If your computer does not have a parallel port, all you will need is a low cost PCI parallel adapter card (these can be found on amazon for $15-$20). If you plan on using a laptop (not recommended) you can try to find a PCMCIA parallel adapter, but many people have frequent issues with this setup. A more expensive solution would be to purchase a USB smooth stepper board. Unfortunately, we do not supply any of these adapters and cannot attest to their reliability.

Additional Information:
ur gay

Additional Information:

Click the link to add information to this solution:
MY COMPUTER DOES NOT HAVE A PARALLEL PORT. HOW DO I INTERFACE WITH THE BREAKOUT BOARD?

For our parallel breakout board (https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay#prettyPhoto/2/) the schematic will show the connections going from the BB to the drivers. The parallel breakout board uses the 25 pin parallel connection to communicate from the computer to drivers, and the USB is used to power the main-board itself, supplying 5V.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
I am wiring my breakout board and it has a USB port on it. Is the USB port there to supply the 5 volt power to it?

Yes, you can connect a THC, Torch Height Controller, with the Mach3 USB controller. The THC uses the inputs to determine if the z axis needs to move up or down according to the arc of the plasma torch. The THC connects its outputs to the inputs of the controller so the controller will be informed of the states of the plasma torch.

Click the link to add information to this solution:
I am installing a mach 3 usb controller into a wright cnc plasma table and I need instruction on wiring the thc (proma compact ) torch height controller to this board. IE will this board work to replace the parallel port board with usb controller board?

You can add a limit switch to either the USB or the parallel board. Please refer to the product pages for these items to view wiring diagrams.

Click the link to add information to this solution:
I want to add limit switches but I have no connections on the breakout board. Can I use a usb interface board for the limit switches as well as the parallel port for the running?

You can add a limit switch to either the USB or the parallel board. Please refer to the product pages for these items to view wiring diagrams.

Click the link to add information to this solution:
I want to add limit switches but I have no connections on the breakout board. Can I use a usb interface board for the limit switches as well as the parallel port for the running?

You can find instructions for the Mach3 USB here:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

You will probably need to use the Mach3 USB board with Mach3. We have not tested the Mach3 usb card with Mach4.

Click the link to add information to this solution:
Whereb can I find directions on how to install the Mach3 USB board with Mach 4 software? I do not have a parallell port.

For safety's sake I would recommend a new board because they are inexpensive compared to the electronics that they support. Alternatively, it's possible that the one dead pin is a simple fix, such as a bad connection or solder joint; if you feel comfortable making those repairs then it could be worthwhile to check. Finally, if you are not using all the input pins, you could continue to operate the limit switch on pin 11 and hope for the best.

Click the link to add information to this solution:
I have a breakout board and it appears that the pin 12 connection has failed: when i move my limit switches to pin 11 they work; they don't work on pin 12. Do i need a new breakout board?

Here is how to connect your router to the parallel breakout board through the on-board relay. You will need a spare extension cord. You will need to remove a portion of the outer jacket of the extension cord to expose the white, black and green wires (white = neutral, black = live and green = ground), understanding that the neutral and live create the completed circuit.

See this image of a similar connection. The terminal has the same connections.
https://www.buildyourcnc.com/images/vacuum-pressure-controller-relay-terminals-700.JPG

Image of the relay terminal:
https://www.buildyourcnc.com/images/breakoutboardrelayNONC.PNG

The live/black wire would be cut and one end of the cut would be secured into the P terminal and the other cut end would be secured into the S terminal. The live and ground wire would be uncut and travel from the plug to the router.


Additional Information:
You can also connect other high powered devices to the breakout board using any of the output terminals. You will need to supply extra relays like the one shown here:
https://www.buildyourcnc.com/item/electronicsAndMotors-breakout-Relays-relay-board-250V-12A-5V

Or you can find SSRs (Solid State Relays) that will accept 5v to drive the relay coil. Make sure the SSR will protect the 5V line from Back EMF as there is a coil in the relay. The one we sell contains a fly-back diode to protect the 5v terminal.

Click the link to add information to this solution:
I have your breakout board with relay parallel port , how can I wire up a regular router to that board so I can control the router

For the USB controller and reversing the rotation for a motor, you would need to do this in the software (planet-cnc). In the configuration, you will need to reverse the direction by inverting the direction output.

Technically, the motor changes direction when the direction signal changes from a high to a low, or vice verse. For instance, the motor turns in one direction when the direction signal is, say, low. The motor will turn in the other direction when the direction signal is high. High is 5v and low is 0v or gnd.

Click the link to add information to this solution:
I have wired the step motors with the USB breakout board. When I jog the y axis it travels in the wrong direction. How do i switch the motors rotation?

The breakout board has a relay installed and uses the terminals labeled S, O and P. The following link explains the operation of this relay and how to connect the terminals:
https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay#prettyPhoto/8/

You will run your power cord (use an extension cord rather than the actual power cord of the router) through the relay using the S, O and P. The P is a general connection and the S is normally closed (S and P is connected when the relay is not engaged) and O is normally open (O and p are not connected until the relay is engaged).

There are three wires in the power cord: neutral (white), live (black) and earth ground (green). You will run your neutral wire (white wire) through this terminal. At some point in the power cord, remove the outer insulator and expose the three wires within. Cut your neutral wire and strip both ends of the cut. Then insert one end in P and the other end in O (normally open), so Mach3 or other control software you are using will engage the relay and the router will turn on.

You will need to setup your control software to turn on the relay using Pin #16 as this is the digital signal pin that controls the relay.

Click the link to add information to this solution:
What do I need to do to my breakout board to turn the router motor on at the beginning of the program and off at the end?

Unfortunately no. The parallel port allows for digital signals to be output from 17 pins simultaneously (in parallel). Parallel port adapters tries to achieve this by receiving instructions in a two wire (USB) data signal and convert that to 17 disparate signals. This type of data transmission is too slow for the drivers of a CNC machine or router.

Click the link to add information to this solution:
can i use a usb to parallel port adapter to connect breakout board to computer? (using mach 3)

Any of the following power supplies will be fine for powering the Mach3 USB controller:
https://www.buildyourcnc.com/item/24v

however, the limit switches do not need high current, so the following power supply is sufficient for the task of connecting limit switches:
https://www.buildyourcnc.com/item/electronicsAndMotors-power-supply-24v-1a-dc

Click the link to add information to this solution:
What power supply do you recommend for the spindle and limit switches if I buy the USB Mach3 breakout board?

No, you should not have received two parallel breakout boards in your CNC kit. You can return the extra item using standard shipping with COD. Our apologies for the confusion and the inconvenience.

I will answer the other question as another FAQ. Please check the Customer Service page to see the answer to that question.

If you have difficulty finding the answer, here is a link:
https://www.buildyourcnc.com/FAQ/13636

Click the link to add information to this solution:
I HAVE A 2000 WK 11–3 Z LIMIT SWITCHES GOING TO C10R10 BREAKOUT BOARD . CAN ALSO USE THEM AS MY HOME POSITION WELL. NEED THE WIRING CONFIGURATION

If your computer does not have a parallel port, all you will need is a low cost PCI parallel adapter card (these can be found on amazon for $15-$20). If you plan on using a laptop (not recommended) you can try to find a PCMCIA parallel adapter, but many people have frequent issues with this setup. A more expensive solution would be to purchase a USB smooth stepper board. Unfortunately, we do not supply any of these adapters and cannot attest to their reliability.

Additional Information:
ur gay

Additional Information:

Click the link to add information to this solution:
I have a parallel. breakout board. and no parallel port at the back of my computer do those parallel. cards. work with the breakout board?

No, you should not have received two parallel breakout boards in your CNC kit. You can return the extra item using standard shipping with COD. Our apologies for the confusion and the inconvenience.

I will answer the other question as another FAQ. Please check the Customer Service page to see the answer to that question.

If you have difficulty finding the answer, here is a link:
https://www.buildyourcnc.com/FAQ/13636

Click the link to add information to this solution:
I have a 2000 WK 11–3 Z limit switches going to A c10r10 breakout board . Can I also use them as my home position as well. I need The wiring configuration

Sure, connect O2 (output #2) on your mach3 USB board to the GND side of your relay coil. Connect the 24V power supply to the positive side of your 24v relay.

You will want to connect a flyback diode (1N4007) between the coil connections to make sure the coil back current does not damage the Mach3 USB board.

Refer to this diagram:
https://www.buildyourcnc.com/Documents/Electric%20Wiring%20Diagram.pdf

Please let me know if this helps and if you need further guidance.

Thanks

Click the link to add information to this solution:
I recently purchesed a USB Mach3 breakout board and need help setting mach3 to use a relay to start the router can you show how to set the pins and which port to use on the board to attached the relay?

The instructions on how to do this are found here, in these two videos, http://buildyourcnc.com/PrimeronHomingandLimitSwitches.aspx

Additional Information:

Click the link to add information to this solution:
HOW DO I CONNECT A TOUCH PLATE TO THE BREAKOUT BOARD?

The USB port on the Parallel Interface board is necessary to supply 5V power. Connect with a USB cable to a USB source.

Click the link to add information to this solution:
I purchased a parallel port breakout board. I have checked all the info and found nothing on the usb port. What is it used for?

Most motherboard do contain parallel ports, but the port connector may not be at the back (in the section where external connectors will be connected). Instead, the motherboard may contain an LPT ribbon connector on the actual face of the motherboard (usually along one of the edges). You will need a ribbon connector to a DB25 female connector.

If your motherboard does not contain an LPT header on the motherboard, you can purchase a parallel printer adapter that plugs into one of the PCI slots. The price of the adapter is very inexpensive and sometimes is actually less costly than the actual ribbon connector.

Click the link to add information to this solution:
As I am building my 20" x 24" laser engraver cutter, I notice that there is no parallel port on the onboard computer and I have the parallel breakout board any answers?