To stop the laser completely from continuous firing after a job is complete, I recommend to have your file to end while reaching the clearance plane which you will enter in your CAM software. Make sure that your clearance plane value is very small (ex.) 0.001 above 0 and activates at -0.001 also adding a additional g-code manually that raises the z-axis towards the end of the job/run(only if experienced would we recommend using this). This will turn of the laser, rather than the laser staying on and at its current height.

When activating the emergency e-stop, (personal opinion) I would wire the e-stop at the beginning of the live/load wire going to the electronics power supply and the laser power supply.
It will be in at the beginning of the y connection, (https://buildyourcnc.com/blackToothLaserCutterAndEngraver.aspx#prettyPhoto/13/) so you will cut power to both instead of just the CNC electronics.

Click the link to add information to this solution:
Need help configuring Planet CNC software to control laser firing. Currently it is firing using the Z axis but leaves the laser on after a run or when the emergency stop is activated. HELP!!

Looking for a solution myself. Proper operation would be for the limit switch to only disable further travel in the effected direction while still allowing travel in the opposite direction.

As for now, I am just using the jog arrows within the software or the VGA controller.

Click the link to add information to this solution:
After limit switch is activated on planet cnc control software, what do I need to do to get axis to move again?

When you plug the USB controller into the computer using a USB cable, and the planet-cnc software is running, you will be presented with a dialog box that will contain a text box for the key that you received from the planet-cnc folks.

Additional Information:


Additional Information:
Is there any other software that will work with your controller Mach3? Thanks for the help!

Click the link to add information to this solution:
However it how do I get the software to work? PlanetCNC sent me a key that looks like it will only work with a backup control board I purchased from them?

Connecting drivers from a controller to the driver does not require relays. A controller typically has pins or terminals for Step and Direction. These terminals connect to the driver's Pulse and Direction terminals. For instance for the X axis: if you are connecting from the Mach3 USB controller, you would connect the XD (X axis Direction) terminal to the Driver's DIR+ terminal, and the XP (X axis Pulse) to theDriver's PUL+ terminal, and the GND from the controller to the PUL- and DIR- terminals.

I have thorough step by step instruction for two controllers:
https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board
https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Click the link to add information to this solution:
When you are talking about relatys, that is all Greek to me. Will a breakout board do what I need to hook up to my drivers?

You should have no problem connecting the Pokeys57CNC controller to the drivers of your machine as long as the drivers have step (Pulse or PUL) and direction (DIR) terminals. You will need the cable pack that is sold separately so you can connect the headers/connectors of the pokeys57cnc controller to the drivers using ribbon cables.

I show this process in great detail on this page:
https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

Is you scroll down on the page, you will see a set of videos that show the process step-by-step.

Click the link to add information to this solution:
I have a ShopBot CNC that was converted to Mach 3. The controller has gone out. I pourchased your Pokeys57 board, but I'm not sure I have everything I need. I think my motor drivers are OK, but am not sure how to wire them to what I purchased from you. Need Help. How can we make this work, or do I need a different board to distribute the movement signals to my drivers?

You will need a USB cable to connect the computer and the Mach3 USB. The 64-bit operating system must be Windows and you will need the Mach3 CNC control software installed on the operating system.

You will need to install the USB driver called RNRMotion.dll. You can find the driver here: https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Move the file to your Mach3 Plugins folder Example: "C:/Users/ProgramFiles/Mach3/Plugins"

Mach3 will prompt you to select a driver and this is where you can select the "RnRMotionController" and check "Don't ask me again". This will allow your board to communicate with Mach3.

You will also need the xml file found on this page: https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

On that page, you will need to download the XML Mach3 Config File by right clicking on the link and selecting "save as". Save the Mach3Mill.xml file in your Mach3 root folder.

That file is the main configuration file for the Mach3 board. It has all of the typical settings that the Mach3 board needs.

Click the link to add information to this solution:
I have a 64 bit operating system and the Mach3 usb control board. What do i need to communicate between the two?

No, we have gotten away from the planet-cnc boards as they have decided to not support our board with their software. You can use the Mach3 USB board as an alternative. You will be better off with Mach3 as a control software as this is widely used and supported.

Mach3 USB board:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Click the link to add information to this solution:
I have the older discontinued USB breakout board. The y-axis no longer works and have traced it to the breakout board. Is there a replacement board that can use the same Planet CNC software running on Windows 10?

At this time we are working to release a new USB controller board that will be compatible with Mach4 software and do not have any immediate plans to update the Planet-CNC USB board.

Click the link to add information to this solution:
Are there plans to release a USB Controller to work with the Planet CNC Output Board for more advanced spindle control from within Planet CNC?

Here is a list of the parts needed to get the electronics combo functioning (parallel or USB interface options):

- 22 or 24 gauge stranded hookup wire to connect all of the drivers to the USB or parallel interface (terminal to terminal connections),
- 18 gauge stranded hookup wire to connect the drivers to the power supply,
- a power cable (extension cord) to connect from the power outlet to the power supply,
- 4 conductor cable to connect the drivers to the stepper motors,
- a USB cable to connect from the computer to the USB interface (or for power to the parallel interface),
- for the parallel interface, a parallel cable is needed (male to male db-25),
- a computer (for parallel interface, the computer will need a parallel port and if the computer does not contain a parallel interface, the motherboard may have a header for it, or you can purchase a parallel adapter to plug into the motherboard, very inexpensive),
- cnc control software: for the USB interface, you will need planet-cnc software, for the parallel interface, you can use any industry standard cnc control software (the typical is Mach3 for Windows, or EMC2 or Linuxcnc for Linux (Linuxcnc.org).

5v power supply is not needed. The 5 volts signal level power is derived from the computer through USB on both types of interfaces.

Click the link to add information to this solution:
What else to I need to purchase along with the "3 Axis Electronics Combo w/ USB Interface Board" to get the electronics up and running? (software, 5V power supply, 4-conductor wire, etc.)

We would highly recommend using our forums to sell you machine buildyourtools.com.
We currently do not have a page or option to allow our customers to sell our machines, you can also contact us at customerservice@buildyourcnc.com, for further assistance dealing with the machine and in regards to selling it.

Click the link to add information to this solution:
I have a blueChick 13"x24" or 13"x36" Desktop CNC Router Kit v3.0 (Timing Belt) that I've assembled but never was able to get it running. Can BuildYourCNC assist me in selling this machine? Do you have used machine offerings on your site?

You will need to look for the parameter that controls the run frequency. The frequency can be controlled bu the panel, external terminals, or the RS485 TX/RX terminals (UART protocol). You will want to change that parameter so it uses the panel. If you are referring to the maximum panel dial frequency is only allowing 200-300 rpm, then look for the parameters to control the frequency.

For 200 RPM:
Hz = 200/60 = 3.33 Hz

For 300 RPM:
Hz = 300/60 = 5 Hz

Conversion to RPM:
If you ever find yourself yearning to reverse-engineer the process, the formula is as follows:

RPM = Hz × 60

Look for values that match somewhere between 3 and 5 in your frequency parameters and replace them with 400 to give you 24,000 RPM max.

Click the link to add information to this solution:
[77] Hello. I’m interested in buying a water cooled spindle and VFD. I have an Avid Pro CNC and would love to control it using Mach 4 but I keep hearing it’s difficult to integrate. Also, is the water pump 120 or 240? I’d love any advice etc. eBay is a web of confusion with all of the options. Thank you.

For our redFly there is no need for firmware, however you will need to purchase a license for the board. Which you can buy here: (http://planet-cnc.com/product/cnc-usb-controller-license/)
The license is to completely unlock the software Planet-CNC.

Click the link to add information to this solution:
i have a redfly box for a greenbull 5x10 do I need to load a firmware to use planet cnc or is it already done

Yes, you can use a conductive metal to serve as a zeroing block for the Z axis. All you need to do is connect the block (conductive metal) to one of the 4 inputs on the controller. The end mill must be connected to the DCM terminal (the GND of the 24V power supply) of the controller. In the inputs dialog box (config-ports and pins-inputs). Under the probe line, enter port 3 and the pin used for the block.

Click the link to add information to this solution:
[575] Hi can I use a zeroing block with mock three interface board and do you have one I can purchase and directions on how to set up

Yes, we can help you with leveling your CNC machine even if you didn't purchase it from us.

Click the link to add information to this solution:
[789] I need to level my cnc machine, but I didn't purchase it from you, so: Do you offer tech support with leveling a cnc? Because I don't see this problem listed .And: Do you offer support if my machine was purchased in China or from another vendor?

Hi, you can call me at the 281-815-7701 number. Please leave a message when you call as most of the calls are screened to avoid scam calls. You can also email me at customerservice@buildyourcnc.com or phooddaniel@berkeley.edu.

The newer kits that are featured on the home page include everything you need except a computer and software. The legacy CNC routers that are located in the CNC machines menu selection include all of the parts for the gantry, but you will need to build the table yourself. All of the information on the measurements to be followed for the table construction are on the machine pages.

Click the link to add information to this solution:
I am looking at getting a 4x8 cnc router kit. I am having a hard time figuring out what is included in the kit and what else i will need to buy with it to get off the ground and running. Is there someone i could talk to to walk me through it? If not, can you break down what all I need to go from scratch to a running set up? thanks

Do you have Windows 10? Did you do a major update on Windows 10? Many customers are finding that the most recent (6/3/2018) update of Windows 10 is crashing Mach3. Contact Machsupport.com to inform them of this problem.

Click the link to add information to this solution:
I have purchased Mach 3 license, motors, drivers, and break-out board from you.....gotten it all working..... but recently, a friend tried to help me load Alpha Cam toolpath code with no success, now Mach 3 won't even load. how do I get it working again?

Yes, we can create an only wood kit for you. Please give us a call on Monday to provide your name so we can look it up in our system to confirm your previous purchase and we will provide a PayPal invoice for the kit, since this is a special case.

Click the link to add information to this solution:
Is it possible to purchase the wood pieces only for a BlackToe 2.0/2.1? I have all of the hardware from my kit, but the wood pieces were lost in a recent move.

I have not come across this problem, but there may be USB, or firmware issues that you are experiencing. I would recommend going on the polabs website and using their support center (https://support.poscope.com/)and posing that question to them. Also, have you tried the ethernet port as an alternative to see if that helps?

Here is the response from an LLM:

Check USB Cable and Port: Start with the basics. Sometimes this error is due to a poor USB connection. Ensure you're using a high-quality, shielded USB cable and that it's plugged into a USB port directly on your computer, not through a hub. If possible, try a different USB port or a different cable to rule out any issues there.

Update Firmware and Software: Ensure that both your PoKeys57CNC firmware and the Mach4 software are up to date. Firmware updates for your PoKeys board might include optimizations or fixes that address connectivity issues.

USB Polling Rate: This error can also arise from the USB polling rate setting in the PoKeys configuration software. It might be set too high for your system's ability to handle it. Try lowering the polling rate and see if that resolves the error.

Computer Performance: Check your computer’s performance. If it’s running several heavy applications simultaneously, it might not be able to process signals from the PoKeys board fast enough. Try closing unnecessary applications or consider using a dedicated machine if your current setup is too taxed.

Mach 4 and PoKeys Plugin Configuration: Dive into the Mach 4 plugin configuration for PoKeys. Ensure that all settings are correctly configured as per the manual. Incorrect settings might lead to communication bottlenecks.

Connection Quality and Interference: Consider any potential interference sources near your CNC setup or computer. Electromagnetic interference from large motors, other electronics, or long cable runs can affect communication quality. Try rearranging your setup to minimize interference.

Consult Documentation and Support: If the issue persists, consult the detailed documentation provided by PoKeys or reach out to their customer support. They can offer more specific advice based on the latest product updates or known issues.

Click the link to add information to this solution:
I HAVE FOLLOWED YOUR YOUTUBE VIDEO ON SETTING UP THE POKEYS 57CNC BOARD BUT WHEN OPEN MACH 4 GET A ERROR MESSAGE CONNECTION IS TO SLOW

Come on over and we will assist you in any way you need.

Click the link to add information to this solution:
I purchased a Blackfoot 4ft X 8ft in 2015 I have yet to run it. Do y’all offer any classes that can help me?? I would very much like to have this machine running. Thank you in Dayton Tx