that is 8'x 16'. I will need hardware and software. Please heko me wuth the list, My phone is 9124273734. I would like to talk with someone if possible. Thanks, Rus

All of our controller will allow two steppers on any of the axes. Multiple stepper motors and drivers on a single axis is more a function of the way the stepper motor drives are connected to the output pins of the controller. To connect two stepper drivers to a single axis, you need to connect the output pins (dir and step) to each of the two stepper motor drivers.

Consider the controller on cost, features and how they are connected to the computer.

Out lowest cost controllers are:

Mach3 USB board - Has good features and uses the USB from the computer as the main connection
https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Parallel Breakout - The computer generates the main signals and this board conditions the signals for the drivers. Although it requires the parallel port from older computer, the board has the most broad compatibility with control software out there including Mach3 and LinuxCNC.
https://buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

Highest cost but most feature rich:

Pokey57CNC - works with both Mach3 and Mach4
https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Click the link to add information to this solution:
I am looking for a controller for a 3 axis dual Y stepper cnc machine. If at all possible I would like a list of the parts that will be needed. I prefer to go with an ethernet setup vs a parallel port.

If you purchase the greenLean, you will get everything you need except a router, computer to operate the machine, and software to control the machine. You state that you have a computer. You can use this computer, but you will need to determine if it has a parallel port, or if you are going to need the USB controller option. As for the software, there are too many different options for you to choose from. We would not be able to tell you which to get, and how much it will cost you. This is a matter of preference. I can tell you, however, that you will need 3 types of software to complete a CNC project. You will need CAD software to design your design, CAM software to add tool paths and convert the design to g-code, and then control software to take the g-code and operate the machine.

Additional Information:
20

Click the link to add information to this solution:
Hello  We would like to buy a greenLean Vertically Oriented CNC Machine we start from scratch and want to make sure that we get all the pieces, we need  hardware and software we have a PC and a Mac

If you purchase the greenLean, you will get everything you need except a router, computer to operate the machine, and software to control the machine. You state that you have a computer. You can use this computer, but you will need to determine if it has a parallel port, or if you are going to need the USB controller option. As for the software, there are too many different options for you to choose from. We would not be able to tell you which to get, and how much it will cost you. This is a matter of preference. I can tell you, however, that you will need 3 types of software to complete a CNC project. You will need CAD software to design your design, CAM software to add tool paths and convert the design to g-code, and then control software to take the g-code and operate the machine.

Additional Information:
20

Click the link to add information to this solution:
Hello  We would like to buy a greenLean Vertically Oriented CNC Machine we start from scratch and want to make sure that we get all the pieces, we need  hardware and software we have a PC and a Mac

Connecting the limit switches on the redLeaf use the input pins on the parallel breakout board. Here is a link to the wiring diagram for that parallel breakout board.

https://buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay#prettyPhoto/2/

The connection is simple. Just create a circuit from ground to the pin. When the pin is engaged, the circuit is closed (using normally open on the switch). Use mach3's autoset to automatically set the pin for the limit or home setting.

Click the link to add information to this solution:
Do you guys have any videos showing how to connect limit switches to a redleaf? If not, could you please make one? I looked at the diagrams on the limit switch page but I don't understand them.

BYCNC Response:
This is correct. You will need to use a method appropriate for the software you are using. Also remember that NC switches are typically wired in series, while NO switches are normally wired in parallel.

User Response:
I am using the cnc planet software for your USB board. Are the limit configurations in this software?

BYCNC Response:
Yes, Planet CNC software is compatible with the use of limit switches. Configuration information will depend on your specific application. You can view Planet CNC's information here: http://www.planet-cnc.com/files/CNCUSBController.pdf

Click the link to add information to this solution:
LIMIT SWITCHES FOR AXIS. THE PRINT SHOWS THAT YOU CAN WIRE LIMITS EITHER N.O. OR N.C. SO IF THIS IS CORRECT I WOULD NEED TO TELL BOARD IN SOFTWARE HOW LOOK AT THESE LIMITS, I'M GOING GET AN INPUT LOOSE DEPEND ON IT.

Yes, if you need a replacement part on your machine please call us at 281-815-7701.

Click the link to add information to this solution:
I have a blacktooth laser engraver. The Y Axis stepper motor needs to be replaced. Can you please provide me with the information I would need to replace this motor.

We would highly recommend using our forums to sell you machine buildyourtools.com.
We currently do not have a page or option to allow our customers to sell our machines, you can also contact us at customerservice@buildyourcnc.com, for further assistance dealing with the machine and in regards to selling it.

Click the link to add information to this solution:
I have a blueChick 13"x24" or 13"x36" Desktop CNC Router Kit v3.0 (Timing Belt) that I've assembled but never was able to get it running. Can BuildYourCNC assist me in selling this machine? Do you have used machine offerings on your site?

We carry several sizes of lead screw and stepper motors on our website, for example here https://buildyourcnc.com/Item/mechanical-leadscrews-lead-screw-!5-5-starts-10-tpi and here https://buildyourcnc.com/ProductSearchResults.aspx. Please call us at 281-815-7701 to discuss the particular lengths you would need and shipping options.

Additional Information:
https://buildyourcnc.com/ProductSearchResults.aspx is not working

Additional Information:



Additional Information:

Click the link to add information to this solution:
I have a project very similar to cnc machine. I need 3 lead screws of 1.8 m with all set (supports, bearings...etc). and 3 NEMA 42 motors that I can connect with. if those are available, I need the information about shipping to Oman or UAE.