The pulse stream is output directly from the onboard microcontroller on the Mach3 USB controller, so there is no need for a safety charge pump from the computer to the controller. Parallel port breakout boards were connected to the computer via GPIO pins (General Purpose Input/Output) and each pin dedicated to the step pulse would be output directly from those pins. In that case, a safety charge pump was needed.

Additional Information:
20

Additional Information:
20

Click the link to add information to this solution:
[575] Can it control a safety charge pump ?

Yes, the Mach3 USB controller can work with the Gecko G540 drives.

Here are the connections you will need from the Mach3 USB controller to the G540:
XP terminal to Pin 2 of the DB25 LPT connector
XD terminal to Pin 3 of the DB25 LPT connector
YP terminal to Pin 4 of the DB25 LPT connector
YD terminal to Pin 5 of the DB25 LPT connector
ZP terminal to Pin 6 of the DB25 LPT connector
ZD terminal to Pin 7 of the DB25 LPT connector
Any pins from 18 through 25 can be connected to the GND terminals next to the XP terminal.

Pins 10 through 13 can be connected to IN1, IN2, IN3, and IN4.

Click the link to add information to this solution:
[575] Can this card work with a gecko g540?

You can use the mach3turn in the mach3 loader and simply enable the motor outputs. For the inputs and outputs, make sure to use port 3 for the port number and reference the terminal description for the pin number (i.e. IN2 is Pin 2). Don't forget to use the plug RNRMotion.dll in the plugins folder first.

Click the link to add information to this solution:
[575] Where can i find a xml file for maxh3turn?

To use a touch plate on any controller, all you need is a conductive flat material with a known thickness and some wire and alligator clips. Solder a wire to the touch plate and connect the other end of the wire to the free input terminal of the controller. Connect a wire with an alligator clip to the ground of the controller (on the Mach3 USB controller, this ground is the DCM terminal, or the digital gnd on the 24VDC power supply). Connect the alligator clip to the end mill.

You can either use a script to serve as the probe, or you can use the ref all home button and setup the touch plate as a home switch.

Additional Information:
I connect wire to cmd- and to in2. I cant getbit to work, what arecthe corresponding ports and pins to usenin mach3? Please help.

Click the link to add information to this solution:
[575] Can you tell me where to find a script (for Auto Tool Zero button) to zero Z axis from a touch plate?

Yes, this CNC controller can be used with closed-loop stepper drivers and motors. The loop for control and feedback is between the driver and the motor. The closed-loop driver receives step and direction signals, which this controller will output which furnishes the driver with the necessary signals to move the motor. Additionally, the closed-loop driver can output a fault signal to this controller through the controller's input terminals in case the motor should encounter a situation that prevents the motor from moving so the CNC can shut down.

Click the link to add information to this solution:
[575] Hi, Can I use this board with a closed loop stepper?

I have not tried using the handwheel inputs for anything other than for handwheel operation. I haven't had success using a THC with the Mach3 USB controller. The pokeys57CNC controller is a better solution for THC (torch height controller) and plasma cutter use.

Here is a link to the okeys57CNC controller: https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Click the link to add information to this solution:
[575] can the handwheel inputs be used for thc

In theory, utilizing a 5V reference in the 10V terminal of the Mach3 USB controller should yield functional results, although I haven't personally tested this configuration. If you possess an oscilloscope, you can monitor the PWM signal to verify whether the AVI output achieves a peak 5V PWM square wave.

Click the link to add information to this solution:
[575] Can it make the spidle control PWM to a VFD witch 5 V input

Yes, the Mach3 USB controller will work with the latest Windows version and in 64-bit mode. The 32-bit mode is only relevant for using the parallel port driver if you are using a parallel port breakout board. Since this controller is connected via a USB cable, the 64-bit state will work fine.

Additional Information:
mach3 not showing in device manager

Click the link to add information to this solution:
[575] I have a 64 bit Windows 11 laptop. Will this interface board work with this? If not is there an option you can suggest.

The power supply that is used to power this controller must be 24VDC maximum. Any higher voltage and the controller components can be damaged. The 24VDC power supply doesn't need to be a high amp power supply. I would recommend This power supply: https://buildyourcnc.com/item/electronicsAndMotors-power-supply-24v-1a-dc

Click the link to add information to this solution:
[575] Instructions read 24v on the card, can it support 36vdc ?

You can use two MGPs (bare MPGs) to provide independent axis control. The handwheel input on this controller contains discrete inputs for the X, Y, Z, and A axes. These inputs can receive a pulse to move their axis. For instance, you can connect an MPG to the X-axis pin and the wheel will move the X-axis only.

Of course, if you have a traditional pendant, you can move any axis independently from only a single wheel with a switch that selects the axis you wish to move.

Click the link to add information to this solution:
[575] can we use two MPG for two axis independant axis movement

You can determine if the country is serviceable by:
- selecting the items you want to purchase on the website
- go to the cart (shopping cart top left of any webpage)
- log in, or register
- Enter the address and click on calculate shipping.

The webpage will return the direct rates and whether your area is serviced or not. Feel free to enter any address as long as you are able to receive the package from that address.

Click the link to add information to this solution:
CAN YOU SHIP ITEMS TO MY COUNTRY?

Yes, you can use a conductive metal to serve as a zeroing block for the Z axis. All you need to do is connect the block (conductive metal) to one of the 4 inputs on the controller. The end mill must be connected to the DCM terminal (the GND of the 24V power supply) of the controller. In the inputs dialog box (config-ports and pins-inputs). Under the probe line, enter port 3 and the pin used for the block.

Click the link to add information to this solution:
[575] Hi can I use a zeroing block with mock three interface board and do you have one I can purchase and directions on how to set up

Open the input signals dialog box by clicking on config, then ports and pins, then input signals. For each line item that you use (i.e. x++, y--, etc) make sure the port number is 3.

Also, make sure there is a 24v power supply connected to the DCM and 24V terminals. One side of the NO on the limit switch must connect to the DCM, or the power supply V- terminal.

Additional Information:

Click the link to add information to this solution:
[575] I cannot get the limits to work I’m normally open as you state

You can determine if the country is serviceable by:
- selecting the items you want to purchase on the website
- go to the cart (shopping cart top left of any webpage)
- log in, or register
- Enter the address and click on calculate shipping.

The webpage will return the direct rates and whether your area is serviced or not. Feel free to enter any address as long as you are able to receive the package from that address.

Click the link to add information to this solution:
CAN YOU SEND PRODUCTS TO MY COUNTRY?

You can determine if the country is serviceable by:
- selecting the items you want to purchase on the website
- go to the cart (shopping cart top left of any webpage)
- log in, or register
- Enter the address and click on calculate shipping.

The webpage will return the direct rates and whether your area is serviced or not. Feel free to enter any address as long as you are able to receive the package from that address.

Click the link to add information to this solution:
CAN YOU SHIP TYO MY COUNTRY?

Yes, that driver has standard step and direction signal terminals that will work fine with the Mach3 USB controller.

Click the link to add information to this solution:
[575] We have Gecko 203V that require 5v input signal, can this be done?

Temperature probe monitor. Very valuable. This keeps you up to date on your coolant temperature levels.

Voltage meter. This will tell you the exact level of voltage/power you are running telling the laser to run at instead of an arbitrary mark on a drawn wheel around your POT.

Ammeter sensitive to 1mA. This will be sure your not over driving your tube and reducing it's life significantly.

Hour meter. This will tell you exactly how long your system has been 'on' giving you a more accurate bead on the length of your tubes life.

Exhaust fan upgrade. The current fan included is 100CFM. You can buy 120mm fans that push 250CFM and I have included a guide on how to go about doing this here. http://buildyourtools.com/phpBB3/viewto ... 8cdd1802bf

To push the exhaust fan even further, if you have the room/power, I would highly recommend investing in a 600+ CFM "Dust Collector" system. 250CFM is still not suffice to draw all the smoke that can come off of 3mm or 1/8 MDF cutting job.

A cutting surface. I bought myself a aluminum 'egg crate' mesh from my local HVAC company. They are used a cover for fluorescent lights and work great for low impact cutting surface. They come in 4'x8' sheets and are easily cut to fit. The other side is if you can find a steel honeycomb cutting bed to fit. These can be quite costly or fairly affordable depending where you are looking. The benefit of a steel honeycomb is you can use high power magnets to hold material down.

Click the link to add information to this solution:
HOW CAN YOU ENHANCE THE BLACKTOOTH LASER CUTTER?

To select a 4 axis NEMA 17 motor and driver combination, you will need the following:

- Four (4) NEMA 17 motors: https://buildyourcnc.com/item/electronicsAndMotors-nema17-62ozin-NEWBIEHACK-motors-stepping_motor-62_ozin

- Four (4) drivers, either the 2.5A: https://buildyourcnc.com/item/motion%20electronics-steppermotordriver-newbiehack-Motor_Drivers-2!5_Amp_modular or the 3.0A: https://buildyourcnc.com/item/electronicsAndMotors-stepper-driver-3!0a

- One (1) Power supply, either the 24V or 36V (recommended): https://buildyourcnc.com/item/electronicsAndMotors-power-supply

- Finally, an interface is needed, either parallel, or USB. The USB works with planet-cnc software only. The parallel interface works with all major CNC control software: https://buildyourcnc.com/category/breakout

Click the link to add information to this solution:
Can you supply a quote for a 4 axis combo kit with NEMA 17 Motors

There are 4 separate input terminals on the controller. However, you can add an unlimited number of sensors and switches to these inputs using a parallel wiring scheme for normally open circuits and a serial wiring scheme for normally closed circuits.

Check out this video where I explain these wiring schemes in detail:

Click the link to add information to this solution:
[575] how many inputs on mach3