U - Pin1
V - Pin2
W - Pin3
Pin4 Dead

Additional Information:
My home made cnc is a big problem with my NC connection. When in start my spindle it will be gone wrong. It will be limith switch problem anytime. Need help thanks.

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
WHAT ARE THE OUTPUT INVERTER (VFD) CONNECTIONS TO SPINDLE?

BYCNC response:

Milling aluminum is no problem with our machines.

Here is a video we recently did with our 4'x8' machine. The aluminum piece is about 1/4" thick: https://buildyourcnc.com/tutorials/tutorial-greenbull-aluminum-cutting

The accuracy you will see from our our 2.2kW spindle is entirely dependent on the precision of your build, so it's not possible to say what level of accuracy you can achieve without an examination of the complete system. However, our spindles have a runout of less than .0001 in, which includes the collets that we sell. If you use a collet from another manufacturer, we cannot guarantee this TIR (Total Indicated Runout) dimension.

For the dimension drawing of the anti-backlash nut, please contact us directly by phone or email to techsupport@buildyourcnc.com

User response:
I have emailed waiting for your reply.

User response:
Hi, I am still waiting for your email reply.

BYCNC response:
Your email has been sent.

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
HI, I HAVE INTENTION OF PURCHASING YOUR 1/2 INCH PRECISION LEAD SCREW SET TO BUILD MY CNC MACHINE, COULD THE SCHEMATIC DIMENSION ANTI-BACKLASH NUT, BEARING FOR AND SHIM? ALSO IS 2.2KW SPINDLE ABLE MILL ALUMINUM WHAT ACCURACY?

BYCNC response:

Milling aluminum is no problem with our machines.

Here is a video we recently did with our 4'x8' machine. The aluminum piece is about 1/4" thick: https://buildyourcnc.com/tutorials/tutorial-greenbull-aluminum-cutting

The accuracy you will see from our our 2.2kW spindle is entirely dependent on the precision of your build, so it's not possible to say what level of accuracy you can achieve without an examination of the complete system. However, our spindles have a runout of less than .0001 in, which includes the collets that we sell. If you use a collet from another manufacturer, we cannot guarantee this TIR (Total Indicated Runout) dimension.

For the dimension drawing of the anti-backlash nut, please contact us directly by phone or email to techsupport@buildyourcnc.com

User response:
I have emailed waiting for your reply.

User response:
Hi, I am still waiting for your email reply.

BYCNC response:
Your email has been sent.

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
HI, I HAVE INTENTION OF PURCHASING YOUR 1/2 INCH PRECISION LEAD SCREW SET TO BUILD MY CNC MACHINE, COULD THE SCHEMATIC DIMENSION ANTI-BACKLASH NUT, BEARING FOR AND SHIM? ALSO IS 2.2KW SPINDLE ABLE MILL ALUMINUM WHAT ACCURACY?

VFD settings........
1) To program the VFD, wire it up, plug it in. It takes several seconds to come to life.

2) Push the PRGM button to enter programing mode.

3 )Push the SET button. The display will read PD000.

4) If you push the SET button again, it will display the present setting of PD000.

5 )By pushing the up or down arrows, you can change the setting to whatever it needs to be. (This is just an example. PD000 needs no changes)

6)Push the SET button again to lock in the setting of PD000 and advance to the next number, in this case, PD001.

7) Push the SET button and it will display the present setting of PD001. Again, use the up and down arrows as necessary to set PD001, then push SET again to lock it in.

Note: You can also scroll through the PD numbers with the up and down arrows.

8) make all settings this way.

9) by pushing the SET button you can scroll through the settings. First push of SET moves to the next number, second push displays it's setting, third push moves to the next PD number.

Note- If you take too long, it will leave the programing mode on it's own. If it does, just push PRGM again to return to programing mode. Then press SET and continue what you were doing.

10) Start with PD013. Set it to 1, which returns the settings to the factory settings.

11) Then set PD005 to 400, PD004 to 400, and PD003 to 400 IN THAT ORDER.

12) Then set the following: PD041=8, PD144=3000

13) Set PD209=50

That's it for the programing. You should get 24000RPM when you push RUN.

Click the link to add information to this solution:
I JUST RECEIVED A REPLACEMENT SPINDLE (2.2KW 220V). HOWEVER, WHEN ATTEMPTED IT USE THE NEW SPINDLE, WOULD ONLY REACH 1500 RPM. IS THERE SOMETHING NEED TO CHANGE ON CONTROLLER?

Input to VFD:
240V Active - R
240V Neutral - S
Ground - E

Additional Information:

Click the link to add information to this solution:
WHAT ARE THE SPINDLE INVERTERS (VFD) INPUT AC CONNECTIONS FROM WALL OUTLET?

It is not necessary to connect the spindle VFD (Variable Frequency Drive also called an Inverter) to the computer or CNC motion electronics. The VFD can be controlled independently using the control panel on the VFD. The control panel has the ability to control all aspects of the spindle including Speed, Torque, limits, etc. However, you can connect the VFD to the computer so the CNC control program can control the spindle during the CNC Machine operation. You will need to connect the VFD to the computer via a serial conection (in this case, it is the RS-485 protocol).

The following are instructions on how to connect the VFD to Mach3 via this RS-485 serial connection.

The first thing you will need is the dynamic link library to pair with mach3 called the Huanyang VFD Mach3 PlugIn. You can find this file at the mach3 support forum here: http://www.machsupport.com/forum/index.php/topic,14182.0.html

You will also need to download the Microsoft .net 3.5 framework and install it: https://www.microsoft.com/en-us/download/details.aspx?id=21

Follow the pdf that comes with the library file, but here is a synopsis of what you need to do (I also added a lot more information that may be useful during this process as the manual does not cover the main connections that need to be done):

You will need to program your VFD so that it knows how to communicate with mach3 and the computer (go into the programming mode of the VFD and change these parameters):
- PD001 - value 2 - Enables with communication aspect of the VFD
- PD002 - value 2 - Enables frequency control from the communcations port
- PD163 - value 1 - VFD address
- PD164 - value 1 - Baud rate of 9600 (speed of the communication)
- PD165 - value 3 - 8N1 RTU - 8 bits (that's the size of the word that gets communicated), N (No parity or no error checking) and 1 (1 stop bit)

Copy the dll file to the PlugIns folder of mach3.

Connect the RX and TX lines to your computer. There are a couple ways you can do this, but the recommended way would be to use an FTDI USB device which converts a USB to a serial com port. The device will have Rx and Tx connectors to connect to the VFD terminals with the same labels. This method is recommended since serial ports are not as common in computers these days.

Next, you will need to configure mach3 to use the plugin library. Start mach3 and click on Menu -> config ->Config Plugins. Enable the new plugin by clicking on the red cross on the left column next to the plug in. Restart mach3 after doing this.

No you need to configure mach3 to use the HuanyangVFD plugin. Go to the ports & pins configuration and select the spindle setup tab. Make sure that the Disable Spindle Relays checkbox is unchecked. We don't want mach3 to output a signal for a relay since the spindle will start up and turn off within the VFD and not from an external relay.

Next, go to the HuanyangVFD settings by clicking on Menu -> plugin control -> HuanyangVFD. Set the parameters to the same settings you put into the VFD programming. The com port will be shown as new hardward when you plug in the USB FTDI device. A little bubble will be displayed at the bottom right where it will notify you that a new device is being installed (be patient while windows assigns a com port). Alternatively, you can use the windows device manager to see which port was set for the new USB FTDI device). You may need to restart mach3 several times until you get the correct information displayed in the PD001 and PD002 fields. When the com port is correct and the other parameters, like baud and VFD address is the same as you entered in the programming, then the PD001 and PD002 will show the number 2, otherwise, a 99 will appear which means that communication was not successful.

You can now control the on/off and RPM of the spindle using the RS485 communication between mach3 and the VFD.

Additional Information:
The question was how to connect the spindle to the redfy. I did not receive a VFD.
I have the redFly system and a 2.2kW Spindle - 110V how do i connect the spindle?

Additional Information:
If you received a spindle without a VFD, please contact us asap. Our spindle will not work without a VFD.

Additional Information:
Hi, how is this setup in mach4?

Click the link to add information to this solution:
I HAVE THE REDFLY SYSTEM AND A 2.2KW SPINDLE - 110V HOW DO CONNECT SPINDAL?

This will depend on the VFD you have to identify the correct terminal. The terminal on the VFD will be labeled AI1 typically (Analog Input #1). You will also need to make sure to complete the PWM circuit using the GND terminal on the VFD.

Additional Information:
I have wired my 0-10V signal to the AI1 and GND terminals as suggested. I have also set the PD-01 and PD-02 settings to 1. Still nothing. Is there something else that I am missing?

Additional Information:
Thanks for the information. Can you let me know the model of the VFD that you have?

Additional Information:
VFD Model # YL600-2S-2K20

Additional Information:
Thanks. I will check our resources and documentation to see if there is another programming setting that needs to be changed.

Additional Information:
Does your VFD have a VI terminal?

Additional Information:
No, it does not. The terminals for this VFD are as follows (seperated by dashes "-").

10V-AI1-AO2-PLC-DI5-DI3-DI1-COM
AI2-GND-AO1-DI6-DI4-DI2-FM-24V

Additional Information:
Do you have a PD070 parameter?

PD070 is the main Analog Input parameter.

The options for that parameter is:
0: 0-10V
1: 0-5V
2: 0-20mA
3: 4-20mA
4: 0-10V (4-20mA Stacked)
5: XIA
6: (VI+XIA)/2
7: (3VA+XIA)/4
8: (XIA_XIB)/2
9: Max (XIA, XIB)
10: Min (XIA, XIB)


Additional Information:
There is a PD-00 thru PD-09. PD-07 is currently set to 0.

Additional Information:
It appears that the manual I’m using “Titled YL600” is not the same as your unit. I will check our manuals and find the one that has only PD-00 to PD-09.

Additional Information:
For that VFD, the parameters are P0. The 0 may look like a D on the display.

The parameters that need to be changed for the AI1 to work (Brackets [] around the correct selection):

P0-01: First Motor Control Mode
- 0: Sensorless Vector Control
- 1: Flux Vector Control (FVC)
- [2]: V/F Control

P0-02: Options of Command Source
- 0: Operation Panel Command Channel (LED will be off)
- [1]: Terminal Command Channel (LED will be on)
- 2: Communication Command Channel (LED will flicker)

P0-03: Options of Principle Frequency Source X
- 0: Digital Setting (Preset Frequency P0-08, UP/DOWN modifiable, no power-down memory)
- 1: Digital Setting (Preset Frequency P0-08, UP/DOWN modifiable, with power-down memory)
- [2]: AI1
- 3: AI2
- 4: AI3
- 5: Pulse Setting (DI5)
- 6: Multi Speed Instruction
- 7: Simple PLC
- 8: PID (Proportional Integral Derivative Control)
- 9: Communication Given

P0-11: Upper Limit Frequency Source
- 0: P0-12 (Make sure the P0-12 parameter has the correct max frequency if used)
- [1]: AI1
- 2: AI2
- 3: AI3
- 4: Pulse Setting
- 5: Communication Given

P0-27: Command Source Bundle with Frequency Sources
Single Digit: Options of Operation Panel Command Bundle with Frequency Sources
- 0: No Bundling
- 1: Digital Setting Frequency
- [2]: AI1
- 3: AI2
- 4: AI3
- 5: Pulse Setting (DI5)
- 6: Multi Speed Instruction
- 7: Simple PLC
- 8: PID
- 9: Communication Given
Double Digit: Options of Terminal Command Bundle with Frequency Sources
Hundred Place: Options of Communication Command Bundle with Frequency Sources
Kilobit: Options of Automatic Operation Bundle with Frequency Sources

P2-09: Upper Limit Source of Lower Torque Under Speed Control Mode
- 0: Function Code P2-10 Setting
- [1]: AI1
- 2: AI2
- 3: AI3
- 4: Pulse Setting
- 5: Communication Given
- 6: MIN (Al1, Al2)
- 7: MAX (Al1, Al2)
- Maximum range for options 1-7, accords with P2-10

If you elect to use a different AI#, then configure the parameters (P0-03, P0-11, P0-27 and P2-09) accordingly.

Click the link to add information to this solution:
I'VE BUFFERED A PWM SIGNAL TO 0-10V ANALOG AND I WOULD LIKE USE THAT RUN YOUR 110V 2.2KW SPINDLE VFD. COULD YOU PLEASE DETAIL THE CORRECT WIRING VFD SETTINGS GET WORKING?

The 12V power supply has 3 terminals for AC in: N, L and earth ground. The output of the 12V power supply has 2 DC + and - terminals. Cut the connectors off of the ends of the fan and pump wires. Strip the red and black wires of both units. The fan will connect to the 12V power supply red to the + and black to the -. The pump will connect in the same way, but the white is not connected.

If you have a pump that has a grey and black wire on the large connector, the grey is the 12VDC V+ wire and the black wire goes to the V-. The extra wire does not need to be connected.

Click the link to add information to this solution:
THE GANTRY MOUNTED SPINDLE WATER COOLER PUMP THAT I PURCHASED DOES NOT OPERATE NO MATTER HOW CONNECT THREE WIRES TO TWO WIRE POWER SUPPLY.

Yes, all of the spindles come with collets. The collets have a 1/4" (6.35mm) bore for end mills that have a 1/4" shank. The ER specification is different for the 1.5kW (ER-11) and the 2.2kW (ER-20).

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
I’M LOOKING TO PURCHASE SPINDLE AND VFD WAS CURIOS IF THE SPINDLES COME WITH COLLETS SO WHICH ONES?

Cooling is not as tricky as you might think. There is 3 ways to approach this, only 2 really matter for a low scale 40w setup. First one is the cheapest and easiest. The higher the temp of water the worse your performance will be, from what I understand anything in the 30C range is about the most tolerable it gets. Lower is better. But not frozen...from what I've been told a very experienced cutter, he found 8C was the highest power he achieved.

1. Use a 5 Gallon resovoir system which gives you a fairly large space of water to heat up before you need to tend to it. Add about a cup of anti-freeze to the mix of DISTILLED water. You don't want ANY minerals in the water that might build up in your system. The anti-freeze works to keep algae and other ickies from growing in your water.

2. Use a smaller resovoir system (or even closed loop) and install 1 or more radiators found in CPU cooling systems with 120mm fans attached. This will continously cool your water system to ambient room temperatures, but with a tiny resovoir it will be difficult to add things like ice-packs to drop the temps if the ambient is quite hot.

3. Using an industrial coolant system. Overkill and unless your cutting A LOT, this is a very expensive option to take. You can also explore the idea of Peltier cooling but it is extremely expensive electricity/BTU wise compared to an industrial cooler.

Click the link to add information to this solution:
BUT DIDN'T SEE ANYTHING ABOUT COOLING THE LASER OFF - IS YOUR SETUP LIKE MOST OTHERS NEED BUCKET OF DISTILLED WATER TO PUMP THROUGH MACHINE?

What controller are you using to control the cnc machine (Mach3 usb, parallel breakout board, etc.)?

The spindle VFD has an input for 0-10 volts to control the speed and can be used with the MAch3 USB or the Pokeys57CNC board. There are also other terminals in the VFD to control the forwared/reverse and start and stop. Mach3 has parameters to control these output and you need to specify which pins are used for these.

You can also use the TX/RX RS-485 connection on the VFD to have total control using an FTDI USB to serial connector board to connect the computer directly to the VFD.

How to connect the USB to Serial adapter to the VFD:
https://www.buildyourcnc.com/FAQ/13790

FTDI USB to Serial:
https://www.buildyourcnc.com/item/Interfaces-newbiehack-Interfaces-TTL232R-USB-UART-Serial

Pokeys57CNC board:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Mach3 USB board:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Parallel Breakout board:
https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay



Additional Information:
I do apologize for leaving out the parts list.
Leadshine MX4660 4-Axis Digital Stepper Motor Driver
Ethernet SmoothStepper
YL600-2S-2K20 VFD
4 Relay control board
Has anyone had any success getting Mach3 to control the spindle speed and direction?

Click the link to add information to this solution:
I have the 2.2KW VFD. I would like to have it controlled through software. What are the Mode parameters that need to be changed that will allow FWD/ REV, START/STOP and RPM control?

To loosen and tighten the collet nut for the 2.2kW spindle, I use a 22mm wrench (spanner) for the shaft and a 30mm wrench for the nut.

Click the link to add information to this solution:
WHAT SIZE WRENCHES DOES THIS SPINDLE TAKE TO TIGHTEN?

Can you provide the model number of your VFD?

Yes, I have the "YL600 - 2S - 2K20"

It just came with a small booklet that is all in Chinese...

Click the link to add information to this solution:
I WIRED MY VFD (2.2KW VERSION) AND TRIED TEST RUNNING THE SPINDLE. CONFIGURED TO YOUR SPECS ON THIS WEBSITE, ONLY ISSUE IS WE GOT AN ERROR CODE. ERR 02, DO YOU KNOW WHAT IS? OR HAVE A LIST OF CODES? THANK

You will need to look for the parameter that controls the run frequency. The frequency can be controlled bu the panel, external terminals, or the RS485 TX/RX terminals (UART protocol). You will want to change that parameter so it uses the panel. If you are referring to the maximum panel dial frequency is only allowing 200-300 rpm, then look for the parameters to control the frequency.

For 200 RPM:
Hz = 200/60 = 3.33 Hz

For 300 RPM:
Hz = 300/60 = 5 Hz

Conversion to RPM:
If you ever find yourself yearning to reverse-engineer the process, the formula is as follows:

RPM = Hz × 60

Look for values that match somewhere between 3 and 5 in your frequency parameters and replace them with 400 to give you 24,000 RPM max.

Click the link to add information to this solution:
I HAVE A 2.2KW WATER COOLED SPINDLE WITH YL620-H VFD. THE VFD USES P#-## PROGRAM FORMAT. BELIEVE ALL CORRECT SETTINGS SETUP BUT WHEN TURN UNIT ON, IT SPINS AT ABOUT 200-300 RPM REGARDLESS OF WHAT FREQUENCY CHOOSE. DO YOU PARAMETERS IN THIS FORMAT FOR UNIT? THANK YOUR HELP. HUIBERT MEES

The collet in the 1.5 kW spindle is an ER-11 and cannot reach the 1/2" size. I would consider the 2.2 kW spindle instead.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
WHAT SIZE COLLET IS IN YOUR 1.5 KILOWATT SPINDLE?

Does your breakout board (interface) have a relay? If so, you can connect one of the router/spindle's ac lines through the relay. The M3, M4 and M5 codes are used to control the router/spindle. Typically, the M codes are automatically added to the g-code regardless if you configure this in your CAM software. If you have the breakout board from buildyourcnc, you can go to the product page for the breakout board and the relay connection diagram and narrative is in the instructions on that page.

Click the link to add information to this solution:
WHAT IS THE MOST EASY WAY TO HOOK UP MILL IN THAT AUTOMATICALLY STARTS WHEN CYCLE STARTS, AND STOPS GCODE THROUGH?

The lens is 20mm wide and a 50.6mm focal length (the one included). This lens will stand up to at least 30PSI air assist.

The mirrors are 25mm wide mirrors.

Focal length is the distance from the lens to the material for the laser converge into the best focal point. If a lens is listed as 2". You measure 2" from the lens to the material, this will be the tightest point the laser can go before it starts to re-expand again losing focus.

Click the link to add information to this solution:
WHAT ARE THE BLACKTOOTH LENS SIZES AND FOCAL LENGTH SPECIFICATIONS?

The type of wire that should be used between the spindle and the VFD (Variable Frequency Driver also called the inverter) should be of stranded type and we use between 18 and 16 AWG.

The total current is divided among the three coil wires, therefor a wire gauge of 16 should be sufficient.

Currently we use 20AWG 4 conductor.

Additional Information:


Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
WHAT ELECTRICAL CABLE DO I USE TO CONNECT VFD INVERTER SPINDLE?

The total length of the brush strip for a 2.2kW spindle would be 17 1/4" inches.

Additional Information:
20

Click the link to add information to this solution:
LENGTH OF THE BRUSH STRIP FOR SPINDLE 2.2KW