The password is: 608

Click the link to add information to this solution:
WHAT IS THE SYSTEM PASSWORD FOR LASER CONTROL UNIT?

Please visit this link https://buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay#prettyPhoto
and follow the steps described on the bottom of the page.

Click the link to add information to this solution:
5 AXIS CONTROLLER ISSUES.

I don't see anything in the datasheet for the relay that indicates an overheat condition. While the relay is engaged, the power consumption is 400 mW and I don't believe this is enough to raise the temperature faster than the heat dissipation from the metal on the leads through convection or radiation outside of the rated temperature working ranges providing that you maintain an ambient temperature range within -40°C to 85°C (with no icing or condensation).

http://www.omron.com/ecb/products/pdf/en-g2rl.pdf

Click the link to add information to this solution:
IS IT OK TO LEAVE THE VACUUM PRESSURE CONTROLLER PLUGGED IN ALL TIME WHEN PUMP SWITCHED OFF?

This video will illustrate how to test for laser power:

Click the link to add information to this solution:
LOSE POWER IN MY LASER TUBE

Cooling is not as tricky as you might think. There is 3 ways to approach this, only 2 really matter for a low scale 40w setup. First one is the cheapest and easiest. The higher the temp of water the worse your performance will be, from what I understand anything in the 30C range is about the most tolerable it gets. Lower is better. But not frozen...from what I've been told a very experienced cutter, he found 8C was the highest power he achieved.

1. Use a 5 Gallon resovoir system which gives you a fairly large space of water to heat up before you need to tend to it. Add about a cup of anti-freeze to the mix of DISTILLED water. You don't want ANY minerals in the water that might build up in your system. The anti-freeze works to keep algae and other ickies from growing in your water.

2. Use a smaller resovoir system (or even closed loop) and install 1 or more radiators found in CPU cooling systems with 120mm fans attached. This will continously cool your water system to ambient room temperatures, but with a tiny resovoir it will be difficult to add things like ice-packs to drop the temps if the ambient is quite hot.

3. Using an industrial coolant system. Overkill and unless your cutting A LOT, this is a very expensive option to take. You can also explore the idea of Peltier cooling but it is extremely expensive electricity/BTU wise compared to an industrial cooler.

Click the link to add information to this solution:
HOW CAN COOL THE LASER TUBE?

The lens is 20mm wide and a 50.6mm focal length (the one included). This lens will stand up to at least 30PSI air assist.

The mirrors are 25mm wide mirrors.

Focal length is the distance from the lens to the material for the laser converge into the best focal point. If a lens is listed as 2". You measure 2" from the lens to the material, this will be the tightest point the laser can go before it starts to re-expand again losing focus.

Click the link to add information to this solution:
WHAT IS LASER AND LENS FOCAL LENGTH?

These tubes are rated for 18mA. The power supply is able to push up to 21mA. This is a very dangerous thing to do. If you are pushing the tube beyond 18mA you will cut it's life by QUITE a bit.

Click the link to add information to this solution:
HOW HARD CAN PUSH MY BLACKTOOTH LASER?

Cooling is not as tricky as you might think. There is 3 ways to approach this, only 2 really matter for a low scale 40w setup. First one is the cheapest and easiest. The higher the temp of water the worse your performance will be, from what I understand anything in the 30C range is about the most tolerable it gets. Lower is better. But not frozen...from what I've been told a very experienced cutter, he found 8C was the highest power he achieved.

1. Use a 5 Gallon resovoir system which gives you a fairly large space of water to heat up before you need to tend to it. Add about a cup of anti-freeze to the mix of DISTILLED water. You don't want ANY minerals in the water that might build up in your system. The anti-freeze works to keep algae and other ickies from growing in your water.

2. Use a smaller resovoir system (or even closed loop) and install 1 or more radiators found in CPU cooling systems with 120mm fans attached. This will continously cool your water system to ambient room temperatures, but with a tiny resovoir it will be difficult to add things like ice-packs to drop the temps if the ambient is quite hot.

3. Using an industrial coolant system. Overkill and unless your cutting A LOT, this is a very expensive option to take. You can also explore the idea of Peltier cooling but it is extremely expensive electricity/BTU wise compared to an industrial cooler.

Click the link to add information to this solution:
HOW TO COOL THE BLACKTOOTH 40W LASER TUBE

No the ZY plate is part of the machine kit not the head combo kit.

Click the link to add information to this solution:
DOES ZY PLATE COME WITH LASER HEAD COMBO.

Upgrade your mirrors to SI coated mirrors, using a HQ ZnSe lens and even pushing up to a beam expander will all boost power. The ideal order of experimenation for lowest cost would be changing out for a higher quality lens labeled HQ ZnSE lens. Next would be SI mirrors, which will absorb less heat and reflect better, the last would be to use a beam expander which expands the beam, reducing the heat signature on the mirrors and makes a tighter focal width.

Click the link to add information to this solution:
CAN BOOST THE POWER OF MY BLACKTOOTH LASER?

Temperature probe monitor. Very valuable. This keeps you up to date on your coolant temperature levels.

Voltage meter. This will tell you the exact level of voltage/power you are running telling the laser to run at instead of an arbitrary mark on a drawn wheel around your POT.

Ammeter sensitive to 1mA. This will be sure your not over driving your tube and reducing it's life significantly.

Hour meter. This will tell you exactly how long your system has been 'on' giving you a more accurate bead on the length of your tubes life.

Exhaust fan upgrade. The current fan included is 100CFM. You can buy 120mm fans that push 250CFM and I have included a guide on how to go about doing this here. http://buildyourtools.com/phpBB3/viewto ... 8cdd1802bf

To push the exhaust fan even further, if you have the room/power, I would highly recommend investing in a 600+ CFM "Dust Collector" system. 250CFM is still not suffice to draw all the smoke that can come off of 3mm or 1/8 MDF cutting job.

A cutting surface. I bought myself a aluminum 'egg crate' mesh from my local HVAC company. They are used a cover for fluorescent lights and work great for low impact cutting surface. They come in 4'x8' sheets and are easily cut to fit. The other side is if you can find a steel honeycomb cutting bed to fit. These can be quite costly or fairly affordable depending where you are looking. The benefit of a steel honeycomb is you can use high power magnets to hold material down.

Click the link to add information to this solution:
HOW CAN YOU ENHANCE THE BLACKTOOTH LASER CUTTER?

check your in-going power and make sure that you have a good neutral connection. Frequently the issue is not the power supply but the power coming into the power supply that causes the problem. There is a chance that the power is good coming in but there is a loose neutral connection and that causes it. This is the neutral connection that runs all the way back to the panel in your home.

Click the link to add information to this solution:
WHY DO MY 40W LASER POWER SUPPLIES KEEP FAILING?

Shipping crate size 121" X 36" X 92"

Weight 511 LBS

Click the link to add information to this solution:
WHAT ARE THE SHIPPING DIMENSIONS FOR VERTICAL LASER

no, it will only work on anodized aluminum

Click the link to add information to this solution:
WILL THE LASER ENGRAVER WORK ON NON-ANODIZED ALUMINUM

A standard 40W CO2 laser will cut up to 1/4" thick of material, be it wood, acrylic, card stock, leather, fabric, foam, cork, etc. (Decent speed and final cut are heavily dependent on a strong air assist upgrade)

Metals cannot be cut due to the power level and wavelength of the CO2 laser. But it can be marked with special solutions like Cermark or Thermark.

Click the link to add information to this solution:
WHAT THICKNESS OF MATERIAL CAN THE BLACKTOOTH LASER CUT?

The blackTooth Laser cutter and Engraver can be built in a weekend. Take a look at the build instructions and try to determine if you feel you have sufficient capability to put together the laser system.

Click the link to add information to this solution:
HOW DIFFICULT IS IT TO BUILD THE BLACKTOOTH LASER CUTTER?

The Greenbull machine can cut a very wide variety of materials ranging from foam to aluminum. We recommend the use of our 2.2kW spindle to allow the greatest flexibility. Aside from that, the most important thing is to use an appropriate end mill for the material you are cutting and to use appropriate speeds and feed rates.



BYCNC Response:
Our 40W laser can cut up to about 1/4" materials ranging from wood and acrylic down through lighter materials such as leather, fabric, foam, etc. Speed and final cut are greatly enhanced by an air assist upgrade. We also offer an 80W laser which has approximately twice the capabilities of the 40W.

Additional Information:

Click the link to add information to this solution:
WHAT MATERIALS CAN THE GREENBULL MACHINE CUT? LASER ETCH?

If you take the standard parallel cable BoB (Break Out Board), then you will need control software (Mach 3 or EMC2) and CAM software to make your G-Code (such as CamBam). Personally I use CamBam and Mach 3, they work beautifully but don't expect to turn them on and know how they work out of the box. Give yourself a few weeks to get familiar with the basics. CamBam is VERY powerful software for it's price. I'm surprised how much I keep learning on what I can do with it...I highly recommend it if you want as much control as possible.

Mach 3 + CamBam as a bundle costs $310. EMC2 will give you a free replacement for Mach 3 and is exclusively for Linux.

If you use the USB BoB, it will cost an extra $75 + $75 for the software. This is an all-in-one package so no need for Mach 3 or CamBam.

For etching rasters (jpeg, bmp, tiff, non-vectors, photos), I highly recommend PicEngrave. It has been a labor of love for the past 9 years and John has done a wonderful job with it. It easily compares in quality compared to software that is in the $200-$300 range. John's software runs $40 and can be found here: http://picengrave.com/ (don't let the modest website fool you, this stuff can do amazing things). DotG and the Mach3 engrave plugin are two other options and instructions can be found on Dustans page in the gallery on buildyourcnc.com website.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
WHAT SOFTWARE CAN BE USED WITH THE BLACKTOOTH LASER CUTTER?

This video will illustrate how to test for laser power:

Click the link to add information to this solution:
HOW TO KNOW IF THE POWER SUPPLY OF THE LASER TUBE IS DAMAGED