Our breakout board, does require 5v to operate the correct voltages coming in from the drivers and also coming in from your computer, now the 5V will be supplied by the USB connection, so no external power supply is needed, for either our USB/Parallel breakout board.

Click the link to add information to this solution:
Just for general knowledge. If a spindle gets i.e. 240VAC, and the drivers 36-50VDC for power, why do you need 5VDC for the Breakout Board (BlueBrew)? Is it only for the relay? I think I've seen other BoB's working without power supply, or am I wrong?

Any of the following power supplies will be fine for powering the Mach3 USB controller:
https://www.buildyourcnc.com/item/24v

however, the limit switches do not need high current, so the following power supply is sufficient for the task of connecting limit switches:
https://www.buildyourcnc.com/item/electronicsAndMotors-power-supply-24v-1a-dc

Click the link to add information to this solution:
What power supply do you recommend for the spindle and limit switches if I buy the USB Mach3 breakout board?

We generally use the USB to power the interface (breakout board). The current from the computer is sufficient to supply the breakout board.

Click the link to add information to this solution:
I have a blue brew break-out board. Do I use a seprate power supply for it and what amp output should it have if used.

We generally use the USB to power the interface (breakout board). The current from the computer is sufficient to supply the breakout board.

Click the link to add information to this solution:
I have a blue brew break-out board. Do I use a seprate power supply for it and what amp output should it have if used.

Hi, this BBB comes with a USB port and its cable to power it up. Once connected to the computer a led in the BBB will light up to show it has power.

Additional Information:
Breakout board I have does not have USB port for the 5v power. Does the parallel port supply the 5V power?

Click the link to add information to this solution:
Hi, I need assistance, the parallel breakout board I received looks different from the one on the video, does this one need a 5V supply? If so, where do I connect the positive and where do I connect the ground? Thanks for your help.

For our parallel breakout board (https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay#prettyPhoto/2/) the schematic will show the connections going from the BB to the drivers. The parallel breakout board uses the 25 pin parallel connection to communicate from the computer to drivers, and the USB is used to power the main-board itself, supplying 5V.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
I am wiring my breakout board and it has a USB port on it. Is the USB port there to supply the 5 volt power to it?

For safety's sake I would recommend a new board because they are inexpensive compared to the electronics that they support. Alternatively, it's possible that the one dead pin is a simple fix, such as a bad connection or solder joint; if you feel comfortable making those repairs then it could be worthwhile to check. Finally, if you are not using all the input pins, you could continue to operate the limit switch on pin 11 and hope for the best.

Click the link to add information to this solution:
I have a breakout board and it appears that the pin 12 connection has failed: when i move my limit switches to pin 11 they work; they don't work on pin 12. Do i need a new breakout board?

The USB port on the Parallel Interface board is necessary to supply 5V power. Connect with a USB cable to a USB source.

Click the link to add information to this solution:
I purchased a parallel port breakout board. I have checked all the info and found nothing on the usb port. What is it used for?

We recommend checking the dip switch settings on your drivers, having the correct microstepping/amp settings along with the steps/unit will help the motors run as effective as possible.
This is a default parameter that we use while we test our motors:
Driver dip switch settings will be at a 1/16 microstepping and 2.7amp (11001100) for x/y-axis and the z-axis will be at 1/4 microstepping and 2.7amp (10101100).

In planet-cnc with increasing the motor speed, you will have to modify the settings in planet-cnc (File/settings/setup) you will modify the initial speed, maximum speed, and the acceleration.
X/Y-axis step/unit: 1422.22 initial speed:500 maximum speed:750 acceleration:25
Z-axis step/unit: 1600 initial speed:100 maximum speed:300 acceleration:25
The initial speed and maximum speed will have to be roughly tested and adjusted per application.
Make sure to adjust the JOG slide bard underneath the axis controls on screen to about 750, to compensate for your x/y-axis adjustments. If left alone the speed will max out at the default setting.

Here is a video tutorial to calculate the steps required depending on your mechanical linear motion components. (

Click the link to add information to this solution:
I bought Nema 24 motors and driver package with usb board. What do i need to have more speed? Cant even jog past 25 ipm without the motor stalling (not having enough torgue)

The breakout board has a relay installed and uses the terminals labeled S, O and P. The following link explains the operation of this relay and how to connect the terminals:
https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay#prettyPhoto/8/

You will run your power cord (use an extension cord rather than the actual power cord of the router) through the relay using the S, O and P. The P is a general connection and the S is normally closed (S and P is connected when the relay is not engaged) and O is normally open (O and p are not connected until the relay is engaged).

There are three wires in the power cord: neutral (white), live (black) and earth ground (green). You will run your neutral wire (white wire) through this terminal. At some point in the power cord, remove the outer insulator and expose the three wires within. Cut your neutral wire and strip both ends of the cut. Then insert one end in P and the other end in O (normally open), so Mach3 or other control software you are using will engage the relay and the router will turn on.

You will need to setup your control software to turn on the relay using Pin #16 as this is the digital signal pin that controls the relay.

Click the link to add information to this solution:
What do I need to do to my breakout board to turn the router motor on at the beginning of the program and off at the end?

You will need PlanetCNC software for the USB breakout board and when plugging in the USB the computer should automatically recognize the board, however you can go into device manager to see if the USB terminal is working correctly.
The parallel breakout board; the USB is not a connection terminal rather than a power source, and the parallel port will be the communication terminal.
The items you will need for a water cooled spindle would be: water pump, silicon tubing(length desired by customer), a extension cord(from a hardware store(orange))(1 same gauge wire/length as extension cord).

Click the link to add information to this solution:
I have the usb breakout board https://buildyourcnc.com/Item/electronicsAndMotors-electronic-component-USB-Controller-Breakout and need to run the A axis as a slave the software greys out the box how do I fix this?

Connecting drivers from a controller to the driver does not require relays. A controller typically has pins or terminals for Step and Direction. These terminals connect to the driver's Pulse and Direction terminals. For instance for the X axis: if you are connecting from the Mach3 USB controller, you would connect the XD (X axis Direction) terminal to the Driver's DIR+ terminal, and the XP (X axis Pulse) to theDriver's PUL+ terminal, and the GND from the controller to the PUL- and DIR- terminals.

I have thorough step by step instruction for two controllers:
https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board
https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Click the link to add information to this solution:
When you are talking about relatys, that is all Greek to me. Will a breakout board do what I need to hook up to my drivers?

I recommend using a wireless pendant rather than one that is wired to the controller.

Here is a link to one on Amazon.com: https://amzn.to/3r3AfTm

This is an affiliate link.

Click the link to add information to this solution:
[596] I am new to CNCs, curious to know what I need to look for in a pendant that would be compatible with this board and Mach4?

To control a spindle using the USB CNC interface, you will need a relay board that contains a transistor that can activate the relay with a power source with enough current that can activate the relay. This video explains all of the information you will need to develop this relay circuit:

Click the link to add information to this solution:
i have a breakout usb controller iam using a spindle output to active a relay 5V but it didnt work.... whats the problem, what else i need to active that realy 5v 10A?

I would not recommend slaving an axis using the method of taking an additional axis from the USB interface. Instead, wire both drivers to a single axis on the USB interface. This will insure perfect signal output to both drivers. If you requre the motors to spin in opposite directions, simply wire one of the motors to the driver reversing the coil A and B connections, or use a hex inverter (https://www.buildyourcnc.com/tutorials/Tutorial-Two-Motors-Spinning-Oppositely-On-Single-Axis).

Click the link to add information to this solution:
I purchased a USB Breakout board, motors and drivers, paid for CNC USB Controller Software and I CAN NOT "Slave" an axis, but there is an option to do that. The moment I connect USB Breakout Board "Slave" option becomes shaded and I can no longer select it (becomes not functional). What is going on? Need help asap. Thanks

I would suggest using the NPN proximity sensor for the Mach3 USB or the Pokeys57cnc. The proximity sensors have a top DC voltage limit of 30 volts, so it would be best to use the 24V power supply that is used to power the controller. Both controllers have a 24V power requirement, so that is convenient.

The blue wire of the proximity sensor is the GND wire and is connected to the 24V power supply's V- terminal. The brown wire is the positive wire and is connected to the V+ terminal of the 24V power supply. The black wire is the signal wire and is connected to the input terminal of the controller.

Click the link to add information to this solution:
Good evening, if I wanted to use your inductive proximity sensor's with your USB interface board what would I need besides the sensors I would be using 5 of the sensors. I have a 48V 12amp power supply. Thank you

I would recommend using a separate 24VDC power supply for the controller. The 24VDC that is connected to the controller is used for delicate input signals and output signals that control external devices. To keep interference and possible current and voltage fluctuations at a minimum due to the motor load, a separate power supply would be best.

Click the link to add information to this solution:
[575] Can the 24VDC supply used for the interface board be the same supply used for stepper drivers, or do you need separate power supplies? If not, does GND and DCM need to be isolated?

If you would like to add a laser to a plasma table, you will need the following parts:

Laser tube at 40 watts:
https://www.buildyourcnc.com/item/Laser-Component-Laser-Tube-CO2-40Watt

Mirror mounts (this will depend on the way you mount the laser tube):
https://www.buildyourcnc.com/item/Laser-Component-Mirror-Mount-20mm

Mirrors for the mirror mounts:
https://www.buildyourcnc.com/Item/Laser-component-20mm-mirror-25mm

Laser Tube Power Supply:
https://www.buildyourcnc.com/item/Laser-Component-Power-Supply-CO2-40W

Laser Focus Lens:
https://www.buildyourcnc.com/item/laser-component-20mm-lens-2-inch-50!80mm

Mirror and Lens Mount and Nozzle:
https://www.buildyourcnc.com/item/Laser-Component-Nozzle-20mm-lens-mirror

High Tension Extension Cable:
https://www.buildyourcnc.com/item/Laser-component-Power-Supply-High-Tension-extension-wire

Laser Control System:
https://www.buildyourcnc.com/item/Laser-Component-Laser-Control-System

Screw Posts (to connect the high tension and return wire to the laser tube, highly recommended as the leads on the laser tube are fragile):
https://www.buildyourcnc.com/item/laser-component-newbiehack-connectors-screw-terminal-binding-post

Safety Eyewear for CO2 laser wavelength:
https://www.buildyourcnc.com/item/laser-components-goggles-safety-tinted

Click the link to add information to this solution:
I have an Eagle Plasma table and I want to add a 40 laser. Can you supply me a list of what I need to make this happen.

You will need a USB cable to connect the computer and the Mach3 USB. The 64-bit operating system must be Windows and you will need the Mach3 CNC control software installed on the operating system.

You will need to install the USB driver called RNRMotion.dll. You can find the driver here: https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Move the file to your Mach3 Plugins folder Example: "C:/Users/ProgramFiles/Mach3/Plugins"

Mach3 will prompt you to select a driver and this is where you can select the "RnRMotionController" and check "Don't ask me again". This will allow your board to communicate with Mach3.

You will also need the xml file found on this page: https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

On that page, you will need to download the XML Mach3 Config File by right clicking on the link and selecting "save as". Save the Mach3Mill.xml file in your Mach3 root folder.

That file is the main configuration file for the Mach3 board. It has all of the typical settings that the Mach3 board needs.

Click the link to add information to this solution:
I have a 64 bit operating system and the Mach3 usb control board. What do i need to communicate between the two?