Yes, we can sell that size of fan replacement. Can you provide the type of power supply that you purchased?

Additional Information:
APS02HT86-320-36

Click the link to add information to this solution:
The cooling fan on my power supply has quit. Can I purchase just the replacement fan?

This video will illustrate how to test for laser power:

Click the link to add information to this solution:
HOW TO KNOW IF THE POWER SUPPLY OF THE LASER TUBE IS DAMAGED

All you need is a CNC controller like the following options:

https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

This controller is easy to connect using standard wire screw terminals and works with the mach3 control software.

https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

This controller is a little bit more difficult to connect, but is a more feature-rich controller and will work with both mach3 and mach4 CNC control software titles.

Specifically, a CNC controller connects to the computer via a USB cable and connects to the motor drivers. These controllers also connect to the limit switches, spindle/router control, air/fluid/mist control, etc.

Click the link to add information to this solution:
Can you sell me a kit to control my motor from the pc? I already have a motor, driver and power supply.

There is a th or tl on the laser power supply that serves as the trigger on a high or low signal. There is also a potentiometer "in" terminal that will accept a variable signal from 0v to 5v to control intensity. You can use either of these features to fire the laser tube.

If you have gotten grbl to work, then, no doubtedly, you have the expertise to know the output features of grbl. If grbl allows a pwm output, you can tie this to the potentiometer terminal on the power supply. Otherwise, you will need to use a digital output to control the power supply using th or tl.

Additional Information:


Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
How to wire the Laser Power Supply with an arduino & GRBL ? (I'm not using a blacktooth laser cutter)

Most of our power supplies allow for a 9 amp current draw.

For the Neutral, Live and earth ground, wire gauge for that level of current is 14 for relatively short cable lengths. Increase the gauge for longer lengths past 25 feet.

For the DC 24V output terminals to the drivers, 20 gauge is fine. If the power supply is connecting to only one driver, increase the wire gauge to 14.

Additional Information:
What gage wire should I use from motor to driver

Additional Information:


Additional Information:

Click the link to add information to this solution:
What wire AWG can I use to connect the power supply 24v 8.3 amps

The Mach3 USB interface card uses 5V (powered from the computer's USB) and a 24v to power the inputs, outputs and spindle control

the mach3 usb interface can be found here:

https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

But the mach3 usb does not absolutely need the 24V supply. The 24v supply is only needed if you will be using limit switches (I1-4), VFD controlled automatically and for use with the outputs (O1-4)


Additional Information:
The 36v 8.8 amp power supply we typically recommend is for powering the stepper motor drivers.

Click the link to add information to this solution:
Can I power the Mach3 USB interface 24V with a 48V power supply?

We can supply all of the laser components, but you will need to determine how to mount the components.

Additional Information:
Alternatively, you can purchase our greenBull machine that has the laser/spindle combo head. You can see the laser/spindle head here: https://www.buildyourcnc.com/item/cnc-machine-laser-spindle-combo-head

Click the link to add information to this solution:
Can you supply a "KIT" to convert my 4060Z CNC to a Laser Cutter? What is the difference capabilities between the 40Watt and 80Watt?

We can supply all of the laser components, but you will need to determine how to mount the components.

Additional Information:
Alternatively, you can purchase our greenBull machine that has the laser/spindle combo head. You can see the laser/spindle head here: https://www.buildyourcnc.com/item/cnc-machine-laser-spindle-combo-head

Click the link to add information to this solution:
Can you supply a "KIT" to convert my 4060Z CNC to a Laser Cutter? What is the difference capabilities between the 40Watt and 80Watt?

If you would like to add a laser to a plasma table, you will need the following parts:

Laser tube at 40 watts:
https://www.buildyourcnc.com/item/Laser-Component-Laser-Tube-CO2-40Watt

Mirror mounts (this will depend on the way you mount the laser tube):
https://www.buildyourcnc.com/item/Laser-Component-Mirror-Mount-20mm

Mirrors for the mirror mounts:
https://www.buildyourcnc.com/Item/Laser-component-20mm-mirror-25mm

Laser Tube Power Supply:
https://www.buildyourcnc.com/item/Laser-Component-Power-Supply-CO2-40W

Laser Focus Lens:
https://www.buildyourcnc.com/item/laser-component-20mm-lens-2-inch-50!80mm

Mirror and Lens Mount and Nozzle:
https://www.buildyourcnc.com/item/Laser-Component-Nozzle-20mm-lens-mirror

High Tension Extension Cable:
https://www.buildyourcnc.com/item/Laser-component-Power-Supply-High-Tension-extension-wire

Laser Control System:
https://www.buildyourcnc.com/item/Laser-Component-Laser-Control-System

Screw Posts (to connect the high tension and return wire to the laser tube, highly recommended as the leads on the laser tube are fragile):
https://www.buildyourcnc.com/item/laser-component-newbiehack-connectors-screw-terminal-binding-post

Safety Eyewear for CO2 laser wavelength:
https://www.buildyourcnc.com/item/laser-components-goggles-safety-tinted

Click the link to add information to this solution:
I have an Eagle Plasma table and I want to add a 40 laser. Can you supply me a list of what I need to make this happen.

Upgrade your mirrors to SI coated mirrors, using a HQ ZnSe lens and even pushing up to a beam expander will all boost power. The ideal order of experimenation for lowest cost would be changing out for a higher quality lens labeled HQ ZnSE lens. Next would be SI mirrors, which will absorb less heat and reflect better, the last would be to use a beam expander which expands the beam, reducing the heat signature on the mirrors and makes a tighter focal width.

Click the link to add information to this solution:
CAN BOOST THE POWER OF MY BLACKTOOTH LASER?

For our parallel breakout board (https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay#prettyPhoto/2/) the schematic will show the connections going from the BB to the drivers. The parallel breakout board uses the 25 pin parallel connection to communicate from the computer to drivers, and the USB is used to power the main-board itself, supplying 5V.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
I am wiring my breakout board and it has a USB port on it. Is the USB port there to supply the 5 volt power to it?

Adding more fans will require more power from the power supply. Each fan should have the amps that the fan draws. Add the total amps from the three fans and add one amp for the pump and you will have the total power requirement. The 12V 2amp power supply that accompanies the spindle cooling kit will probably be insufficient for the additional two fans.

Click the link to add information to this solution:
[772] Can I add 3 fans and a bigger radiator to this with the 12vdc power supply

The plans or DXF files are not offered. We sell the machines as kits or fully assembled. The kits are very well priced and will most likely cost less if materials and labor than working from plans (this comes from feedback from many customers that built similar machines from plans).

Click the link to add information to this solution:
co you sell plans so I can cut my own laser setup??

Temperature probe monitor. Very valuable. This keeps you up to date on your coolant temperature levels.

Voltage meter. This will tell you the exact level of voltage/power you are running telling the laser to run at instead of an arbitrary mark on a drawn wheel around your POT.

Ammeter sensitive to 1mA. This will be sure your not over driving your tube and reducing it's life significantly.

Hour meter. This will tell you exactly how long your system has been 'on' giving you a more accurate bead on the length of your tubes life.

Exhaust fan upgrade. The current fan included is 100CFM. You can buy 120mm fans that push 250CFM and I have included a guide on how to go about doing this here. http://buildyourtools.com/phpBB3/viewto ... 8cdd1802bf

To push the exhaust fan even further, if you have the room/power, I would highly recommend investing in a 600+ CFM "Dust Collector" system. 250CFM is still not suffice to draw all the smoke that can come off of 3mm or 1/8 MDF cutting job.

A cutting surface. I bought myself a aluminum 'egg crate' mesh from my local HVAC company. They are used a cover for fluorescent lights and work great for low impact cutting surface. They come in 4'x8' sheets and are easily cut to fit. The other side is if you can find a steel honeycomb cutting bed to fit. These can be quite costly or fairly affordable depending where you are looking. The benefit of a steel honeycomb is you can use high power magnets to hold material down.

Click the link to add information to this solution:
HOW CAN YOU ENHANCE THE BLACKTOOTH LASER CUTTER?

You can control our 40W laser power supply (which controls the laser tube) with an Arduino, if that is your intention. The trigger for turning the laser on and off uses a 5V level. To control intensity, you can use the Arduino PWM output. If you want the Arduino to move the machine as well (providing pulse trains to each of the stepper motor drivers) then you will need to make sure you consider the processing speed of the Arduino so you will be able to run the stepper motors at the speed you need for the laser engraving/cutting.

Our laser controller do all of these functions. Here is a link to our laser control system:
https://www.buildyourcnc.com/item/Laser-Component-Laser-Control-System



Additional Information:
Thank you! I am building a 3 axis cnc/ engraver and I think this would be a good option as well as the router head and the 3d printing head. How heavy is the tube? I may mount it directly onto one of the axis of the machine to eliminate the need to line up all three axis, similar to what you have with your xl engraver.

Additional Information:
The tube isn't that heavy, but when filled with water, it can get up to a few pounds. The key is to use the axis moving the nozzle for engraving as this requires fast back and forth motion. The cutting is generally dependent on the axes moving from vector to vector at a relatively slow motion, so this is not a problem.

Click the link to add information to this solution:
I would like to build a low cost laser engraver/ cutter, can your 40w laser power supply be controlled with an arduino or is it only controlled by the controller sold here?

All you need is a CNC controller like the following options:

https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

This controller is easy to connect using standard wire screw terminals and works with the mach3 control software.

https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

This controller is a little bit more difficult to connect, but is a more feature-rich controller and will work with both mach3 and mach4 CNC control software titles.

Specifically, a CNC controller connects to the computer via a USB cable and connects to the motor drivers. These controllers also connect to the limit switches, spindle/router control, air/fluid/mist control, etc.

Click the link to add information to this solution:
Hello there, I am a beginner in trying to control a stepper with a pc, you can sell me a kit to control my motor from the pc. I already have a motor, driver, and power supply

Any of the following power supplies will be fine for powering the Mach3 USB controller:
https://www.buildyourcnc.com/item/24v

however, the limit switches do not need high current, so the following power supply is sufficient for the task of connecting limit switches:
https://www.buildyourcnc.com/item/electronicsAndMotors-power-supply-24v-1a-dc

Click the link to add information to this solution:
What power supply do you recommend for the spindle and limit switches if I buy the USB Mach3 breakout board?

Absolutely, I can answer this type of question and anything other questions you may have with your new-to-you CNC router.

Additional Information:
20

Click the link to add information to this solution:
[789] Can you help me with selecting a power supply ( and a few other components ) for the stepper motors that came with a homemade CNC Router I just purchased.

CO2 laser will not cut wood material fast at all. This is just the nature of the laser energy. The wood is a very low absorbent of the laser energy and you will need to run probably around 10 ipm to cut through the wood. CNC is much more efficient for cutting and laser as more efficient at marking or slowly cutting if you need the small kerf. You will also need a relatively high output air source to cut efficiently. The air will blow away the char (carbon) on the wood. The black char will absorb most of the laser energy not allowing the wood to be cut well. We use a compressor for the air source, but you can use a commercial hydroponic air pump instead.

Click the link to add information to this solution:
How fast can I cut 1/4" wood with the 40 watt CO2 laser?