Yes, we can create an only wood kit for you. Please give us a call on Monday to provide your name so we can look it up in our system to confirm your previous purchase and we will provide a PayPal invoice for the kit, since this is a special case.

Click the link to add information to this solution:
Is it possible to purchase the wood pieces only for a BlackToe 2.0/2.1? I have all of the hardware from my kit, but the wood pieces were lost in a recent move.

You will need to build the table unit for your machine. There are instructions on how to do this at the bottom of the product page here, https://www.buildyourcnc.com/Item/cnc-machine-blackFoot-v4
There is no estimate on how much this will cost though, since there are too many variables involved to do this.

- PC with parallel port and USB port
- 20awg stranded wires for the motors - http://www.buildyourcnc.com/electronicscombo.aspx
- 18awg stranded wires for power supply to drivers
- 24awg stranded wires for breakout board to drivers
(location and spacing of components varies from one person to another, so we do not provide cables/wires)
- General purpose extension cord (cut the female end off) to provide power to power supply
- USB cable to power breakout board
- Parallel cable to communicate to breakout board
- Router
- (optional - instead of router) Spindle with power inverter http://www.buildyourcnc.com/SpindlesAndAccessories.aspx
- (if purchasing spindle with inverter) General purpose extension cord (240v) (cut the female end off) to provide power to power inverter
- End Mill(s) http://www.buildyourcnc.com/ProductsEndMills.aspx
- CAD, and/or CAD-CAM software (to produce geometry, machine operations, and g-code) http://www.buildyourcnc.com/CNCsoftware.aspx
- CNC control software (to read g-code and control machine) http://www.buildyourcnc.com/CNCsoftware.aspx

This answer is applicable to most of our machines with the exception of the greenLean and the blueChick since those machines are equipped with a table structure.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
IF I PURCHASE A GREENBULL 6X LONG Z CNC MACHINE KIT AND MACH3, WHAT ELSE WOULD BE REQUIRED TO ASSEMBLE THE WORKING MACHINE? HAVE CAD SOFTWARE.

You will need to build the table unit for your machine. There are instructions on how to do this at the bottom of the product page here, https://www.buildyourcnc.com/Item/cnc-machine-blackFoot-v4
There is no estimate on how much this will cost though, since there are too many variables involved to do this.

- PC with parallel port and USB port
- 20awg stranded wires for the motors - http://www.buildyourcnc.com/electronicscombo.aspx
- 18awg stranded wires for power supply to drivers
- 24awg stranded wires for breakout board to drivers
(location and spacing of components varies from one person to another, so we do not provide cables/wires)
- General purpose extension cord (cut the female end off) to provide power to power supply
- USB cable to power breakout board
- Parallel cable to communicate to breakout board
- Router
- (optional - instead of router) Spindle with power inverter http://www.buildyourcnc.com/SpindlesAndAccessories.aspx
- (if purchasing spindle with inverter) General purpose extension cord (240v) (cut the female end off) to provide power to power inverter
- End Mill(s) http://www.buildyourcnc.com/ProductsEndMills.aspx
- CAD, and/or CAD-CAM software (to produce geometry, machine operations, and g-code) http://www.buildyourcnc.com/CNCsoftware.aspx
- CNC control software (to read g-code and control machine) http://www.buildyourcnc.com/CNCsoftware.aspx

This answer is applicable to most of our machines with the exception of the greenLean and the blueChick since those machines are equipped with a table structure.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
If I purchase a greenBull 6X Long Z CNC Machine Kit and Mach3, what else would be required to assemble the working machine? I have CAD software.

Unfortunately we no longer include or sell our CNC plans for none of our machines. We will be here to assist you if any parts wear over time, and will be able to replace the parts if needed.

Charges may be subjected due to time of purchase and cause of wear.

Click the link to add information to this solution:
Can I purchase plans to scratch build the Blackfoot or GreenBull machine

If you are referring to aligning the rails so that the rails are perfectly parallel:

It is important to make sure one rail (a rail at one side of the table) is perfectly aligned first. Do this by fastening one end of the rail to the table (flush with the table edge), then fasten the other end (flush with the table edge). The rail may not be perfectly straight at this point, but that's ok. This process includes the top and bottom rail, fastening and positioning simultaneously.

You are going to fasten the midpoint of the rail. Get a clamp ready so that you can freeze the rail in place. Look down the rail from one end. This is a good way to determine if the rail has a curve, or is straight. If there is a curve, move the rail midpoint laterally until the rail is straight while looking down the rail from one end of the rail. This may take a couple of people to do, one looks down the rail, the other moves it slightly until it is straight and then clamps the rail. Drill and fasten the midpoint when satisfied. Repeat this process, fastening at the midpoint between screws.

Now place the gantry on the table with the v-groove bearings resting on the one rail side. Add the next rail to the other side of the table. Position the rail so that it is directly under the other bearings. Make sure the gantry is at the extreme end and fasten the rail at that end. Move the gantry along the and fasten the rail as you move the gantry so the rail auto-positions itself.

Additional Information:
Thanks for your answer. So the next step is making certain that the gantry is exactly perpendicular to the x axis. Do you just place a square on the rail and adjust one or both chains as needed?

Click the link to add information to this solution:
Is there a specific process for aligning the x axis on the greenbull? There is mention of it at the end either the rail or gantry installation but I could not find it anywhere.

The files and hardware option for our machines has been removed from the site due to the following reasons:
Difficulty for the end use of the files and the challenges (and time/money) on our side to assist in using these files.
The abuse of these files over the internet.
Ultimately may reduce the sales of machines keeping us in business.
Sadly, this is what has come out of our company attempting to be open; however, the machines sold on this site is still far lower in price than the competition for the quality that we provide as we have a great desire to engender the cottage industry to fulfill their need for low end manufacturing. My sincere apologies if this causes any inconvenience.

Additional Information:
NO, is not possible, I can help with the shipping cost

Additional Information:

Click the link to add information to this solution:
I was wondering if it is at possible to get a autocadd drawing of the pieces that need to be built for your cnc hardware kit

If you were logged in when you made the purchase, you can click the "My Account" link at the top of any page on this website and see all of your orders, order line items (with direct links to these items), and shipment information.

Here is a link to the "My Account" page for your convenience:
https://www.buildyourcnc.com/CustomerInfo.aspx

I did not see your username on your internal customer record, so I added this username and you should be able to see the information in the "My Account" page.

Additional Information:
I just tested your accounts page and the cable carrier links are in there. Thanks and please let me know if you need further assistance.

Click the link to add information to this solution:
I have purchased cable carrier chain and would like to know if you could send me a copy of that order as I need to purchase extra lengths of the links I bought. Thanks

I'm not sure I understand the question. You are looking for spacers or sprockets?

Additional Information:
Nevermind, I found my answer. Thank you

Click the link to add information to this solution:
Since you don't sell the hardware only package for the Blackfoot 4'x8' can you tell me what items I should look for for the chain sprockets, spacers to mount them to the 1/2" rod, and chain? All the other parts I can source from elsewhere

You can get them from us. Please send an email to sales@buildyourcnc.com with your order information, or call our customer service line M-F 9-5 at 281-815-7701.

Click the link to add information to this solution:
Working on GreenBull 5x10 assembly and I am missing one 1/2 rigid coupling for installing the X axis motor and chain mounts. I am also missing the two 1/2 drive sprockets as well. Where can I get these items?

Only our greenBull CNC machines will be able to use the long Z-axis, due to structural construction of the greenBull over the blackFoot.
The height from the table top to the bottom of the gantry is: 4.25"

Both the maximum cutting height and diameter, will be dependent on the specific end mill/router bit you plan on using, since they can vary in length.
The maximum cutting height (useful to engrave or cut material)is: with spoil-board 3.875", without a spoil-board is 4.625"
The maximum diameter will (estimated) is: 3"

Specifically dealing with our greenBull long Z-axis CNC machines, depending on how you specifically design the table you can have more cutting height and a larger diameter clearance. If you only create a frame for the machine with a hollow center(adjustable midsection), allowing you to have a greater clearance.
Similar table image here: (https://buildyourcnc.com/Item/cnc-machine-greenBull-v4-6X#prettyPhoto/5/)

Click the link to add information to this solution:
I can't spot the differences between 4'x8' blackFoot and the 4'x8' greenBull (except for laser head option): please, can you tell me?

Only our greenBull CNC machines will be able to use the long Z-axis, due to structural construction of the greenBull over the blackFoot.
The height from the table top to the bottom of the gantry is: 4.25"

Both the maximum cutting height and diameter, will be dependent on the specific end mill/router bit you plan on using, since they can vary in length.
The maximum cutting height (useful to engrave or cut material)is: with spoil-board 3.875", without a spoil-board is 4.625"
The maximum diameter will (estimated) is: 3"

Specifically dealing with our greenBull long Z-axis CNC machines, depending on how you specifically design the table you can have more cutting height and a larger diameter clearance. If you only create a frame for the machine with a hollow center(adjustable midsection), allowing you to have a greater clearance.
Similar table image here: (https://buildyourcnc.com/Item/cnc-machine-greenBull-v4-6X#prettyPhoto/5/)

Click the link to add information to this solution:
Planning to Buy Greenbull or Blackfoot 4'x 8' Long "Z" Axis. My questions are: what is the hight between the table and the Gantry ? what maximun Z can useful engraving? if I instal a rotating 4 Axle. what maximun diameter can be useful.

That is correct. We send the fewer ribs than could be fastened within the gantry. One reduction of a rib will provide more space for the motor at the midpoint of the gantry and at the other side of the gantry (opposite the motor) can be reduced to provide more space to work with the coupling.

Click the link to add information to this solution:
I'm assembling the gantry for a 5x10 greenbull and noticed that there are 9 spaces for torsion spacers but only 7 in the kit. Should I just space them out on the right side behind the motor?

The motors do get conditionally hot, because of the constant current going through the motor. The motors should not overheat and stall/fail they are built in the manner to withstand the constant current and heat. Modifying the machine to something that is considered a safe/personal machine is recommended for all our machines.

Click the link to add information to this solution:
Have there been problems with the Greenbull stepper motors overheating? I'm considering adding a fan with filtered inlet and outlet on the gantry plus heat sinks on X, Y and Z.

Roller chain in general is adjustable by using "master links", which are links which have horseshoe clip holding the pin and thus allow connections to be made or broken. The #25 is a designation of the type of roller chain. ANSI codes designate that the first digit(s) specify the pitch in eights of an inch, and the last digit is 0 for standard chain, 1 for lightweight chain, and 5 for bushed chain with no rollers. So #25 is 2/8 = 1/4 inch pitch bushed chain with no rollers.

Click the link to add information to this solution:
IS THE "#25 ROLLER CHAIN" ADJUSTABLE TO ANY LENGTH? LIKE IF I ORDERED TEN FEET OF IT, CAN MAKE TWO 3-FOOT LOOPS AND ONE 4-FOOT LOOP USING SOME SORT CHAIN JOINER?

You will need to build the table unit for your machine. There are instructions on how to do this at the bottom of the product page here, https://www.buildyourcnc.com/Item/cnc-machine-blackFoot-v4
There is no estimate on how much this will cost though, since there are too many variables involved to do this.

- PC with parallel port and USB port
- 20awg stranded wires for the motors - http://www.buildyourcnc.com/electronicscombo.aspx
- 18awg stranded wires for power supply to drivers
- 24awg stranded wires for breakout board to drivers
(location and spacing of components varies from one person to another, so we do not provide cables/wires)
- General purpose extension cord (cut the female end off) to provide power to power supply
- USB cable to power breakout board
- Parallel cable to communicate to breakout board
- Router
- (optional - instead of router) Spindle with power inverter http://www.buildyourcnc.com/SpindlesAndAccessories.aspx
- (if purchasing spindle with inverter) General purpose extension cord (240v) (cut the female end off) to provide power to power inverter
- End Mill(s) http://www.buildyourcnc.com/ProductsEndMills.aspx
- CAD, and/or CAD-CAM software (to produce geometry, machine operations, and g-code) http://www.buildyourcnc.com/CNCsoftware.aspx
- CNC control software (to read g-code and control machine) http://www.buildyourcnc.com/CNCsoftware.aspx

This answer is applicable to most of our machines with the exception of the greenLean and the blueChick since those machines are equipped with a table structure.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
Can I purchase a computer off Amazon (I have a machine I want to use) and still use the USB interface to drive it with LinuxCNC?

You will need to construct the table frame to your specifications and with a structure, fixtures and clamping to hold the timber that will be sculpted. You will also need the appropriate end mill that is designed to carve the timber. A dust extraction (vacuum) will be necessary to remove the dust and chips.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
Hi, I intend on sculpting a surfboard out of a timber slab using the following kitset: greenBull 6x with Hybrid Laser/Spindle Head (includes Spindle/VFD and Laser Components) - USB Interface (Long Z). Will i need to purchase any additional items to have a fully operational cnc machine that is capable of carving the surfboard from a timber slab?

Roller chain in general is adjustable by using "master links", which are links which have horseshoe clip holding the pin and thus allow connections to be made or broken. The #25 is a designation of the type of roller chain. ANSI codes designate that the first digit(s) specify the pitch in eights of an inch, and the last digit is 0 for standard chain, 1 for lightweight chain, and 5 for bushed chain with no rollers. So #25 is 2/8 = 1/4 inch pitch bushed chain with no rollers.

Click the link to add information to this solution:
Is the "#25 Roller Chain" adjustable to any length? Like if I ordered ten feet of it, can I make two 3-foot loops and one 4-foot loop using some sort of chain joiner?

The electronics (stepper motors, drivers, power supply and interface board) can be found here:
https://www.buildyourcnc.com/item/electronicsAndMotors-3axis-425-elcombo

If your computer cannot connect to the parallel breakout board (the interface card), just make sure to inform us that you need the USB alternative.

Click the link to add information to this solution:
Just purchased the book "Build Your Own CNC Machine". Can I get hardware and electronics kits and how?

See initial question.

Additional Information:
Initial question is: https://www.buildyourcnc.com/FAQ/14009

Click the link to add information to this solution:
Follow up to the last question. I can just make a couple new pieces of acrylic but I just wanted to know if you had any other ideas. Thank you.