[ Log In ]
[ Register ]

Question #: 14624

Question: how to configure the Z probe using the pokey57cnc controller

Current Solution

If you do the following, you can get mach3 to recognize the probe.

In mach3, go to config, ports and pins, input signals, and scroll down to probe. Check enabled, active low, and emulated. Ignore the ports, pins and keys. They are set automatically.



Go to Mach3 Plugin Control tab, select Configure Pokeys57CNC. Go to pulse engine settings tab, and under the probing input in the lower left corner of the page, scroll down and select Pin 19. Click apply. Close and restart mach 3. When you go to diagnostics page in mach3 after it’s reopened, the digitize light indicates whether the probe circuit is closed. IF it’s lit, it’s closed. IF not, it’s not.

If this information exists anywhere else, I couldn’t find it. I found it through working with poblocks, which also updated my pokeys57cnc firmware.

Respond:

Other Possible Solutions to this Question

  • How do you zero the z axis using a plate with the planet-cnc software and your USB controller?

    The instructions on how to use a plate for z-axis homing (moveable sensor) can be found here:

    http://www.planet-cnc.com/faq/moveable_sensor/

    Click the link to respond:
    How do you zero the z axis using a plate with the planet-cnc software and your USB controller?

  • I am trying to connect my pockeys57cnc usb controller to my mach 3 software. I am totally lost on how to configure it all. Any help?
  • Using the PoKeys57CNC how to you connect two motors to the Y axis and how is Mach 4 configured for this?

    Polabs prepared step by step user guide for PoKeys57CNC and Mach4 to try answering such questions. It is available in our downloads section: https://www.poscope.com/wp-content/uploads/downloads/Pokeys/LibrariesAndPlugins/Mach4 and PoKeys57CNC - step by step guide.pdf

    Click the link to respond:
    Using the PoKeys57CNC how to you connect two motors to the Y axis and how is Mach 4 configured for this?

  • How are limit switches connected to the AWC708 controller?

    If you are using the AWC708 or equivalent laser controller, the limit switches will connect between the EL input terminal and the GND terminal in normally open (NO) connection. Most limit switches can be connected as NO, or normally closed (NC).

    For instance, a limit switch for the X- limit will be connected from the ELX- terminal to the NO connection of the limit switch, then a connection from the GND terminal on the laser controller to the COM connection to the same limit switch.

    Click the link to respond:
    How are limit switches connected to the AWC708 controller?

  • How should I connect the limit switches to my laser controller?

    If you are using the AWC708 or equivalent laser controller, the limit switches will connect between the EL input terminal and the GND terminal in normally open (NO) connection. Most limit switches can be connected as NO, or normally closed (NC).

    For instance, a limit switch for the X- limit will be connected from the ELX- terminal to the NO connection of the limit switch, then a connection from the GND terminal on the laser controller to the COM connection to the same limit switch.

    Click the link to respond:
    How should I connect the limit switches to my laser controller?

  • how to control the spindle with the usb controller

    To control a spindle using the USB CNC interface, you will need a relay board that contains a transistor that can activate the relay with a power source with enough current that can activate the relay. This video explains all of the information you will need to develop this relay circuit:

    &index=44&list=PLE72E4CFE73BD1DE1

    Click the link to respond:
    how to control the spindle with the usb controller

  • How can I connect an inductive proximity sensor to the Mach3 USB controller?

    I would suggest using the NPN proximity sensor for the Mach3 USB or the Pokeys57cnc. The proximity sensors have a top DC voltage limit of 30 volts, so it would be best to use the 24V power supply that is used to power the controller. Both controllers have a 24V power requirement, so that is convenient.

    The blue wire of the proximity sensor is the GND wire and is connected to the 24V power supply's V- terminal. The brown wire is the positive wire and is connected to the V+ terminal of the 24V power supply. The black wire is the signal wire and is connected to the input terminal of the controller.

    Click the link to respond:
    How can I connect an inductive proximity sensor to the Mach3 USB controller?

  • When using the laser controller, what does "engrave beyond border limit" mean?

    LaserCAD: Engrave beyond border limit.

    This is caused by a sweeping motion that is too fast and where the acceleration is too slow. My recommended action would be to keep the acceleration the way it is and slow down the speed of the engrave sweeping motion. I typically use around 200-300 mm/sec and make sure that the axis sweep motion is the nozzle along the gantry, not the gantry itself. The gantry will have too much inertia to sweep, but the nozzle is very light and can sweep very quickly.

    Specifically, what is happening with the engrave beyond border limit is where that axis is not able to slow down fast enough to not hit the border. For instance, imagine a car going 100 mph and it needs to stop within 30 feet. This would not be possible because the deceleration is not high enough.

    Additional Information:
    Why always showing trigger limits when starting

    Additional Information:
    Why always showing trigger limits when starting

    Click the link to respond:
    When using the laser controller, what does "engrave beyond border limit" mean?

  • How can I connect the Pokeys57CNC controller to a DRV8825 / A4988 expansion board?

    The DRV8825 driver IC by TI (Texas Instruments) has two main connections called STEP and DIR. These are the two main connections that you need to use to connect to the Pokeys57CNC controller. You also need to connect the positive digital voltage pin (5V) from the Pokeys57CNC controller's motor connector to both the reset and sleep pins. The GND pin from the Pokeys57CNC motor connector is connected to the GND pin of the DRV8825 driver. The enable pin of the DRV88525 can remain unconnected.

    There is a trimmer potentiometer on the DRV8825 that can increase or decrease the amperage setting for the motor. Depending on the DRV8825 board you purchased, there may be two pads to determine the amp setting while turning the trimmer (in the voltage setting on your multimeter).

    The A1 and A2 is connected to one of the motor's coils and B1 and B2 is connected to the other motor's coil. There is a pin on the DRV8825 called VMOT that you will connect to the power supply (max 45VDC) and the GND pin next to the VMOT is the V- for the same power supply.

    I hope this helps. If not, please add additional information on this thread.

    Additional Information:
    I followed (to the best of my ability) the instructions provided to my original question, but I did not receive successful results. When I followed the instructions and connected the ground pin from the Pokeys57CNC motor connector to the DRV8825 / A4988 expansion board, it stops the communication between the Pokeys57CNC board & the motors 1-3 that I had working previously. The DRV8825 / A4988 expansion board will be the fourth driver I am connecting to the Pokeys57CNC. The previous three drivers are PoStep-60's if that helps understand the issue.

    Prior to hooking up the ground pin (I used pin 10 from the Pokeys57CNC motor connector) to the DRV8825 / A4988 expansion boards ground pin, I was able to see the power being applied via the red LED being illuminated on the DRV8825 board; after this new configuration the light is not turning on.

    With the new recommended setup, I used a heat shrink solder piece to add the shunt for the connection to the sleep pin. The connection to the sleep pin is where I believe my issues are stemming from. I must be connecting it to the incorrect pin (within the 9 pin layout on the DRV8825 / A4988 expansion board). Do you have any reference to the 9 pin pinout on the A4988 expansion board? I double checked the pinout provided on the Texas Instruments page, but it only gives clarity to the pinouts on the DRV8825 board itself. After reviewing their documentation, I tried connecting the 5v (pin 9 from the Pokeys57CNC motor connection that's split to connect with the reset pin on the DRV8825 / A4988) wire directly to the terminal on the DRV8825 board and that didn't work either.

    Any help or clarification you can provide would be greatly appreciated!

    Click the link to respond:
    How can I connect the Pokeys57CNC controller to a DRV8825 / A4988 expansion board?

  • I get a "communicating unsuccessful" when using LaserCAD and the AWC608 Laser controller

    If you are getting the "Communicating Unsuccessful!" error when you are trying to communicate between LaserCAD and the AWC608 Laser Cutter and Engraver controller (after you have already tried installing the USB driver from the LaserCAD setup procedure), these are the steps you will need for a successful communication:

    - Open the Device Manager window (right click on the start menu and select Device Manager)
    - When you plug the USB cable from the AWC608 Laser Cutter Controller (USB Type B connector) to the computer, you should see a new item in the Device Manager, possibly under "Ports (COM & LPT)", or under "Other Devices". It may show as an item under "Other Devices", possibly FT245R and has an "!" in a yellow triangle.
    - Download the latest FTDI drivers from: http://www.ftdichip.com/Drivers/D2XX.htm
    - Unzip the files to a folder that can be easily browsed.
    - Right click on the item that appeared in the Device Manager when the cable was plugged in between the Laser Cutter AWC608 controller and the computer.
    - Click on update driver
    - Select the procedure to manually install the driver and browse to the folder containing the FTDI driver and follow the step in the driver installation wizard.
    - The item should now be located under the "Ports (COM & LPT)" and should be named "USB Serial Device (COM#)". The # will be the number you will use in the LaserCAD software.
    - In the LaserCAD software, click the "Select Mode" at the far top right of the Laser CAD user interface.
    - Make sure USB mode is selected.
    - If the Machine name with the correct COM number is listed, select it and exit the dialog window. Otherwise, click on "Add" and fill in the details with the new COM number.

    Additional Information:


    Additional Information:
    Communicating unsuccessful

    Additional Information:
    Communicating unsuccessful

    Click the link to respond:
    I get a "communicating unsuccessful" when using LaserCAD and the AWC608 Laser controller

  • I trying to setup your USB Controller card. The planetcnc does not load the card, no driver for usb card. Using windows 8.1.

    To install the USB breakout board, there will be no driver to install nor any pop-up will be viewed in your windows task-bar, except only to notify that a USB device has been connected.

    If you have planet-cnc installed it should automatically ask for a license number, which if you don't have you will continue without entering any numbers. Please read carefully since there is a pop-up that can erase the entire firmware on your board, and you will basically have a dead board.

    Please email customerservice@buildyourcnc.com for further assitance.

    Additional Information:
    For Windows 8.1 you need to follow special driver installation steps. Download Planet-cnc software MANUAL and scroll down to that paragraph (without it you will not be able to install and use your board).

    Click the link to respond:
    I trying to setup your USB Controller card. The planetcnc does not load the card, no driver for usb card. Using windows 8.1.

  • How do you install the software for the Mach3 USB controller?

    The Mach3 usb controller/interface has instructions and videos on this page:
    https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

    There is a 5 step process on that page to install the plug-in and the configuration xml file that is necessary for the proper functioning of the controller.

    The videos on that page also demonstrate in detail how to install the software, plug-ins, xml file and wiring and testing most of the features of the Mach3 USB interface.

    Hope this helps.

    Click the link to respond:
    How do you install the software for the Mach3 USB controller?

  • How do I use the outputs on the Mach3 USB controller?

    I created a video to demonstrate how to use the outputs on the Mach3 USB controller. You can find this video on the following page:
    https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

    Scroll down to the 5th video on that page. The title of the video is: Mach3 USB Controller Outputs

    Click the link to respond:
    How do I use the outputs on the Mach3 USB controller?

  • how to connect USB controller to the drivers. Any instructions/video other then html datasheet?
  • Using USB Controller Board with Planet-CNC software. The S/W recognizes limit switches but not soft limits. Help?

    "Soft limits are used to decelerate machine to stop before machine is stopped hard way at limit switch or before it crashes. I recommend "Soft Limits Decelerate" and "Soft Limits Strict" settings are also checked. Sometimes we need to disable soft limits and there is a command for this in menu "Machine/Soft Limits". When soft limit is triggered position display will be yellow."

    Are the soft limits "grayed out"?
    Here is a link to a very useful forum post from the Planet-CNC crew:
    http://www.planet-cnc.com/faq/machine_setup/



    Additional Information:
    i keep getting scratches when engraving pictures on dog tags

    Click the link to respond:
    Using USB Controller Board with Planet-CNC software. The S/W recognizes limit switches but not soft limits. Help?

  • 3d printer motors not moving fast enough. How should I configure the motor drivers?

    This will depend on the 3D printer that you are using and the mechanics involved. Specifically regarding the motor drivers, software is really what determines the speed of the motor. If the computer is not able to product the high number of pulses that is required for faster motion, then you can reduce the microstepping and configure the software appropriately for the new microstepping so the resolution is corrected (steps/inch or steps/mm).

    Click the link to respond:
    3d printer motors not moving fast enough. How should I configure the motor drivers?

  • My stepper motors are randomly and frequently stalling while using the Pokeys57CNC controller board, any idea what could be the issue?

    I would suspect that the velocity and/or acceleration is too high for the amp setting on the driver. Consider increasing the current amp setting on the driver is the motor can handle the current, or decrease the velocity and/or acceleration.

    You might also want to check to see if you have any mechanical binding on the machine. To check, remove the mechanical drive mechanism so the axis slides freely and slide it from end to end to feel if you have any tight areas or binding.

    Click the link to respond:
    My stepper motors are randomly and frequently stalling while using the Pokeys57CNC controller board, any idea what could be the issue?

  • What software is needed to run the laser controller from the PC?

    The laser controller uses software called LaserCAD. You can find the link to the LaserCAD software on the Laser Controller product page:

    https://www.buildyourcnc.com/item/Laser-Component-Laser-Control-System

    Click the link to respond:
    What software is needed to run the laser controller from the PC?

  • I there a tutorial on hooking up a Z axis zero touch plate to the usb controller?

    To use a touch plate on any controller, all you need is a conductive flat material with a known thickness and some wire and alligator clips. Solder a wire to the touch plate and connect the other end of the wire to the free input terminal of the controller. Connect a wire with an alligator clip to the ground of the controller (on the Mach3 USB controller, this ground is the DCM terminal, or the digital gnd on the 24VDC power supply). Connect the alligator clip to the end mill.

    You can either use a script to serve as the probe, or you can use the ref all home button and setup the touch plate as a home switch.

    Click the link to respond:
    I there a tutorial on hooking up a Z axis zero touch plate to the usb controller?

Get Help with:
This Product
Orders
Tech Support
Sales
This Product
Order Query
Tech Support
Sales
Not logged in. Log In Register
Track Order(s)
View Order(s)
I Want to Schecule a One-On-One Paid Tech Support Session
Book an Appointment Pertaining to a BuildYourCNC Product (Free)
Ask a Quesion Below (Free):
Book an Appointment Pertaining Other Equipment ($60/half hour)
Book an Immedite Appointment Pertaining Other Equipment ($120/half hour)
Ask a Quesion Below (Free):
Waiting for response... I may not answer immediately, but I was notified on my cellular phone so my response is forthcoming. If I don't respond immediately, you can always go to the [My Account] page to see all of our chats at any time.