[ Log In ]
[ Register ]

Question #: 13680

Question: how do I connect the parallel breakout board?

Current Solution

You can go here to find the diagrams and instruction on connecting the parallel breakout board:

https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

Also, please make sure to watch all of the electronics tutorial videos here:
https://www.buildyourcnc.com/CNCElectronicsandWiring.aspx

Respond:

Other Possible Solutions to this Question

  • Should I connect both the USB and the 25 pin connector of the parallel breakout board to the computer?

    The parallel breakout board has the db25 connector for data and the USB connector for power. Connect the USB from the computer to the parallel breakout board so the breakout board will have 5V of power coming from the computer. The db25 connector (connector with the 25 pins) receive data signals for each pin from 1 to 17 and have respective numbered screw terminals, some for input and some for output (18 to 25 are gnd pins).

    Click the link to add information to this solution:
    Should I connect both the USB and the 25 pin connector of the parallel breakout board to the computer?

  • HOW DO I CONNECT A TOUCH PLATE TO THE BREAKOUT BOARD?

    The instructions on how to do this are found here, in these two videos, http://buildyourcnc.com/PrimeronHomingandLimitSwitches.aspx

    Additional Information:

    Click the link to add information to this solution:
    HOW DO I CONNECT A TOUCH PLATE TO THE BREAKOUT BOARD?

  • MY COMPUTER DOES NOT HAVE A PARALLEL PORT. HOW DO I INTERFACE WITH THE BREAKOUT BOARD?

    If your computer does not have a parallel port, all you will need is a low cost PCI parallel adapter card (these can be found on amazon for $15-$20). If you plan on using a laptop (not recommended) you can try to find a PCMCIA parallel adapter, but many people have frequent issues with this setup. A more expensive solution would be to purchase a USB smooth stepper board. Unfortunately, we do not supply any of these adapters and cannot attest to their reliability.

    Additional Information:
    ur gay

    Additional Information:

    Click the link to add information to this solution:
    MY COMPUTER DOES NOT HAVE A PARALLEL PORT. HOW DO I INTERFACE WITH THE BREAKOUT BOARD?

  • I can't find the diagram to hook up the parallel breakout board

    You can go here to find the diagrams and instruction on connecting the parallel breakout board:

    https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

    Also, please make sure to watch all of the electronics tutorial videos here:
    https://www.buildyourcnc.com/CNCElectronicsandWiring.aspx

    Click the link to add information to this solution:
    I can't find the diagram to hook up the parallel breakout board

  • can I use the usb on the parallel breakout board with planet cmc

    The USB on the Parallel breakout board, is used for powering the board itself (5v USB), and the Parallel to communicate directly between the drivers and the computer/mach 3.
    Planet-CNC cannot be used with our Parallel Breakout Board, it is only intend to be used with Mach 3/other open source programs.

    To use Planet-CNC, please refer to our USB breakout board! (https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout)

    Click the link to add information to this solution:
    can I use the usb on the parallel breakout board with planet cmc

  • Why didn't I receive a ribbon cable so that I could connect the parallel breakout to the motherboard?

    Please email customerservice@buildyourcnc.com so we can assist you.

    Click the link to add information to this solution:
    Why didn't I receive a ribbon cable so that I could connect the parallel breakout to the motherboard?

  • I have your breakout board with relay parallel port , how can I wire up a regular router to that board so I can control the router

    Here is how to connect your router to the parallel breakout board through the on-board relay. You will need a spare extension cord. You will need to remove a portion of the outer jacket of the extension cord to expose the white, black and green wires (white = neutral, black = live and green = ground), understanding that the neutral and live create the completed circuit.

    See this image of a similar connection. The terminal has the same connections.
    https://www.buildyourcnc.com/images/vacuum-pressure-controller-relay-terminals-700.JPG

    Image of the relay terminal:
    https://www.buildyourcnc.com/images/breakoutboardrelayNONC.PNG

    The live/black wire would be cut and one end of the cut would be secured into the P terminal and the other cut end would be secured into the S terminal. The live and ground wire would be uncut and travel from the plug to the router.


    Additional Information:
    You can also connect other high powered devices to the breakout board using any of the output terminals. You will need to supply extra relays like the one shown here:
    https://www.buildyourcnc.com/item/electronicsAndMotors-breakout-Relays-relay-board-250V-12A-5V

    Or you can find SSRs (Solid State Relays) that will accept 5v to drive the relay coil. Make sure the SSR will protect the 5V line from Back EMF as there is a coil in the relay. The one we sell contains a fly-back diode to protect the 5v terminal.

    Click the link to add information to this solution:
    I have your breakout board with relay parallel port , how can I wire up a regular router to that board so I can control the router

  • Hi, I need assistance, the parallel breakout board I received looks different from the one on the video, does this one need a 5V supply? If so, where do I connect the positive and where do I connect the ground? Thanks for your help.

    Hi, this BBB comes with a USB port and its cable to power it up. Once connected to the computer a led in the BBB will light up to show it has power.

    Additional Information:
    Breakout board I have does not have USB port for the 5v power. Does the parallel port supply the 5V power?

    Click the link to add information to this solution:
    Hi, I need assistance, the parallel breakout board I received looks different from the one on the video, does this one need a 5V supply? If so, where do I connect the positive and where do I connect the ground? Thanks for your help.

  • WHATISTHE DIFFERENCE WTIH THE PARALLEL BREAKOUT BOARD AND USB BOARD?

    The parallel is the most versatile breakout board we have and will work with most of the software out there, but many computers are not equipped with parallel connectors anymore. Parallel adapter cards are available if you don't have a parallel connection on your computer.

    The USB interface must be used only with the planet-cnc software, which is great software, but you are still limited to only that software application. This is actually the least expensive option unless you use linux and go with the above option.

    Click the link to add information to this solution:
    WHATISTHE DIFFERENCE WTIH THE PARALLEL BREAKOUT BOARD AND USB BOARD?

  • WHAT'S THE DIFFERENCE BETWEEN PARALLEL BREAKOUT BOARD AND USB ITERFACE?

    The parallel (printer cable) port is uses the computer as its main source of pulse trains to operate the motor driver directly. Parallel ports are a direct connection from the processor commonly referred to as GPIO pins (General Purpose I/O pins) and provides a convenient and powerful way to interface with the computer. The parallel breakout board is included in those kits only to condition those signals for use with the drivers.

    The USB serves at the actual controller, sending the pulse trains, but the computer sends simple human readable instructions to the USB controller to tell the controller how to send pulses.

    The non-technical differences that may serve as the most important information to you is that the parallel configurations allow for a wider variety of industry standard software that can be used to control the cnc machine. The USB that we offer requires the operator to use a software called Planet-CNC software which is a very well made and feature full cnc control software.

    Additional Information:


    Additional Information:


    Additional Information:
    USB Motion controller breakout board work with planet cnc software?

    Click the link to add information to this solution:
    WHAT'S THE DIFFERENCE BETWEEN PARALLEL BREAKOUT BOARD AND USB ITERFACE?

  • HOW DO I WIRE FROM THE BREAKOUT BOARD TO DRIVER?

    CP+ to COM
    CP- to STEP
    CP+ to CW+ (small jumper wire)
    CW- to DIR

    Additional Information:
    If the driver does not have CP or CW labels, the CP is Step and the CW is Direction or DIR. If you connect the 5v to CP+ (or Step+) and CW+ (or DIR+) and the pin to CP- (or Step-) and another pin to CW- (or DIR-), then in software, the configuration for the step on that axis must be active low. Otherwise, if you connect the GND to CP- (or Step-) and CW- (or DIR-) and the pin to CP+ (or Step+) and another pin to CW+ (or DIR+), then in software, the configuration for the step on that axis must be active high.

    Additional Information:
    If you have a driver that is labeled pul, dir and ena: Pul+ is the Step+ and Pul- is the Step-. Pul is short for pulse. A pulse will create a step. Don't worry about the enable terminals.

    On the x-axis, pin #2 can go to pul- and pin #3 can go to dir-. The 5v will go to pul+ and dir+. The configuration for each axis for step will be active low and toggle active low for the dir on each axis to make it go in the direction desired.

    Additional Information:


    Additional Information:


    Additional Information:


    Additional Information:

    Click the link to add information to this solution:
    HOW DO I WIRE FROM THE BREAKOUT BOARD TO DRIVER?

  • I have a parallel. breakout board. and no parallel port at the back of my computer do those parallel. cards. work with the breakout board?

    If your computer does not have a parallel port, all you will need is a low cost PCI parallel adapter card (these can be found on amazon for $15-$20). If you plan on using a laptop (not recommended) you can try to find a PCMCIA parallel adapter, but many people have frequent issues with this setup. A more expensive solution would be to purchase a USB smooth stepper board. Unfortunately, we do not supply any of these adapters and cannot attest to their reliability.

    Additional Information:
    ur gay

    Additional Information:

    Click the link to add information to this solution:
    I have a parallel. breakout board. and no parallel port at the back of my computer do those parallel. cards. work with the breakout board?

  • Is there a mapping on the input (switch) pins to an axis on the parallel breakout board?

    The mapping of the input pins of the parallel breakout board is configured through software. The input pin are very versatile and can be mapped to all kinds of different types of input including axis limits and axis homing.

    Click the link to add information to this solution:
    Is there a mapping on the input (switch) pins to an axis on the parallel breakout board?

  • I can't find any information in the BlackTooth instructions about how to connect the 8 wires from the LED display to the parallel breakout board. The two going to the pot seem, in the illustration, to be soldered together and to the centre terminal of the pot? Help, please.

    To connect the parallel port breakout board to the LEDs, use step number 18. The connections are listed at the bottom. Here it is for your convenience.

    For the LED connections on the parallel breakout board:

    - The x axis LED will be connected to pin #2 and 5V
    - The y axis LED will be connected to pin #4 and 5V
    - The laser on/off LED is connected to pin #6 and 5V

    Click the link to add information to this solution:
    I can't find any information in the BlackTooth instructions about how to connect the 8 wires from the LED display to the parallel breakout board. The two going to the pot seem, in the illustration, to be soldered together and to the centre terminal of the pot? Help, please.

  • I have a 3 axis combo w/ parallel breakout board. Will this work with Mach 4?

    Our electronics kits with the parallel breakout board will work with Mach 4, however you will need to purchase the Legacy Driver for Mach 4 to work with our breakout board.

    Click the link to add information to this solution:
    I have a 3 axis combo w/ parallel breakout board. Will this work with Mach 4?

  • I purchased a parallel port breakout board. I have checked all the info and found nothing on the usb port. What is it used for?

    The USB port on the Parallel Interface board is necessary to supply 5V power. Connect with a USB cable to a USB source.

    Click the link to add information to this solution:
    I purchased a parallel port breakout board. I have checked all the info and found nothing on the usb port. What is it used for?

  • I have a YDH-18-5 Power Supply AC Input:100-240v 47-63Hz, Ouput: 5v - 2A and need to know if its safe to use with the Parallel Breakout Board.

    The 5V power required for the breakout board can be a simple USB male to male cable, that will connect from your computer to the board itself.
    Now adding a external power supply make sure that it does not exceed a total of 5V and the standard 500 MilliAMP - 1 A.

    Click the link to add information to this solution:
    I have a YDH-18-5 Power Supply AC Input:100-240v 47-63Hz, Ouput: 5v - 2A and need to know if its safe to use with the Parallel Breakout Board.

  • Installing THC to my limit ports on the breakout board. Once wired how do I get Mach 3 to reconize the port?

    Getting continuity from the x--/x++ might not mean it is a faulty board, unless they are bridged, so both get a pulse rather than one. But to check if you might have a opposite connection for those input:
    Planet-cnc/file/settings/input/invert inputs/input 1/input 2.

    Additional Information:
    In input port section in config. Scroll down and you will see THC On, Up and Down. Enter your input pin numbers there.

    Click the link to add information to this solution:
    Installing THC to my limit ports on the breakout board. Once wired how do I get Mach 3 to reconize the port?

  • As I am building my 20" x 24" laser engraver cutter, I notice that there is no parallel port on the onboard computer and I have the parallel breakout board any answers?

    Most motherboard do contain parallel ports, but the port connector may not be at the back (in the section where external connectors will be connected). Instead, the motherboard may contain an LPT ribbon connector on the actual face of the motherboard (usually along one of the edges). You will need a ribbon connector to a DB25 female connector.

    If your motherboard does not contain an LPT header on the motherboard, you can purchase a parallel printer adapter that plugs into one of the PCI slots. The price of the adapter is very inexpensive and sometimes is actually less costly than the actual ribbon connector.

    Click the link to add information to this solution:
    As I am building my 20" x 24" laser engraver cutter, I notice that there is no parallel port on the onboard computer and I have the parallel breakout board any answers?

Get Help with:
This Product
Orders
Tech Support
Sales
This Product
Order Query
Tech Support
Sales
Not logged in. Log In Register
Track Order(s)
View Order(s)
I Want to Schecule a One-On-One Paid Tech Support Session
Book an Appointment Pertaining to a BuildYourCNC Product (Free)
Ask a Quesion Below (Free):
Book an Appointment Pertaining Other Equipment ($60/half hour)
Book an Immedite Appointment Pertaining Other Equipment ($120/half hour)
Ask a Quesion Below (Free):
Waiting for response... I may not answer immediately, but I was notified on my cellular phone so my response is forthcoming. If I don't respond immediately, you can always go to the [My Account] page to see all of our chats at any time.