There are written instructions located at each component (product) page. On the page for your interface board, you will see a datasheet that shows the wiring diagram from that board to the drivers, limit switches and computer. On the page for the stepping motor that you have, there is a datasheet that shows the wiring scheme from the motor to the driver and also has the amp rating for configuring the driver.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
Also on the 3 axis combo, the last item on the tutorials page points to wiring instructions and links to videos. The (I assume) written instructions do not load and the videos seem to be unavailable

Polabs prepared step by step user guide for PoKeys57CNC and Mach4 to try answering such questions. It is available in our downloads section: https://www.poscope.com/wp-content/uploads/downloads/Pokeys/LibrariesAndPlugins/Mach4 and PoKeys57CNC - step by step guide.pdf

Click the link to add information to this solution:
I need your assistance... I have two items left to setup on my Pokey57CNC and Mach4, Home switches and Spindle Speed. I have watched the videos, but they are for Mach3 and the screens are different in Mach4. Can someone please explain the setup of these two items in Mach4?

For our parallel breakout board (https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay#prettyPhoto/2/) the schematic will show the connections going from the BB to the drivers. The parallel breakout board uses the 25 pin parallel connection to communicate from the computer to drivers, and the USB is used to power the main-board itself, supplying 5V.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
The electronics package I just bought from you (Book Build) is different from your wireing diagrams and video tutorials. Is there an updated wiring diagram available? Is the USB port on the breakout board connected directly to the computer USB to supply 5 volts? Thank you.

Which machine has the issue with the videos?

Click the link to add information to this solution:
I can't get any of the original build your cnc videos to load past step 5. Can anyone help please?

Are you using the control panel (front panel with the speed control knob known as he potentiometer)? Or are you attempting to use the computer to control the speed?

Additional Information:
I am using the control panel, however there is no knob on mine, just buttons.

Click the link to add information to this solution:
Hello, I bought your 110v 2.2kw spindle and vfd. When I turn it on it reaches the full 24000 rpm, but will not let me decrease the speed. How Can I fix this?

The specifications for our 3/8" bearings are R6ZZ. The ZZ means double metal shielded. The metal shielding is to protect the ball bearings between the inner race and outer race.

Inside diameter: 3/8"
Outside Diameter: 7/8"
Width: 9/32"

Click the link to add information to this solution:
what are the dimensions and model number of the 3/8" ID roller bearings on your website?

You can find the required components for our scratch build CNC here(https://buildyourcnc.com/cnckitintro.aspx).

Lead Screw needed will be:
X-axis: 52 Inches
Y-axis: 32 Inches
Z-axis: 14 Inches

These will be the bearings that are specified that will be needed:
Bearings 1/2" Inside Diameter - 6
Bearings 5/16" Inside Diameter - 24

Click the link to add information to this solution:
Hi, I need the lead screws and bearings for the 4' x-axis, the 2'(?) y-axis and the 1'(?) z-axis as specified in the book 'Build your own cnc'. I am not sure which to order on your website. Thanks

If your motors are hot to the touch, this is normal. Current is being drawn by the motor coils as the motor moves and as the motor stays at a position. If the motor is not using the current in the coils to move (holding it's position), the energy will be translated as heat (rather than motion, sound or light). Even while moving, some of the energy will be lost as heat. Remember that energy cannot be created nor destroyed.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
Are the stepper motors on x and y axis suppose to be hot after running for approximately 30 min. I can touch them but they are hot.

Unfortunately, end mills will dull over time and need to be sharpened or repurchased. We do not currently offer any sharpening service, but we have a large selection of end mills you can find here http://www.buildyourcnc.com/ProductsEndMills.aspx

Click the link to add information to this solution:
Hi, I got two different bits I use alot. The 1/16th and 1/32 end mills. I use them alot for making signs. They seem to be getting dull. They are very expensive so I was wondering can you sharpen these bits? Do you have a service to do this? Thank you

You can find instructions for the Mach3 USB here:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

You will probably need to use the Mach3 USB board with Mach3. We have not tested the Mach3 usb card with Mach4.

Click the link to add information to this solution:
Whereb can I find directions on how to install the Mach3 USB board with Mach 4 software? I do not have a parallell port.

The book pdf documents are on this page:
https://www.buildyourcnc.com/Book.aspx

Just click on the red area in the first paragraph that states: Click here for the book's documents.

Or, you can just go here for the documents directly for your convenience:
https://www.buildyourcnc.com/Documents/CNC%20Kit%201-1.pdf

Additional Information:
The mdf sheets layout are here:
https://www.buildyourcnc.com/Documents/cuts-Layout1.pdf
and here:
https://www.buildyourcnc.com/Documents/cuts-Layout1%20(2).pdf

Click the link to add information to this solution:
in the book page 18 it says the are down loadable pdf files containing the measurements of the mdf sheets I can not find them on your site even under the book tab

Your steps per inch will vary. I suggest watching my calibration video.

Click the link to add information to this solution:
I AM CURRENTLY HAVING SOME PROBLEM SQUARING THE GANTRY AND MY STEPS PER INCH ARE NOT 1422.22 ACCORDING TO YOUR CALCULATIONS IN AUTO SET UP THEY COME OUT LIKE 1416.#### THIS A BIG DEAL?

The 2.2 kW spindle is used in that video since it can receive end mills and tools that have a 1/2" shank.

Click the link to add information to this solution:
In the video on your website where you show the spoilboard cutter in action (http://buildyourcnc.com/Tutorials/tutorial-spoilboard-surfacing) what spindle are you using?

Sure, we can send you a replacement LED indicator. Just send an email to customerservice@buildyourcnc.com, include your address and we will send it poste haste.

Click the link to add information to this solution:
The LED Status indicator on the front of my Blacktooth laser is not working any longer. I'm looking to get a replacement but can't seem to find them on your website. Do you sell replacements? Thank you.

To get the activation code, all you need to do is plug the USB board into the computer using a USB cable, go to machine -> firmware -> update. After the firmware is updated the program will present to you a dialog box containing the activation code.

Additional Information:
MUAR-QVXU-CAYW-CBWQ


Additional Information:
MUIS-RQPB-PTHB-QTTB

Additional Information:
MUIH-EERP-IADB-TRIP

Additional Information:
9zYWBVf5TxKSK7hEr8gFX3EBw5wa0AMMllQqgftIAnKvZ8DXItLxaPbOB3jWvnpczl/sM/De0scRPHfSxWGmcA==

Additional Information:
Key: LUQR-BQYI-SCEW-QVBT

Additional Information:


Additional Information:
after i copy the code in the lower case i recived the same message (more than 8 times) ,, this is a evaluation...,, what i need to do to register properly?

Additional Information:
MUJR-BISM-KRDN-KKER
056971

Additional Information:
0561234

Additional Information:
MURL-QPQU-EGBJ-FNMB

Additional Information:
MUCE-LFMQ-WBCW-MLHO

Additional Information:


Additional Information:
LUTA-ADVJ-FXTW-FBCE

Additional Information:
LUTA-ADVJ-FXTW-FBCE

Additional Information:
looking for registration key for MUUK-IBTW-ECTL-CJWD

Additional Information:
MUXO-PIYY-KNHD-RKLY

Additional Information:
MUUE-YYCR-FCIC-VATK

Additional Information:
MUUE-YYCR-FCIC-VATK

Additional Information:


Additional Information:
MUEY-YLJU-OBRR-LJBV

Additional Information:
MUSP-JFDV-EKGQ-OVLW

Additional Information:
MUSP-JFDV-EKGQ-OVLW

Additional Information:


Additional Information:


Additional Information:
MULY-XRYF-BBDN-FBWP

Additional Information:


Additional Information:


Additional Information:
how to generate activation code richauto a11

Additional Information:
MUJC-LNIL-EOHS-YKNQ

Additional Information:
sdfd

Additional Information:
m l

Additional Information:
MUXC-RWKB-PKAL-HGNN

Additional Information:
57625YY60Y7Y30X5

Additional Information:
57625YY60Y7Y30X5

Additional Information:
57625YY60Y7Y30X5

Additional Information:
57625YY60Y7Y30X5

Click the link to add information to this solution:
THEY ARE ASKING FOR THE ACTIVATION CODE AND SERIAL NUMBER USB BOARD. HOW CAN GET THAT INFORMATION?

There are two things to consider when using two stepping motors on a single axis. Since you want both motors to spin at the same rate and possibly in the same direction, you need to connect both motor drivers to the same breakout board pins. For example, if you want two motors on the x-axis and the x-axis pins on the breakout board are #2 for step and #3 for direction, the #2 will connect to the step (cp) terminal on each driver and the #3 will connect to the dir (cw) terminal on each driver.

However, if the motors will be opposing (one motor will need to spin in the other direction), you will need to consider either flipping the rack on one side, or adding a circuit to invert the direction (#3) signal going to that driver.

Click the link to add information to this solution:
I'm planning a rack and pinion style gantry, and need clarification on how to slave a second stepper to the Y (or X). Can you direct me to that information for your products?

You should have no problem connecting the Pokeys57CNC controller to the drivers of your machine as long as the drivers have step (Pulse or PUL) and direction (DIR) terminals. You will need the cable pack that is sold separately so you can connect the headers/connectors of the pokeys57cnc controller to the drivers using ribbon cables.

I show this process in great detail on this page:
https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Is you scroll down on the page, you will see a set of videos that show the process step-by-step.

Click the link to add information to this solution:
I have a ShopBot CNC that was converted to Mach 3. The controller has gone out. I pourchased your Pokeys57 board, but I'm not sure I have everything I need. I think my motor drivers are OK, but am not sure how to wire them to what I purchased from you. Need Help. How can we make this work, or do I need a different board to distribute the movement signals to my drivers?

If the pdf. files cannot be viewed please update your pdf. reader, also for the X Table End, There are two of these table ends on the machine, each an exact mirror of the other. You will need six (1/4") 2" screws to fasten this to the two table halves. The two holes on either side of the bearing seat require 3" screws to fasten the motor mounts.

For specific requests with needed files (please state email address or email customerservice@buildyourcnc.com)

Click the link to add information to this solution:
I am building the machine frome the book. The measurements for the 6 screws that hold the table together are missing. The chapter seven addisional material on the your website has the measurements but they are unreadable. Can you send me a PDF of that sheet. The cnckit1-1.pdf file on your website also is missing the measurements. Thanks Joe

The whiteAnt is no longer sold; the information on the website is to support legacy customers. We have spoken with you and are sending the materials that you need.

Click the link to add information to this solution:
I am having difficulty with the wiring on the White Ant. The latest electronics that I received don't seem to be anything like the book or even the tutorials. For instance, the three stepper drivers need 6 pin connectors and ribbon cable. How are they wired? There was no thermocouple wire included. Thanks,