PC with parallel port and USB port
20awg stranded wires for the motors - http://www.buildyourcnc.com/electronicscombo.aspx
18awg stranded wires for power supply to drivers
24awg stranded wires for breakout board to drivers
(location and spacing of components varies from one person to another, so we do not provide cables/wires)
- General purpose extension cord (cut the female end off) to provide power to power supply
- USB cable to power breakout board
- Parallel cable to communicate to breakout board
- Router
- (optional - instead of router) Spindle with power inverter http://www.buildyourcnc.com/SpindlesAndAccessories.aspx
- (if purchasing spindle with inverter) General purpose extension cord (240v) (cut the female end off) to provide power to power inverter
- End Mill(s) http://www.buildyourcnc.com/ProductsEndMills.aspx
- CAD, and/or CAD-CAM software (to produce geometry, machine operations, and g-code) http://www.buildyourcnc.com/CNCsoftware.aspx
- CNC control software (to read g-code and control machine) http://www.buildyourcnc.com/CNCsoftware.aspx
- If the machine does not have the table included, then a table will need to be built. The rails, chain and chain mounts are included that are used on this table.

Additional Information:

Click the link to add information to this solution:
WHAT NOT INCLUDED WITH THE MACHINE?

If your computer does not have a parallel port, all you will need is a low cost PCI parallel adapter card (these can be found on amazon for $15-$20). If you plan on using a laptop (not recommended) you can try to find a PCMCIA parallel adapter, but many people have frequent issues with this setup. A more expensive solution would be to purchase a USB smooth stepper board. Unfortunately, we do not supply any of these adapters and cannot attest to their reliability.

Additional Information:
ur gay

Additional Information:

Click the link to add information to this solution:
MY COMPUTER DOES NOT HAVE A PARALLEL PORT. HOW DO I INTERFACE WITH THE MACHINE?

In Mach3, go to the Settings Tab, and select "Set Steps Per Unit". It will ask you how far to move the machine. Before you do this, make a mark on the table exactly where the end mill is resting. You can do this by lowering the end mill until it touches the material, then spinning it by hand to cut a small dimple in the material. Then, raise the end mill to clear the material, and assign a distance to move the machine. Once the machine moves and stops, measure the exact distance that it actually traveled with a tape measure, and enter this value into the dialog box that asks how far it moved. Mach3 will automatically adjust your steps per unit for that axis to be more accurate. Do this for all axes often to ensure you are cutting accurately. The longer distances you use calibrate, and the more precise you are with your measurements, the better.

Click the link to add information to this solution:
HOW DO I CALIBRATE MY MACHINE?

I use a standard large "L" square used in construction. I run gantry up and down with the bit along one side of the square to make the square aligned with the x-axis. I then run the bit along the other edge and if I see space from the edge of the bit to the square, I adjust the gantry square by loosening and tightening the eye bolts that hold the chain at the ends of the table. Repeat as necessary to get the desired square.

Additional Information:

Click the link to add information to this solution:
HOW DO I MAKE MY MACHINE SQUARE?

In Mach3, go to the Settings Tab, and select "Set Steps Per Unit". It will ask you how far to move the machine. Before you do this, make a mark on the table exactly where the end mill is resting. You can do this by lowering the end mill until it touches the material, then spinning it by hand to cut a small dimple in the material. Then, raise the end mill to clear the material, and assign a distance to move the machine. Once the machine moves and stops, measure the exact distance that it actually traveled with a tape measure, and enter this value into the dialog box that asks how far it moved. Mach3 will automatically adjust your steps per unit for that axis to be more accurate. Do this for all axes often to ensure you are cutting accurately. The longer distances you use calibrate, and the more precise you are with your measurements, the better.

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:
idwmHJym

Additional Information:
-1 OR 2+78-78-1=0+0+0+1 --

Additional Information:
-1 OR 2+135-135-1=0+0+0+1

Additional Information:
-1' OR 2+886-886-1=0+0+0+1 --

Additional Information:
-1' OR 2+357-357-1=0+0+0+1 or 'xkLzGxAb'='

Additional Information:
-1" OR 2+279-279-1=0+0+0+1 --

Additional Information:
1'"

Additional Information:
1����%2527%2522

Additional Information:
@@5fZce

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
MY MACHINE CUTTING THE WRONG SIZE PART

I use a standard large "L" square used in construction. I run gantry up and down with the bit along one side of the square to make the square aligned with the x-axis. I then run the bit along the other edge and if I see space from the edge of the bit to the square, I adjust the gantry square by loosening and tightening the eye bolts that hold the chain at the ends of the table. Repeat as necessary to get the desired square.

Additional Information:

Click the link to add information to this solution:
HOW DO I SQUARE MY CNC MACHINE OR GANTRY?

The length of time it will take to build a CNC machine kit is not an easy answer. There may be a wide array of circumstances that limit a persons abilities to build the cnc machine kit in an efficient timeframe; however, if you have moderate dexterity and moderately mechanically inclined, you should have no problem building one of our machines within one weekend if the project has very little downtime.

Additional Information:

Click the link to add information to this solution:
HOW LONG WOULD IT TAKE FOR MY TO BUILD A MACHINE?

Yes, the customer will need to sign our NDA (Non Disclosure Agreement) form and send it back to us. We will then send the dxf of the specific updated part of the machine.

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:
UoZD5KPp

Additional Information:
-1 OR 2+416-416-1=0+0+0+1 --

Additional Information:
-1 OR 2+291-291-1=0+0+0+1

Additional Information:
-1' OR 2+657-657-1=0+0+0+1 --

Additional Information:
-1' OR 2+849-849-1=0+0+0+1 or 'WBwHf8k5'='

Additional Information:
-1" OR 2+276-276-1=0+0+0+1 --

Additional Information:
1'"

Additional Information:
1����%2527%2522

Additional Information:
@@z69Jq

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
CAN I GET DXF FILES FOR THE UPDATED PARTS OF MY MACHINE?

A CNC machine is basically a computer controlled high precision tool that is able to make intricate movements accurately and repeatedly. Our machines use common routers and spindles to mill, cut, engrave and shape materials in automated machining operations.

Click the link to add information to this solution:
WHAT IS CNC MACHINE?

The parts list is located on this page: http://buildyourcnc.com/cnckitintro.aspx at the bottom of the description.

Additional Information:



Additional Information:

Click the link to add information to this solution:
PARTS LIST FOR THE BOOK MACHINE

There are almost no limits to the kind of materials you can machine. Anything from wood or plastic to exotic materials like stainless steel can be cut as long as the part can be safely and firmly held and the proper cutting tool and cutting speed are used

Click the link to add information to this solution:
WHAT KIND OF MATERIALS CAN MACHINE?

If your computer does not have a parallel port, all you will need is a low cost PCI parallel adapter card (these can be found on amazon for $15-$20). If you plan on using a laptop (not recommended) you can try to find a PCMCIA parallel adapter, but many people have frequent issues with this setup. A more expensive solution would be to purchase a USB smooth stepper board. Unfortunately, we do not supply any of these adapters and cannot attest to their reliability.

Additional Information:
ur gay

Additional Information:

Click the link to add information to this solution:
IF MY COMPUTER DOESN'T HAVE A PARALLEL PORT, HOW DO I RUN THE MACHINE?

PC with parallel port and USB port
20awg stranded wires for the motors - http://www.buildyourcnc.com/electronicscombo.aspx
18awg stranded wires for power supply to drivers
24awg stranded wires for breakout board to drivers
(location and spacing of components varies from one person to another, so we do not provide cables/wires)
- General purpose extension cord (cut the female end off) to provide power to power supply
- USB cable to power breakout board
- Parallel cable to communicate to breakout board
- Router
- (optional - instead of router) Spindle with power inverter http://www.buildyourcnc.com/SpindlesAndAccessories.aspx
- (if purchasing spindle with inverter) General purpose extension cord (240v) (cut the female end off) to provide power to power inverter
- End Mill(s) http://www.buildyourcnc.com/ProductsEndMills.aspx
- CAD, and/or CAD-CAM software (to produce geometry, machine operations, and g-code) http://www.buildyourcnc.com/CNCsoftware.aspx
- CNC control software (to read g-code and control machine) http://www.buildyourcnc.com/CNCsoftware.aspx
- If the machine does not have the table included, then a table will need to be built. The rails, chain and chain mounts are included that are used on this table.

Additional Information:

Click the link to add information to this solution:
WHAT ELSE DO I NEED WITH THE MACHINE?

The cutting tool is an end mill (it looks like a drill bit). It is a cutting tool that can plunge and cut sideways. That item is not included and is a consumable. You will purchase these very frequently and will have geometry that is very specific to how you apply the cnc machine.

Additional Information:

Click the link to add information to this solution:
IS DRILL BIT USED IN THE CNC MACHINE?

Yes, it is ok if the thickness is plus or minus +/- about 2mm.

Additional Information:



Additional Information:

Click the link to add information to this solution:
THICKER MATERIAL OK TO BUILD THE MACHINE?

the package sizes will be listed in your shopping cart, in the item detail. The site will also fully calculate shipping charges directly from the carrier, for each package you purchase.

Additional Information:

Click the link to add information to this solution:
AND WHAT SIZES ARE THE PACKAGES OF MACHINE.

An axis is a direction of motion controlled by the CNC machine control. It can be linear (motion along a straight line) or circular (a rotary motion). The number of axes a machine has determines it's machining capabilities. A 2.5 axis machine really has three moving axes, but only two axes can move together (most machines sold today are full three axis machines). For machining centers, a three axis machine will have three linear axes. A four or five axis machine will have three linear axes as well as one or two rotary axes.

Note that 2.5 versus 3 axis has yet another context. 2.5 axis machining requires that the machine have three axes, but only two axes must be moving simultaneously at any one time. (Simple operations, like drilling and most milling, fall into this category). On the other hand 3-axis machining requires that all three axes be moving at the same time (More complex operations, like the machining of sculptured surfaces required in molds and airfoils, fall into this category.)

Additional Information:


Additional Information:

Click the link to add information to this solution:
WHAT IS THE DIFFERENCE IN A 2.5 AXIS MACHINE?

Same issue here -- TTL output from the AWC708C never seems to be pulled low. Still troubleshooting.

Click the link to add information to this solution:
MY LASER MACHINE VERTICAL DOES NOT ACTIVATE THE LASER TUBE, VERIFY THE POWER SUPPLIES AND THEY ARE WORKING WHICH THE PROBLEM CAN BE

You can determine if the country is serviceable by:
- selecting the items you want to purchase on the website
- go to the cart (shopping cart top left of any webpage)
- log in, or register
- Enter the address and click on calculate shipping.

The webpage will return the direct rates and whether your area is serviced or not. Feel free to enter any address as long as you are able to receive the package from that address.

The shipping times are determined by the service you select in the shopping cart. If a machine is purchased, we generally have a one week lead time unless otherwise stated in the description of the machine's product page.

Additional Information:

Click the link to add information to this solution:
WHAT IS THE SHIPPING COST OF MACHINE TO AUSTRALIA?