[ Register ]

### Question #: 2235

Question: Are these the droids I'm looking for?

Current Solution

We do not have the droids you are looking for, I would search Tatooine for better droid selection.

Respond:

### Other Possible Solutions to this Question

• WHAT ARE THE CABLE LENGTHS FOR BLACKTOE

The motor cables for the blackToe are as follows:

Total 30 feet

X - 9
Y - 10
Z - 11

WHAT ARE THE CABLE LENGTHS FOR BLACKTOE

• WHAT CABLE LENGTHS ARE USED FOR THE BLACKTOE

The motor cables for the blackToe are as follows:

Total 30 feet

X - 9
Y - 10
Z - 11

WHAT CABLE LENGTHS ARE USED FOR THE BLACKTOE

• WHAT ARE THE DIMENSIONS FOR GREENBULL TABLE?

Actual table dimension: 4'x8' is 56.078"x 121.50" (the overhang in the illustrations should be 3/4" thick)
To determine the frame dimensions, first consider using the frame height shown of almost 3' (2.86'). The width of the frame should be 4" narrower than the dimension from rail edge to rail edge (6X rail to rail is 80.078"). This will provide a 2" overhang on both sides (4X frame width should be 56.078").
The length of the frame should be 4" shorter than the desired length of the rails to provide a 2" overhang on both ends. The travel length will be 20" shorter than the rail length due to the space occupied by the gantry sides.
Two long pieces of 3/4" material will need to be placed on top of the frame with the 2" overhang on the sides and the end. These long strips of material will receive the rails and the chain mounts on the ends.

https://www.buildyourcnc.com/Item/cnc-machine-greenBull-v4-4X

WHAT ARE THE DIMENSIONS FOR GREENBULL TABLE?

• WHAT ARE THE SHIPPING DIMENSIONS FOR GREENBULL?

76" X 40" X 26"
230 LBS

WHAT ARE THE SHIPPING DIMENSIONS FOR GREENBULL?

• WHAT ARE THE ROLLER CHAIN LENGTHS FOR GREENBULL 4X

The roller chain lengths for the greenBull 4x is:
- 13 feet for each side of the X axis (total of 26 feet), and
- 6 feet for the Y-axis

WHAT ARE THE ROLLER CHAIN LENGTHS FOR GREENBULL 4X

• WHAT ARE THE SHIPPING DIMENSIONS FOR VERTICAL LASER

Shipping crate size 121" X 36" X 92"

Weight 511 LBS

WHAT ARE THE SHIPPING DIMENSIONS FOR VERTICAL LASER

• THESE MACHINES ARE DANGEROUS, WHAT DO DO?

These machines are inherently dangerous. Before the machine moves, the machine should be clear of any person by a dimension of at the distance of a persons reach plus a few more feet. This is the policies we institute in our shop and what is recommend to all of our customers. Treat these machines as you would treat any major power tool in the shop.

With that said, you can certainly add some protective parts, but still keep folks away even with those installed. I would use the gantry side to do all of the mounting of the protective parts. Consider using sheet metal that you can bend and make a simple installation right on the gantry side.

THESE MACHINES ARE DANGEROUS, WHAT DO DO?

• HOW DO ADDRESS THE DANGER OF THESE CNC MACHINES

These machines are inherently dangerous. Before the machine moves, the machine should be clear of any person by a dimension of at the distance of a persons reach plus a few more feet. This is the policies we institute in our shop and what is recommend to all of our customers. Treat these machines as you would treat any major power tool in the shop.

With that said, you can certainly add some protective parts, but still keep folks away even with those installed. I would use the gantry side to do all of the mounting of the protective parts. Consider using sheet metal that you can bend and make a simple installation right on the gantry side.

HOW DO ADDRESS THE DANGER OF THESE CNC MACHINES

• WHERE ARE THE WIRING DIAGRAMS FOR BLACKTOOTH LASER CUTTER IN INSTRUCTIONS?

You can find the wiring diagrams for the blackTooth on step 105 and 106 on the list of instructions on the blackTooth page. Step 105 pertains to the parallel breakout board and step 106 pertains to the USB interface board.

wire size

WHERE ARE THE WIRING DIAGRAMS FOR BLACKTOOTH LASER CUTTER IN INSTRUCTIONS?

• ARE THERE RECOMMENDATIONS FOR THE PREVENTION OF INSTITUTIONAL OUTBREAKS INFLUENZA?

The most important factor in preventing outbreaks is annual vaccination of all occupants of the facility, and all persons in the facility who share the same air as the high-risk occupants. Groups that should be targeted include physicians, nurses, and other personnel in hospitals and outpatient settings who have contact with high-risk patients in all age groups, and providers of home care to high-risk persons (e.g., visiting nurses, volunteers).

ARE THERE RECOMMENDATIONS FOR THE PREVENTION OF INSTITUTIONAL OUTBREAKS INFLUENZA?

• I’M LOOKING TO PURCHASE SPINDLE AND VFD WAS CURIOS IF THE SPINDLES COME WITH COLLETS SO WHICH ONES?

Yes, all of the spindles come with collets. The collets have a 1/4" (6.35mm) bore for end mills that have a 1/4" shank. The ER specification is different for the 1.5kW (ER-11) and the 2.2kW (ER-20).

I’M LOOKING TO PURCHASE SPINDLE AND VFD WAS CURIOS IF THE SPINDLES COME WITH COLLETS SO WHICH ONES?

• MY PARTS ARE COMING OUT THE WRONG SIZE

In Mach3, go to the Settings Tab, and select "Set Steps Per Unit". It will ask you how far to move the machine. Before you do this, make a mark on the table exactly where the end mill is resting. You can do this by lowering the end mill until it touches the material, then spinning it by hand to cut a small dimple in the material. Then, raise the end mill to clear the material, and assign a distance to move the machine. Once the machine moves and stops, measure the exact distance that it actually traveled with a tape measure, and enter this value into the dialog box that asks how far it moved. Mach3 will automatically adjust your steps per unit for that axis to be more accurate. Do this for all axes often to ensure you are cutting accurately. The longer distances you use calibrate, and the more precise you are with your measurements, the better.

idwmHJym

-1 OR 2+78-78-1=0+0+0+1 --

-1 OR 2+135-135-1=0+0+0+1

-1' OR 2+886-886-1=0+0+0+1 --

-1' OR 2+357-357-1=0+0+0+1 or 'xkLzGxAb'='

-1" OR 2+279-279-1=0+0+0+1 --

1'"

1����%2527%2522

@@5fZce

MY PARTS ARE COMING OUT THE WRONG SIZE

• HOW MUCH MOTOR CABLE FOR THE BLACKFOOT?

The motor cables for the blackToe are as follows:

Total 30 feet

X - 9
Y - 10
Z - 11

HOW MUCH MOTOR CABLE FOR THE BLACKFOOT?

• WHAT IS THE LEAD TIME FOR BLACKTOE?

You can expect a one week lead time for our machines.

WHAT IS THE LEAD TIME FOR BLACKTOE?

• WHAT IS THE LEAD TIME FOR BLACKFOOT

You can expect a one week lead time for our machines.

WHAT IS THE LEAD TIME FOR BLACKFOOT

• WHAT ARE CHINA PRICES FOR COLLETS?

From: Milan Shah
ACCU-FIX Precision Tools Pvt Ltd
458, Manjusar GIDC, Savli, Vadodara, Gujarat, India
Mobile: +(91) 7567975718

ER 11 - STD. Precision Collet \$3.61 - No 1/2" shank sizes.
ER 16 - STD. Precision Collet \$4.05
ER 20 - STD. Precision Collet \$4.27
ER 25 - STD. Precision Collet \$4.34
ER 32 - STD. Precision Collet \$4.69
ER 40 - STD. Precision Collet \$5.32
---------------------------------------------------------------

WHAT ARE CHINA PRICES FOR COLLETS?

• WHAT IS THE LEAD TIME FOR REDFROG?

You can expect a two week lead time for the redFrog pick and place machine.

WHAT IS THE LEAD TIME FOR REDFROG?

• WHERE ARE THE ELECTRONICS WIRING VIDEOS?

The blackFoot CNC machine kit does not include a table. The table can be made as long or shot as you need. for instance, if you are looking for a travel of 4 fet x 4 feet, then the table will need to be about 6 feet long to get the full 4 feet of travel.

The electronics are very straight forward using the connection diagram for the breakout board that you select. Use the videos for a general idea and then use the connection diagram to verify the correct connections for the interface of your choosing.

Yes,the USB interface replaces the breakout board, but remember that you will need to use the planet-cnc software with the USB interface.

The electronics does accompany the cnc machine kits as long as you select the option "with electronics". There are option to purchase the machines without electronics and that would be necessary if you either have your own electronics, or you prefer the plug and play cnc computer system we call the redLeaf, or redSprout. This will also be necessary if you prefer the electronics that use the USB interface rather than the parallel interface.

WHERE ARE THE ELECTRONICS WIRING VIDEOS?

• WHERE ARE THE ELECTRONICS WIRING VIDEOS?

The electronics and wiring videos are located under the tutorials section (click Tutorials on the top menu. The Title is "CNC Electronics and Wiring". The actual link to these videos is: https://www.buildyourcnc.com/CNCElectronicsandWiring.aspx

You will also find the electronic wiring videos for the USB controller at: https://www.buildyourcnc.com/tutorials/tutorial-Electronics-USB-Interface-Wiring

WHERE ARE THE ELECTRONICS WIRING VIDEOS?

Get Help with:
This Product
Orders
Tech Support
Sales
This Product
Order Query
Tech Support
Sales