You are just sending a lot off dust

Additional Information:
are you able to supply a control board only

Additional Information:
Yes.

Click the link to add information to this solution:
you have asked me a ? that I do not know what you are talking about

For safety's sake I would recommend a new board because they are inexpensive compared to the electronics that they support. Alternatively, it's possible that the one dead pin is a simple fix, such as a bad connection or solder joint; if you feel comfortable making those repairs then it could be worthwhile to check. Finally, if you are not using all the input pins, you could continue to operate the limit switch on pin 11 and hope for the best.

Click the link to add information to this solution:
I have a breakout board and it appears that the pin 12 connection has failed: when i move my limit switches to pin 11 they work; they don't work on pin 12. Do i need a new breakout board?

The breakout board has a relay installed and uses the terminals labeled S, O and P. The following link explains the operation of this relay and how to connect the terminals:
https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay#prettyPhoto/8/

You will run your power cord (use an extension cord rather than the actual power cord of the router) through the relay using the S, O and P. The P is a general connection and the S is normally closed (S and P is connected when the relay is not engaged) and O is normally open (O and p are not connected until the relay is engaged).

There are three wires in the power cord: neutral (white), live (black) and earth ground (green). You will run your neutral wire (white wire) through this terminal. At some point in the power cord, remove the outer insulator and expose the three wires within. Cut your neutral wire and strip both ends of the cut. Then insert one end in P and the other end in O (normally open), so Mach3 or other control software you are using will engage the relay and the router will turn on.

You will need to setup your control software to turn on the relay using Pin #16 as this is the digital signal pin that controls the relay.

Click the link to add information to this solution:
What do I need to do to my breakout board to turn the router motor on at the beginning of the program and off at the end?

Software specific questions for Planet-CNC will have to come from them or other sources as we are not fully equipped to troubleshoot all issues. If the issue is related to motor tuning or setup involving our electronics, then we will gladly assist you. You may contact techsupport@buildyourcnc.com with inquiries.

Click the link to add information to this solution:
What do I need to purchase from you to get me running. I have planet cnc control board but it is difficult contacting them when I need help.

Attaching two motors in parallel is possible, but you will need another motor and driver for the opposite side. Each motor must have its own driver to work accordingly and fluently. The two can be wired together, to the same pins on your breakout board and set the dip switches on the driver to match the ones on your x-axis(ex). But remember to view the orientation of the motor and which way it spins, since it is on the opposite side it will have to be orientated correctly to move in sync with the other motor.

Click the link to add information to this solution:
I just finished building my first CNC with the electronics I purchased from you and I am already thinking about improving it. I would like to build a 2 motor X axis solution. Is it possible to attach 2 parallel motors and drivers to the BlueBrew Breakout Board? If so, how?

Did you connect the USB connector to the breakout board?

Additional Information:
YES I CONNECTED THE USB TO THE BREAKOUT BOARD

Click the link to add information to this solution:
I connected the electronics (for 2 x 4 feet) that I ordered from you. But how do I check if I connected all the wiring properly. There is neither any light on motor drivers nor on breakout board. And the motor shaft also does not move before and after the power supply is given.

Our breakout board, does require 5v to operate the correct voltages coming in from the drivers and also coming in from your computer, now the 5V will be supplied by the USB connection, so no external power supply is needed, for either our USB/Parallel breakout board.

Click the link to add information to this solution:
Just for general knowledge. If a spindle gets i.e. 240VAC, and the drivers 36-50VDC for power, why do you need 5VDC for the Breakout Board (BlueBrew)? Is it only for the relay? I think I've seen other BoB's working without power supply, or am I wrong?

We could not guarantee, nor say, whether or not your current software would be able to utilize the USB breakout board. Our USB breakout board is designed for use with Planet CNC software found here, http://www.planet-cnc.com/index.php?page=software

As far as we know, this is the only CNC Controller software that operates on a USB breakout controller.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
I want to change my old DSP controller and break out board with new one in your site that support usb it is possible ? if yes can we contact us to talking about details ?

The redLeaf CNC computer systems will have either Mach3 or LinuxCNC installed as per the customer's request. If the Mach3 license is purchased, the license file will also be installed on the redLeaf CNC computer system.

The Mach3 or LinuxCNC settings will be configured during the assembly of the system. We contact the customer to determine the drive (mechanics) and inertial (weight of gantry and other parts of the gantry) specifications in order to correctly configure the steps per inch, velocity and acceleration.

Click the link to add information to this solution:
I ordered a redLeaf with Mach3 installed. Do you guys configure any of the setting in mach3 or will I need to do that all myself?

The USB port on the Parallel Interface board is necessary to supply 5V power. Connect with a USB cable to a USB source.

Click the link to add information to this solution:
I purchased a parallel port breakout board. I have checked all the info and found nothing on the usb port. What is it used for?

You should have no problem connecting the Pokeys57CNC controller to the drivers of your machine as long as the drivers have step (Pulse or PUL) and direction (DIR) terminals. You will need the cable pack that is sold separately so you can connect the headers/connectors of the pokeys57cnc controller to the drivers using ribbon cables.

I show this process in great detail on this page:
https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Is you scroll down on the page, you will see a set of videos that show the process step-by-step.

Click the link to add information to this solution:
I have a ShopBot CNC that was converted to Mach 3. The controller has gone out. I pourchased your Pokeys57 board, but I'm not sure I have everything I need. I think my motor drivers are OK, but am not sure how to wire them to what I purchased from you. Need Help. How can we make this work, or do I need a different board to distribute the movement signals to my drivers?

Any of the following power supplies will be fine for powering the Mach3 USB controller:
https://www.buildyourcnc.com/item/24v

however, the limit switches do not need high current, so the following power supply is sufficient for the task of connecting limit switches:
https://www.buildyourcnc.com/item/electronicsAndMotors-power-supply-24v-1a-dc

Click the link to add information to this solution:
What power supply do you recommend for the spindle and limit switches if I buy the USB Mach3 breakout board?

Here is how to connect your router to the parallel breakout board through the on-board relay. You will need a spare extension cord. You will need to remove a portion of the outer jacket of the extension cord to expose the white, black and green wires (white = neutral, black = live and green = ground), understanding that the neutral and live create the completed circuit.

See this image of a similar connection. The terminal has the same connections.
https://www.buildyourcnc.com/images/vacuum-pressure-controller-relay-terminals-700.JPG

Image of the relay terminal:
https://www.buildyourcnc.com/images/breakoutboardrelayNONC.PNG

The live/black wire would be cut and one end of the cut would be secured into the P terminal and the other cut end would be secured into the S terminal. The live and ground wire would be uncut and travel from the plug to the router.


Additional Information:
You can also connect other high powered devices to the breakout board using any of the output terminals. You will need to supply extra relays like the one shown here:
https://www.buildyourcnc.com/item/electronicsAndMotors-breakout-Relays-relay-board-250V-12A-5V

Or you can find SSRs (Solid State Relays) that will accept 5v to drive the relay coil. Make sure the SSR will protect the 5V line from Back EMF as there is a coil in the relay. The one we sell contains a fly-back diode to protect the 5v terminal.

Click the link to add information to this solution:
I have your breakout board with relay parallel port , how can I wire up a regular router to that board so I can control the router

Does your plasma cutter have an external trigger that voltage can be applied to make the trigger engage? If I known, please provide the brand and model of your plasma cutter so we can determine this.

Additional Information:
I converted my blackToe to do plasma cutting. Used the Motor control relay on the break out board and just wired it into the plasma cutter trigger. Put a large pan (like a car oil drip pan) with about 1/4 inch of water on the table and attached fixtures. 400 15ga parts later it's still working great.

Additional Information:
That is so cool!!

Additional Information:
I would like to post a story on your setup and conversion. Do you have pictures of the process and/or the new setup?

Click the link to add information to this solution:
Hello I bought a full setup of parts a couple years ago to make a cnc router and now I have decided that I want to make a cnc router/plasma. I was wondering how to go about hooking up the plasma to the breakout board

We are working on a keypad that will connect to the USB interface. It is possible to create a quick keypad using perf-board and some push buttons. All you need to do is connect one side of the switch to the pin of the axis and direction and the other side of the push button to the 5v pin. The datasheet shows the pinout of the jog connector.

Additional Information:
I had found the pins to wire in a job connector. My question is, what sort of connector do I look for (on Amazon for example) that will work for each 2 pin pair? I suspect they are the same as the connector for power and reset on my computer's motherboard, but I have no idea what to look for (what to buy).
thanks.

Additional Information:
20

Click the link to add information to this solution:
I need to find a connector(s) to wire a pushbutton array to the USB board I purchased. Do you sell such a connector. Can you tell me what to look for?/What such a connector is called?

The Mach3 USB board will fit in the redLeaf, but you may need to modify the Plexiglas top for proper mounting. However, the redLeaf has the proper parallel GPIO on the motherboard for use with the Parallel breakout board. If you have a laser on the machine you are using, then I would urge you to maintain the parallel breakout board as the Mach3 USB board will not work correctly using the Z-direction pin and you will need to determine how to use the output pins onthe USB board to ensure proper laser functionality.

Click the link to add information to this solution:
Will Mach3 USB Interface board fit in my redleaf, in lieu of the breakout board that came with it?

Does your breakout board (interface) have a relay? If so, you can connect one of the router/spindle's ac lines through the relay. The M3, M4 and M5 codes are used to control the router/spindle. Typically, the M codes are automatically added to the g-code regardless if you configure this in your CAM software. If you have the breakout board from buildyourcnc, you can go to the product page for the breakout board and the relay connection diagram and narrative is in the instructions on that page.

Click the link to add information to this solution:
WHAT IS THE MOST EASY WAY TO HOOK UP MILL IN THAT AUTOMATICALLY STARTS WHEN CYCLE STARTS, AND STOPS GCODE THROUGH?

What we intend our customers to use for wiring the motors to the drivers will be 4 conductor 20 AWG cable, now for the PSU to Drivers; 16-18 Gauge wire should be used, and drivers to BB(Breakout Board) should be a 24 AWG wires.

Click the link to add information to this solution:
In my 4'x8' Blackfoot rig, there is a maximum wire length of 16" between drivers, breakout board, and power supply as well as a maximum wire length of 10' from drivers to motors. What AWG wires should I use to connect power supply to drivers, drivers to motors, and drivers to breakout board?

The datasheet for the parallel breakout board is here:
https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay#prettyPhoto/2/

The datasheet for the USB interface is here:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout#prettyPhoto/2/


Additional Information:
20

Click the link to add information to this solution:
I need wiring instructions for the breakout board you sent yesterday. It is not like the one in the videos and I don't know where to connect the 5V. No data sheet or anything.