The gantry sides, gantry bridge parts, two 1/2" rods, two 1/2" ID bearings, two 1/2" ID 12 tooth sprockets, and extra roller chain.

Click the link to add information to this solution:
WHAT IS INCLUDED IN THE BLACK TOE TO FOOT UPGRADE?

PC with parallel port and USB port
20awg stranded wires for the motors - http://www.buildyourcnc.com/electronicscombo.aspx
18awg stranded wires for power supply to drivers
24awg stranded wires for breakout board to drivers
(location and spacing of components varies from one person to another, so we do not provide cables/wires)
- General purpose extension cord (cut the female end off) to provide power to power supply
- USB cable to power breakout board
- Parallel cable to communicate to breakout board
- Router
- (optional - instead of router) Spindle with power inverter http://www.buildyourcnc.com/SpindlesAndAccessories.aspx
- (if purchasing spindle with inverter) General purpose extension cord (240v) (cut the female end off) to provide power to power inverter
- End Mill(s) http://www.buildyourcnc.com/ProductsEndMills.aspx
- CAD, and/or CAD-CAM software (to produce geometry, machine operations, and g-code) http://www.buildyourcnc.com/CNCsoftware.aspx
- CNC control software (to read g-code and control machine) http://www.buildyourcnc.com/CNCsoftware.aspx
- If the machine does not have the table included, then a table will need to be built. The rails, chain and chain mounts are included that are used on this table.

Additional Information:

Click the link to add information to this solution:
WHAT NOT INCLUDED WITH THE MACHINE?

The base greenLean CNC Machine Kit package includes:
- Structure (all of the structural parts that make up the gantry and rib system). The structure does not include the spoilboard.
- Hardware (All of the fasteners, like screws, nuts, cross dowels, washers, etc.)
- Mechanical components (bearings, rails, sprockets, shafts, etc.)
- Electronics (3 NEMA 651 Motors, 3 6.0 Amp drivers power supply, interface card to connect the drivers to a computer, and 91 feet of motor cable. Hookup wire to connect the electronics is not included.)
- 2.2kw Spindle and VFD

Here is a link to the greenLean CNC Macnine page: https://www.buildyourcnc.com/item/cnc-machine-greenLean-v1

Click the link to add information to this solution:
WHAT COMES IN THE BOX FOR BASIC GREENLEAN?

The blackTooth Laser cutter and Engraver can be built in a weekend. Take a look at the build instructions and try to determine if you feel you have sufficient capability to put together the laser system.

Click the link to add information to this solution:
HOW COMPLEX IS YOUR KIT TO ASSEMBLE, AND MOST IMPORTANTLY - HARD IT SETUP CONTROL THE LASER WITH MACH3?

If you are looking for the drivers to pair with NEMA 34 stepper motors, you can find the 6.0 amp drivers here:
https://www.buildyourcnc.com/item/electronicsAndMotors-stepper-driver-6!0a

The other electronics to send the signals to the 6.0 amp drivers (the control board that operates with the control software) is subject to personal preference, but here they are listed:

Our breakout board (works with Mach3 and LinuxCNC and requires a parallel port on your computer):
https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

The PoKeys57CNC (works with Mach3 and Mach4):
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Generic USB breakout board (works with Mach3):
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Additional Information:
Do I need a driver for every motor or can I use one driver for all four motors

Additional Information:
Each motor needs its own driver.

Click the link to add information to this solution:
I HAVE NEMA 34 MOTORS BUT NEED THE ELECTRICAL COMPONENTS DO YOU A KIT WITHOUT INCLUDED?

These machines are inherently dangerous. Before the machine moves, the machine should be clear of any person by a dimension of at the distance of a persons reach plus a few more feet. This is the policies we institute in our shop and what is recommend to all of our customers. Treat these machines as you would treat any major power tool in the shop.

With that said, you can certainly add some protective parts, but still keep folks away even with those installed. I would use the gantry side to do all of the mounting of the protective parts. Consider using sheet metal that you can bend and make a simple installation right on the gantry side.

Additional Information:

Click the link to add information to this solution:
THE CNC MACHINE IS UNSAFE WITH EXPOSED SPROCKETS THAT CAN DAMAGE FINGERS AND HAVE CLOTHING CAUGHT IN IT.

Does your breakout board (interface) have a relay? If so, you can connect one of the router/spindle's ac lines through the relay. The M3, M4 and M5 codes are used to control the router/spindle. Typically, the M codes are automatically added to the g-code regardless if you configure this in your CAM software. If you have the breakout board from buildyourcnc, you can go to the product page for the breakout board and the relay connection diagram and narrative is in the instructions on that page.

Click the link to add information to this solution:
WHAT IS THE MOST EASY WAY TO HOOK UP MILL IN THAT AUTOMATICALLY STARTS WHEN CYCLE STARTS, AND STOPS GCODE THROUGH?

Our CNC machines can be lengthened to work with our customers specific projects.

For a 3.5' x 14' cutting surface, I would recommend our greenBull 4X! (4'x8'). You will only need to add the remaining length of rail(4) and chain(2) to accommodate the additional 6Ft, so this machine will have a cutting surface of 4' x 14'.

The additional lengths for the x-axis travel will be a total of 28Ft, and 14Ft of chain. We recommend selecting all the items you wish to purchase and see the actual total in your cart.

Click the link to add information to this solution:
I HAVE INTEREST IN SOME KIT AROUND 14' X 3.5' CAN YOU SUPPLY? ALREADY PRICE? AND WHAT MORE NEED?, MY IS MODELING KAYAKS CNC

The greenBull 4X comes with all of the components and electronics to assemble the gantry of the machine. You will need to build the table. We provide the rails and roller chain for the X-axis (along the length of the table for full 8 feet of travel). You will need to provide some wire to connect the electronics and a computer to run the machine. You will also need to purchase the software that you will need to run the machine that matches how you will apply the machine. We suggest the mach3 control program. The CAM program is up to you as there are many options out there.

Click the link to add information to this solution:
WHAT DOES THE GREENBULL KIT INCLUDE AND DO I NEED TO INCLUDE?

The parallel (printer cable) port is uses the computer as its main source of pulse trains to operate the motor driver directly. Parallel ports are a direct connection from the processor commonly referred to as GPIO pins (General Purpose I/O pins) and provides a convenient and powerful way to interface with the computer. The parallel breakout board is included in those kits only to condition those signals for use with the drivers.

The USB serves at the actual controller, sending the pulse trains, but the computer sends simple human readable instructions to the USB controller to tell the controller how to send pulses.

The non-technical differences that may serve as the most important information to you is that the parallel configurations allow for a wider variety of industry standard software that can be used to control the cnc machine. The USB that we offer requires the operator to use a software called Planet-CNC software which is a very well made and feature full cnc control software.

Additional Information:


Additional Information:


Additional Information:
USB Motion controller breakout board work with planet cnc software?

Click the link to add information to this solution:
WHAT IS THE DIFFERENCE BETWEEN PARALLEL AND USB ELECTRONICS COMBOS MOTOR KITS

The parallel (printer cable) port is uses the computer as its main source of pulse trains to operate the motor driver directly. Parallel ports are a direct connection from the processor commonly referred to as GPIO pins (General Purpose I/O pins) and provides a convenient and powerful way to interface with the computer. The parallel breakout board is included in those kits only to condition those signals for use with the drivers.

The USB serves at the actual controller, sending the pulse trains, but the computer sends simple human readable instructions to the USB controller to tell the controller how to send pulses.

The non-technical differences that may serve as the most important information to you is that the parallel configurations allow for a wider variety of industry standard software that can be used to control the cnc machine. The USB that we offer requires the operator to use a software called Planet-CNC software which is a very well made and feature full cnc control software.

Additional Information:


Additional Information:


Additional Information:
USB Motion controller breakout board work with planet cnc software?

Click the link to add information to this solution:
WHAT IS THE DIFFERENCE BETWEEN A PRINTER CABLE PORT AND USB MOTOR KITS

The leadscrew length for the greenBull long Z-axis is 47 inches.

Additional Information:

Click the link to add information to this solution:
BUILDING ONE OF YOUR GREENBULL 6X LONG AND 2.2 KILOWATT SPINDLE DOES NOT FIT. SEEMS LEAD SCREW YOU SENT WITH KIT IS SHORT 42" LOOKS LIKE IT NEEDS TO BE 5 OR 6 INCH LONGER. THIS CORRECT? WHAT THE NEEDED LENGTH FOR UNIT?

Depth of Field. This is how far the focal point goes before re-expanding again. With a 2" lens, you have approximately 2-3mm of DOF. This means that you'll have 2-3mm of perfectly focused laser before it starts to re-expand again. If you have a 4" lens, you will have up to 7mm of DOF.

Additional Information:

Click the link to add information to this solution:
WHAT IS D.O.F OR DEPTH OF FIELD FOR THE BLACKTOOTH LASER AND LENS?

Shipping crate size 121" X 36" X 92"

Weight 511 LBS

Click the link to add information to this solution:
WHAT IS SHIPPING DIMENSIONS AND WEIGHT FOR THE VERTICAL LASER.

You can expect a two week lead time for the redFrog pick and place machine.

Additional Information:

Click the link to add information to this solution:
WHAT IS THE LEAD TIME FOR REDFROG PICK AND PLACE MACHINE?

The HIWIN rails come with the same flange blocks that are sold individually.

Click the link to add information to this solution:
About your HIWIN rails. What Carriage block does the 78" rails come with, 2 flange or 2 with no flange?

Standard Version Features Mach3 Mach4 Hobby Mach4 Industrial
Number of Planners 1 1 1
Number of Axis 6 6 6
Out of Band Axis (OBA) 0 1 6
Slave axis (uses up coordinated axes) 3 N/A N/A
Slave motors (does not use up coordinated axes) N/A 4 per Axis 4 per Axis
API Interface - Open to All Hardware Yes Yes Yes
Extended Plugin Support Yes Yes Yes
User customizable GUI Yes Yes Yes
Unified (GUI) Interface - PLC, CNC, etc.. Yes Yes
Unlimited IO Yes Yes Yes
Modbus PLC Yes Yes Yes
PMC (Ladder Logic addressing for cnc/plc) Yes Yes
Unlimited File Size Yes Yes
Tool Path Display Yes Yes Yes
Tool Path Speed & Quality Low High High
Scripting - Customization Yes Yes Yes
LUA Scripting - simple, fast, cross-platform Yes Yes
- Lua sockets (ftp, http, smtp,..) Yes Yes
- SSL (security layer) Yes Yes
- LFS (manage large files and data storage) Yes Yes
- Seriel port Yes Yes
- Enraving of part numbers / serial numbering of parts Yes Yes
- Plugin panel objects Yes Yes
IPC Library for Data Sharing/tracking (Interprocess communication) Yes Yes
Full Feature Screens/Controls Per Machine Type Yes Yes
Currently Availabe: Mill, Router, Lathe, 3d Printer Yes Yes
Multiple gcode Interpruters (Per Machine Type) Yes Yes
Probing - Intergrated in standard screens Yes Yes
Simulated 3d Machining (with additional plugin license) Yes Yes
Tool Life Management (G10 L3 command) Yes
Screw Mapping Yes
Professional Screen Designer (advanced G.U.I.) Yes
- Screen Animation Control Yes
- Screen Integrated Tool Table Control Yes
- Screen Integrated Work Offset Control Yes
- Screen Integrated gcode editor Yes
- Screen Artsoft Wizard Package Integration Yes
Macro B gcode Programming (#variables) Yes
- User definable gcodes via marco calls Yes
- Macro Calls: G65, G66, G66.1 Yes
- gcode via marco call (custom G codes via macro B) Yes
- mcode via macro call (custom M codes via macro B) Yes
- mcode via sub code (custom M code via sup program) Yes
- Conditional gcodes Yes
- set VN call - define variable names Yes
gcode Editor Included Yes
Scripted M code (custom M code via LUA script) Yes Yes
Variable Speed Spindle Yes Yes Yes
Spindle Relay Yes Yes Yes
Coolant relay Yes Yes Yes
Mist Relay Yes Yes Yes
Threading Yes Yes Yes
Rigid Tapping Yes Yes Yes
Single Block Yes Yes Yes
Block Delete Yes Yes Yes
Optional Stop Yes Yes Yes
MACH CNC CONTROL SOFTWARE MAIN FEATURES AND VERSION DIFFERENCES
Standard Version Features Mach3 Mach4 Hobby Mach4 Industrial
MACH CNC CONTROL SOFTWARE MAIN FEATURES AND VERSION DIFFERENCES
Cutter Comp Yes Yes Yes
Fanuc Type C Cutter Comp Yes Yes
Fixture Offsets Yes Yes Yes
G51 Scaling Yes Yes Yes
G92 Offsets Yes Yes Yes
G52 Offsets Yes Yes Yes
Event Driven Yes Yes
Multi Line MDI Yes Yes
Subs In MDI Yes Yes
OpenGL Optimization Yes Yes
Multi-platform OS Compatibility Option Yes Yes
Online Support Yes Yes Yes
Phone Support Option Available Yes
Support Priority Yes
Available to End Users as "Do-it-yourself" Yes Yes
Summary - Mach3 versus Mach4 :
Mach4 Hobby is the closest comparable version to Mach3, yet it is still much more advanced. The price point of these versions is nearly
identical. Mach3 is very popular for hobby enthusiest and is used in highly modified form by some great OEM's. In general, Mach4 is more
complex than Mach3 and follows cnc industry standards. Mach3 has many customizations to make it easier for hobby users, but can lead to
difficulties if users plan to apply their knowledge to more advanced systems. Mach4 is built as a full featured cnc controller capable of high
speed machining for servo and stepper systems. Mach3's feature set is complete, while Mach4's will continue to expand. If you are new to cnc,
Artsoft highly recommends using and learning Mach4 even if it appears that Mach3's feature set will be adequate for your needs.

Click the link to add information to this solution:
WHAT IS THE DIFFERENCE BETWEEN MACH3 AND MACH4?

I don't see anything in the datasheet for the relay that indicates an overheat condition. While the relay is engaged, the power consumption is 400 mW and I don't believe this is enough to raise the temperature faster than the heat dissipation from the metal on the leads through convection or radiation outside of the rated temperature working ranges providing that you maintain an ambient temperature range within -40°C to 85°C (with no icing or condensation).

http://www.omron.com/ecb/products/pdf/en-g2rl.pdf

Click the link to add information to this solution:
IS IT OK TO LEAVE THE VACUUM PRESSURE CONTROLLER PLUGGED IN ALL TIME WHEN PUMP SWITCHED OFF?

You will need to build the table unit for your machine. There are instructions on how to do this at the bottom of the product page here, https://www.buildyourcnc.com/Item/cnc-machine-blackFoot-v4
There is no estimate on how much this will cost though, since there are too many variables involved to do this.

- PC with parallel port and USB port
- 20awg stranded wires for the motors - http://www.buildyourcnc.com/electronicscombo.aspx
- 18awg stranded wires for power supply to drivers
- 24awg stranded wires for breakout board to drivers
(location and spacing of components varies from one person to another, so we do not provide cables/wires)
- General purpose extension cord (cut the female end off) to provide power to power supply
- USB cable to power breakout board
- Parallel cable to communicate to breakout board
- Router
- (optional - instead of router) Spindle with power inverter http://www.buildyourcnc.com/SpindlesAndAccessories.aspx
- (if purchasing spindle with inverter) General purpose extension cord (240v) (cut the female end off) to provide power to power inverter
- End Mill(s) http://www.buildyourcnc.com/ProductsEndMills.aspx
- CAD, and/or CAD-CAM software (to produce geometry, machine operations, and g-code) http://www.buildyourcnc.com/CNCsoftware.aspx
- CNC control software (to read g-code and control machine) http://www.buildyourcnc.com/CNCsoftware.aspx

This answer is applicable to most of our machines with the exception of the greenLean and the blueChick since those machines are equipped with a table structure.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
IF I PURCHASE A GREENBULL 6X LONG Z CNC MACHINE KIT AND MACH3, WHAT ELSE WOULD BE REQUIRED TO ASSEMBLE THE WORKING MACHINE? HAVE CAD SOFTWARE.