No, you should not have received two parallel breakout boards in your CNC kit. You can return the extra item using standard shipping with COD. Our apologies for the confusion and the inconvenience.

I will answer the other question as another FAQ. Please check the Customer Service page to see the answer to that question.

If you have difficulty finding the answer, here is a link:
https://www.buildyourcnc.com/FAQ/13636

Click the link to add information to this solution:
I HAVE A 2000 WK 11–3 Z LIMIT SWITCHES GOING TO C10R10 BREAKOUT BOARD . CAN ALSO USE THEM AS MY HOME POSITION WELL. NEED THE WIRING CONFIGURATION

Are you trying to determine how to wire the switches or where to place them on the Vertical Laser XL? Let me know and I will provide some pictures or video on how to do this.

Additional Information:
Kind of both. Have somewhat of an idea as to how to wire them but you included rotary and other limit switches. Not sure which ones to put where. Never worked with these before.

Click the link to add information to this solution:
Do you have a more detailed diagram of the rotary and 15A limit switches on the vlxl?

If your computer does not have a parallel port, all you will need is a low cost PCI parallel adapter card (these can be found on amazon for $15-$20). If you plan on using a laptop (not recommended) you can try to find a PCMCIA parallel adapter, but many people have frequent issues with this setup. A more expensive solution would be to purchase a USB smooth stepper board. Unfortunately, we do not supply any of these adapters and cannot attest to their reliability.

Additional Information:
ur gay

Additional Information:

Click the link to add information to this solution:
MY COMPUTER DOES NOT HAVE A PARALLEL PORT. HOW DO I INTERFACE WITH THE BREAKOUT BOARD?

No, you should not have received two parallel breakout boards in your CNC kit. You can return the extra item using standard shipping with COD. Our apologies for the confusion and the inconvenience.

I will answer the other question as another FAQ. Please check the Customer Service page to see the answer to that question.

If you have difficulty finding the answer, here is a link:
https://www.buildyourcnc.com/FAQ/13636

Click the link to add information to this solution:
I have a 2000 WK 11–3 Z limit switches going to A c10r10 breakout board . Can I also use them as my home position as well. I need The wiring configuration

We are currently getting it completed for us to post it under the 2.5A stepper driver page. However here is the correct wiring procedure.

First: Wire the 24V power supply to the 2.5A driver, by wiring +V on the power supply to 12-24V on the driver. Next wire the COM on the power supply to Ground(GND) on the 2.5A driver. GND on the driver will also go to the GND on the USB board, for specific axis. (additional 3-4 wires connected to ground will be needed for the other axes as well).

Second: Wire the USB board to the driver(one driver per axis on the USB board):
CP on the driver will go to CP on the desired axis on the USB board.
CW on the driver will go to CW on the desired axis on the USB board.
5V will go to the VCC pin on the keyboard jog pins on the USB board (check schematic here: https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout#prettyPhoto/2/).
GND on the USB board to GND on the driver. (as specified in step 1).
EN is not used.

Personal Note:
I would recommend that you crimp the VCC pin to a wire which could be split for the other axes as well, each driver will need 5V.

Third: Wire the stepper motor to the driver, (using either the Nema 23 100-oz or the Nema 17 62-oz stepper motors, the wiring will be the same. For the Nema 23 the yellow and white is not connected.)
Black to A1
Green to A2
Red to B1
Blue to B2

Fourth: Repeat steps 1-3 for each driver/motor per axis.

Mention: Remember that GND on the driver will also go to the GND on the USB board for specific axis, and VCC pin on the USB board (keyboard jog) will go to 5V on all drivers for each axes as well, each driver will need 5V!

Click the link to add information to this solution:
Is there a complete wiring diagram for the Medium Combo Kit with the usb board? Your USB tutorial does not cover the modular 2.5a drivers. https://buildyourcnc.com/item/electronicsAndMotors-3axis-100-elcombo

If you want speed control, it is recommended to use the RS-485 connection on the VFD and use the control program such as Mach3 to communication serially with the VFD using this RS-485 connection.

If you would rather use a controller such as the PMDX-107 to simulate the effect of a potentiometer using the Aref, Aout and Agnd and the Rev/Dir and Fwd/Run terminals to control operation and direction, you can connect those to the VFD.

PMDX-107 Aout connects to the VI (analog voltage in). This is like the wiper on a potentiometer.
PMDX-107 Agnd connects to the ACM terminal on the VFD for Analog common.
PMDX-107 COM connects to DCM terminal on the VFD for Digital common.
PMDX-107 Fwd/Run connects to the FOR terminal on the VFD for Forward.
PMDX-107 Rev/Dir connects to the REV terminal on the VFD for Reverse.

Refer to your PMDX-107 manual to correctly configure your dip switch settings and make sure to calibrate (tweak) the speed control using the trimmer next to the terminals on the PMDX-107.

Click the link to add information to this solution:
I have the USB controller board and the 8825 step driver. I need a wiring diagram between the two. Specifically, what does the GND pin on the X-axis connect to? Also, what does the 5V pin on the driver connect to?

You can find a wiring diagram here:
https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout#prettyPhoto/2/

The CP terminal is wired to the step terminal on the 8825 step driver.
The CW terminal is wired to the direction terminal on the 8825 step driver.
The GND terminal connects to the GND on the 8825 step driver

The 5V connector on the driver simply powers the logic side of the chip and needs to connect to VCC pin on the keyboard jog.

Customer Response:
Thanks! Working now.

Click the link to add information to this solution:
I have the USB controller board and the 8825 step driver. I need a wiring diagram between the two. Specifically, what does the GND pin on the X-axis connect to? Also, what does the 5V pin on the driver connect to?

I have very detailed wiring videos for the Pokeys57CNC controller on the pokeys57CNC controller webpage: https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Click the link to add information to this solution:
[50] I purchased 3 Axis Heavy Gantry Electronics /w Pokeys57CNC controller (Mach3 and 4 Compatible) and Cable Pack I plan to use Mach 3 do You have a wiring diagram Thanks

Yes, the 5 axis breakout board is a very suitable replacement and also contains a relay for spindle/router control which is not on the C10 board.

Click the link to add information to this solution:
I have propably blown my C10 breakout board. This is no longer available in your parts list. Is the 5 Axis Breakout Board with Relay a suitable replacement?

The instructions to connect the USB CNC Interface for the blackTooth Laser Cutter and engraver can be found on instruction #18 on thispage: https://www.buildyourcnc.com/blackToothLaserCutterAndEngraver.aspx

Click the link to add information to this solution:
Are there any instructions for use the USP breakout board for a CO2 laser?

The 5V power required for the breakout board can be a simple USB male to male cable, that will connect from your computer to the board itself.
Now adding a external power supply make sure that it does not exceed a total of 5V and the standard 500 MilliAMP - 1 A.

Click the link to add information to this solution:
I have a YDH-18-5 Power Supply AC Input:100-240v 47-63Hz, Ouput: 5v - 2A and need to know if its safe to use with the Parallel Breakout Board.

The best wiring diagram that can be used for the redLeaf and redSprout CNC computer system would be found on instruction #1 (datasheet for the breakout board) on this page: https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

Click the link to add information to this solution:
Hi I live in South Africa and want to know if i can buy a wiring and component diagram for the readleaf plug and play computer system?

The best wiring diagram that can be used for the redLeaf and redSprout CNC computer system would be found on instruction #1 (datasheet for the breakout board) on this page: https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

Click the link to add information to this solution:
Hi I live in South Africa and want to know if i can buy a wiring and component diagram for the readleaf plug and play computer system?

The parallel (printer cable) port is uses the computer as its main source of pulse trains to operate the motor driver directly. Parallel ports are a direct connection from the processor commonly referred to as GPIO pins (General Purpose I/O pins) and provides a convenient and powerful way to interface with the computer. The parallel breakout board is included in those kits only to condition those signals for use with the drivers.

The USB serves at the actual controller, sending the pulse trains, but the computer sends simple human readable instructions to the USB controller to tell the controller how to send pulses.

The non-technical differences that may serve as the most important information to you is that the parallel configurations allow for a wider variety of industry standard software that can be used to control the cnc machine. The USB that we offer requires the operator to use a software called Planet-CNC software which is a very well made and feature full cnc control software.

Additional Information:


Additional Information:


Additional Information:
USB Motion controller breakout board work with planet cnc software?

Click the link to add information to this solution:
WHAT'S THE DIFFERENCE BETWEEN PARALLEL BREAKOUT BOARD AND USB ITERFACE?

The parallel is the most versatile breakout board we have and will work with most of the software out there, but many computers are not equipped with parallel connectors anymore. Parallel adapter cards are available if you don't have a parallel connection on your computer.

The USB interface must be used only with the planet-cnc software, which is great software, but you are still limited to only that software application. This is actually the least expensive option unless you use linux and go with the above option.

Click the link to add information to this solution:
WHATISTHE DIFFERENCE WTIH THE PARALLEL BREAKOUT BOARD AND USB BOARD?

The USB port located on the parallel 5 axis breakout board is for powering the board. There is no communications related to this port.

Click the link to add information to this solution:
What is the usb port for on the 5 Axis Breakout Board with Relay ($28.50)?

The wire that we sell for the limit switch wiring is here: https://www.buildyourcnc.com/item/3d-printer-component-cnc-electronicsandmotors-cable-wire-3-conductor-22-awg-wrcon-cablewire3conductor22awg

This is shielded cable to make sure there isn't any external interference with sensitive components and long wires associated with limit switches. This is necessary due to the interference caused by the motors on a CNC router and the milling process.

Additional Information:
So unshielded is cool. That's what I was curious about. Cheers.

Additional Information:
Absolutely. It's really the only type of cable I would recommend for connecting limit switches.

Click the link to add information to this solution:
Do you sell 22 to 24 AWG stranded and shielded for wiring of the limit switches and E_Stop?

The instructions on how to do this are found here, in these two videos, http://buildyourcnc.com/PrimeronHomingandLimitSwitches.aspx

Additional Information:

Click the link to add information to this solution:
HOW DO I CONNECT A TOUCH PLATE TO THE BREAKOUT BOARD?

We don't have cad models of the HIWIN blocks, but you can find the models on McMaster.com. They have can drawings and models for most of these types of parts.

Click the link to add information to this solution:
DO YOU HAVE CAD AVAILABLE FOR THE HIWIN GUIDE BLOCKS SELL AND RAIL?