[ Register ]

### Question #: 3604

Question: What are the overall dimensions for a greenbull 5x10

Current Solution

The overall size (Foot Print(Roughly)) is:
W: 90" x L: 142.5" x H: 35"

Height:
Is from table top to highest point and not from the floor to highest point.(H for the 5X/6X can vary in size due to the height of the table/frame, since it can be adjusted to the specific needs of the customer)).

Respond:

### Other Possible Solutions to this Question

• WHAT ARE THE SHIPPING DIMENSIONS FOR GREENBULL?

76" X 40" X 26"
230 LBS

WHAT ARE THE SHIPPING DIMENSIONS FOR GREENBULL?

• WHAT ARE THE DIMENSIONS FOR GREENBULL TABLE?

Actual table dimension: 4'x8' is 56.078"x 121.50" (the overhang in the illustrations should be 3/4" thick)
To determine the frame dimensions, first consider using the frame height shown of almost 3' (2.86'). The width of the frame should be 4" narrower than the dimension from rail edge to rail edge (6X rail to rail is 80.078"). This will provide a 2" overhang on both sides (4X frame width should be 56.078").
The length of the frame should be 4" shorter than the desired length of the rails to provide a 2" overhang on both ends. The travel length will be 20" shorter than the rail length due to the space occupied by the gantry sides.
Two long pieces of 3/4" material will need to be placed on top of the frame with the 2" overhang on the sides and the end. These long strips of material will receive the rails and the chain mounts on the ends.

https://www.buildyourcnc.com/Item/cnc-machine-greenBull-v4-4X

WHAT ARE THE DIMENSIONS FOR GREENBULL TABLE?

• what are the table dimensions for 4' by 8' heavy duty greenbull?

Actual table dimension: 4'x8' is 56.078"x 121.50" (the overhang in the illustrations should be 3/4" thick)
To determine the frame dimensions, first consider using the frame height shown of almost 3' (2.86'). The width of the frame should be 4" narrower than the dimension from rail edge to rail edge (6X rail to rail is 80.078"). This will provide a 2" overhang on both sides (4X frame width should be 56.078").
The length of the frame should be 4" shorter than the desired length of the rails to provide a 2" overhang on both ends. The travel length will be 20" shorter than the rail length due to the space occupied by the gantry sides.
Two long pieces of 3/4" material will need to be placed on top of the frame with the 2" overhang on the sides and the end. These long strips of material will receive the rails and the chain mounts on the ends.

https://www.buildyourcnc.com/Item/cnc-machine-greenBull-v4-4X

what are the table dimensions for 4' by 8' heavy duty greenbull?

• What are the table dimensions for the greenBull so I can build it.

Actual table dimension: 4'x8' is 56.078"x 121.50" (the overhang in the illustrations should be 3/4" thick)
To determine the frame dimensions, first consider using the frame height shown of almost 3' (2.86'). The width of the frame should be 4" narrower than the dimension from rail edge to rail edge (6X rail to rail is 80.078"). This will provide a 2" overhang on both sides (4X frame width should be 56.078").
The length of the frame should be 4" shorter than the desired length of the rails to provide a 2" overhang on both ends. The travel length will be 20" shorter than the rail length due to the space occupied by the gantry sides.
Two long pieces of 3/4" material will need to be placed on top of the frame with the 2" overhang on the sides and the end. These long strips of material will receive the rails and the chain mounts on the ends.

https://www.buildyourcnc.com/Item/cnc-machine-greenBull-v4-4X

What are the table dimensions for the greenBull so I can build it.

• What are the overall dimensions of the black toe 2x4?

The overall foot print of the blackToe 2' x 4', from farthest point to point are:
Gantry only (kit):
W: 37"-1/2"
L: 18"
H: 35"

Gantry (kit) with the optional table (add-on):
W: 37"-1/2"
L: 36"
H: 60"

What are the overall dimensions of the black toe 2x4?

• What are the overall dimensions of the GreenLean Machine?

The overall dimensions of the GreenLean Machine are approximately 86 inches Tall by 116 inches wide.

What are the overall dimensions of the GreenLean Machine?

• What are the overall dimensions of the USB interface board? Is there a CAD model available?

The dimensions for our USB breakout board are:

L: 2.745"/ 69.723mm
W: 2.244"/ 56.9976mm
H: .501"/ 12.7254mm

Currently we do not have a CAD model on hand.

What are the overall dimensions of the USB interface board? Is there a CAD model available?

• What are the overall dimensions of the 2.5A small stepper drivers? Is there a CAD model available?

The overall dimensions of our 2.5 modular stepper divers is:

L: 1.875"/ 47.625mm
W: 1.433"/ 36.3982mm
H: .585"/ 14.859mm (height might change due to different terminal block height (other we have on hand is .464"/ 11.7856mm))

Currently we do not have a CAD model on hand.

What are the overall dimensions of the 2.5A small stepper drivers? Is there a CAD model available?

• WHAT ARE THE SHIPPING DIMENSIONS FOR VERTICAL LASER

Shipping crate size 121" X 36" X 92"

Weight 511 LBS

WHAT ARE THE SHIPPING DIMENSIONS FOR VERTICAL LASER

• table dimensions for large format 4' by 8' greenbull?

Actual table dimension: 4'x8' is 56.078"x 121.50" (the overhang in the illustrations should be 3/4" thick)
To determine the frame dimensions, first consider using the frame height shown of almost 3' (2.86'). The width of the frame should be 4" narrower than the dimension from rail edge to rail edge (6X rail to rail is 80.078"). This will provide a 2" overhang on both sides (4X frame width should be 56.078").
The length of the frame should be 4" shorter than the desired length of the rails to provide a 2" overhang on both ends. The travel length will be 20" shorter than the rail length due to the space occupied by the gantry sides.
Two long pieces of 3/4" material will need to be placed on top of the frame with the 2" overhang on the sides and the end. These long strips of material will receive the rails and the chain mounts on the ends.

https://www.buildyourcnc.com/Item/cnc-machine-greenBull-v4-4X

table dimensions for large format 4' by 8' greenbull?

• What are the technical details/dimensions for the 20mm Linear Guide Rail?

For our Hiwin rail, you can find the specifications at this URL:
https://www.buildyourcnc.com/item/mechanical-rails-HIWIN-Linear-20mm-Guide-Rail

For our standard round linear rail, you can find the specifications at this URL:
https://www.buildyourcnc.com/item/mechanical-rails-linear-guide-rails-20mm

What are the technical details/dimensions for the 20mm Linear Guide Rail?

• The plans/hardware option for the greenBull includes what?

The plans/hardware/electronics/mechanical includes everything but the wood structural components that can be cut by the customer. This plans/hardware option includes all of the electronics, like motors, drivers, controller, and all of the cables and wires to connect all of the electronics together. The mechanical components include shafts, couplings, linear rails, bearing blocks, sprockets, lead screws, etc. The hardware consists of all of the screws nuts, insert nuts, cross dowels, etc, to assemble all of the structural, mechanical, and electronics together.

The plans/hardware option for the greenBull includes what?

• what are the dimensions of the pillow blocks for the round linear guide rails?

Are you referring to this part?: https://www.buildyourcnc.com/item/mechanical-rails-linear-ball-bearing-block

yes that block

I created a drawing of the linear bearing guide block that shows the dimensions that you need for mounting. Specifically, the mounting spacing is 1.38 inches both axially and transversely.

You can see the drawing on the linear bearing guide block page here: https://www.buildyourcnc.com/item/mechanical-rails-linear-ball-bearing-block

And directly here: https://www.buildyourcnc.com/images/20mm%20bearing%20guid%20block%20for%20round%20rail-800.JPG

If you need further information, please let me know. Thanks.

what are the dimensions of the pillow blocks for the round linear guide rails?

• what are the motor setting for the greenbull

In the customer service live, just enter "motor tuning" and it will give you a list of all the recommended or default settings for our machines. However the acceleration and velocity for the greenBull(other machines) will be an actual determination on your trials. You will want the highest possible acceleration and velocity without the motors stalling, so you can do increments of ten to be on the safe side, if it is too slow try increments of 25.

The steps per inch is dependent on the microstepping:
Steps/Inch for the x and y
Steps = 200 motor steps per revolution x 16 microsteps = 3200 steps
Inches = sprocket number of teeth x pitch of the sprocket = 14 x .25" = 3.5 inches
steps/inch = 3200 / 3.5 = 914.28
This is really a starting point. You will then need to use the mach3 calibration function to get the perfect steps/inch value. Use as long a measurement as possible when calibrating.

Velocity:
Start with a value of 1000 ipm. Increase this value with a relatively low acceleration at about 10. You will notice at a particular velocity that it will stall. This is your stall velocity. I would take the stall velocity and reduce it by about 30% to 50% which should give you a good final safe velocity.

Acceleration:
Once the velocity is found, raise the acceleration until it start to stall at a low velocity. Reduce the acceleration by about the same percentage to stick with a safe acceleration.

The acceleration is mostly dependent on torque (current) and the top speed is dependent on the amount of voltage.

Give some tests with all of the axes running at the same time. If you notice and stalling, reduce velocities and acceleration depending on when the stall happens (top end, or acceleration curve).

X-axis
“CW8060 (6.0A) Driver”
Set to 5.43A, 1/16 Microstep
Dipswitches: 01100110 (“0”=down, “1”=up)
Mach3 Motor Tuning: 914.29 steps/in
Y-axis
“CW8060 (6.0A) Driver”
Set to 5.43A, 1/16 Microstep
Dipswitches: 01100110
Mach3 Motor Tuning: 914.29 steps/in
Z-axis
“CW8060 (6.0A) Driver”
Set to 5.43A, 1/4 Microstep
Dipswitches: 01100100
Mach3 Motor Tuning: 1600 steps/in

4th axis

what are the motor setting for the greenbull

• table dimensions and clearance for 4' x 8' greenbull (torsion box)?

For the 6'x12' greenBull table dimensions, the table width for the greenBull table must be 80.078" (6.67' or 203.398 cm) and must overhang the underside structure by 1-1/2" to make room for the rails and this overhang portion should be 3/4" thick. The length can be variable, but remember that the gantry takes up some of that space, so add about 34 inches to make room of the gantry and the connecting hardware for the roller chain on the four corners. We recommend if you want a full 12 feet of travel, the table must be at least 178 inches.

table dimensions and clearance for 4' x 8' greenbull (torsion box)?

• What are the specifications for the 2" strip brush as far as dimensions and width of the rubber top?

The strip brush is .2 inches (5.23 mm) wide, so a slot of that width or slightly wider will work. We use a .25 inch groove and use glue to adhere the strip brushes in our dust shoe.

The material of the bristles and the strip that holds the bristles are nylon.

What are the specifications for the 2" strip brush as far as dimensions and width of the rubber top?

• Do you sell plans (dimensions of parts, or even g-code) for me to build a greenbull?

The files and hardware option for our machines has been removed from the site due to the following reasons:
Difficulty for the end use of the files and the challenges (and time/money) on our side to assist in using these files.
The abuse of these files over the internet.
Ultimately may reduce the sales of machines keeping us in business.
Sadly, this is what has come out of our company attempting to be open; however, the machines sold on this site is still far lower in price than the competition for the quality that we provide as we have a great desire to engender the cottage industry to fulfill their need for low end manufacturing. My sincere apologies if this causes any inconvenience.

NO, is not possible, I can help with the shipping cost

Do you sell plans (dimensions of parts, or even g-code) for me to build a greenbull?

• What are the bolt dimensions for the SBR20 linear rails, can they work with 8020 Aluminum extrusions?

Our SBR20 rails use M8 bolts and are suitable for use with 8020 aluminum or any other common machine material. We suggest the use of our ball bearing pillow blocks with these rails, which you can find on our website here: https://buildyourcnc.com/item/mechanical-rails-linear-ball-bearing-block

HOW TO FIND WIDH 38 HEIGHT 26 LINER GUIDE RAIL

What are the bolt dimensions for the SBR20 linear rails, can they work with 8020 Aluminum extrusions?

• What are the dimensions of the 24v 8.3A power supply?

The dimensions for our power supplies will be the same.

Dimensions:
L: 8.5" / 215.9mm
W: 4.5" / 114.3mm
H: 2" / 50.8mm

What are the dimensions of the 24v 8.3A power supply?

Get Help with:
This Product
Orders
Tech Support
Sales
This Product
Order Query
Tech Support
Sales