Attaching two motors in parallel is possible, but you will need another motor and driver for the opposite side. Each motor must have its own driver to work accordingly and fluently. The two can be wired together, to the same pins on your breakout board and set the dip switches on the driver to match the ones on your x-axis(ex). But remember to view the orientation of the motor and which way it spins, since it is on the opposite side it will have to be orientated correctly to move in sync with the other motor.

Click the link to add information to this solution:
I just finished building my first CNC with the electronics I purchased from you and I am already thinking about improving it. I would like to build a 2 motor X axis solution. Is it possible to attach 2 parallel motors and drivers to the BlueBrew Breakout Board? If so, how?

The board layout is different and the terminals have slightly different names, but the two boards function the same. The wiring diagram is the same for both boards. The plug-in driver for Mach3 is also the same, so you should not have a problem. If you do run into an issue, please let me know here and I will help you determine the problem.

Thanks

Additional Information:
Thank you for the assurance that the boards will function the same. You did not answer the primary question of wiring. The diagram shows a board with a 5V for each axis, the new boards have only 1 5V point on the axis side. In retrospect since this controller receives information and most possibly the 5V signal directly from the computer leading to the drivers. I will wire the X, Y and Z axis to the single 5V point and see what happens.

Click the link to add information to this solution:
received my mach 3 USB breakout board today. The layout of the board is different from your diagram which shows a 5V power slot for each axis. Do I wire the 5V slot with only one 5V wire from one of the drivers or perhaps wire all three 5V wires into the one 5 V slot. Please advise.

Did you connect the USB connector to the breakout board?

Additional Information:
YES I CONNECTED THE USB TO THE BREAKOUT BOARD

Click the link to add information to this solution:
I connected the electronics (for 2 x 4 feet) that I ordered from you. But how do I check if I connected all the wiring properly. There is neither any light on motor drivers nor on breakout board. And the motor shaft also does not move before and after the power supply is given.

https://buildyourcnc.com/Item/electronicsAndMotors-electronic-component-e-stop-button-switch-safety#prettyPhoto/0/

Click the link to add information to this solution:
How do I wire up multiple E-stop to breakout board, does each E-stop need there own pin? If not since there are only 4 screws on stop 2 for no and 2 for nc do you just splice the wires together if your only using 1 pin? Thanks

Any of the following power supplies will be fine for powering the Mach3 USB controller:
https://www.buildyourcnc.com/item/24v

however, the limit switches do not need high current, so the following power supply is sufficient for the task of connecting limit switches:
https://www.buildyourcnc.com/item/electronicsAndMotors-power-supply-24v-1a-dc

Click the link to add information to this solution:
What power supply do you recommend for the spindle and limit switches if I buy the USB Mach3 breakout board?

Did this spindle come with a 110V 1.5kW VFD?

Additional Information:
The reason I ask is because the 220V 1.5kW spindle may work well with the 110V 1.5kW VFD. I believe we did the test prior to shipment.

Additional Information:
I have a 110V HY01D511B VFD already. I did not know they would work together. I will give this a try.

Additional Information:
If you did't get the VFD paired with the spindle from us, then I would not connect the 220V spindle with your VFD. Let me ask my technician and get back with you.

Additional Information:
My technician said that it should work since the 220V 1.5kW spindle worked with our 1.5kW 110V VFDs.

Remember to seek the advice and guidance of a professional electrician when connecting these types of high powered devices.

Additional Information:
Do you have any info on the settings? I would rather buy a pre-configured VFD from you if you don't have the settings for my HT since I have already fried one spindle because of lack of documentation from the manufacturer. If you can setup a VFD that works with the spindle you sent at 110v input voltage I would be fine with the extra expense.

Click the link to add information to this solution:
I ordered a 1.5KW 110 volt spindle. I just received the box and the spindle clearly says on the foam packaging and the side of the spindle that it is 220V. I think you shipped me the wrong spindle

Yes, if the power supplies were supplied by us, we will exchange them with 110v equivalent power supplies.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
Hello, I am a student working on a CO2 laser. We recently ordered two 40watt CO2 laser tubes and two 40 Watt CO2 Laser Tube Power Supply at 220V. However, our school is unable to use them due to being 220v. Is it possible to exchange these for the 110v supply, or is there a way we can go about connecting it at 110v instead of 220v? Thank you.

The datasheet for the parallel breakout board is here:
https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay#prettyPhoto/2/

The datasheet for the USB interface is here:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout#prettyPhoto/2/


Additional Information:
20

Click the link to add information to this solution:
I need wiring instructions for the breakout board you sent yesterday. It is not like the one in the videos and I don't know where to connect the 5V. No data sheet or anything.

You will want to connect the homing switches (which may also serve as your near limit switches) to different input terminals. It's ok to add more limit switches with the home switches, but each home should be on independent inputs. For example, connect home X and any other limit switch to IN1, connect home Y and any other limit switch to IN2, and so on. This will allow you to properly use the "ref all home" button in Mach3.

Additional Information:


Additional Information:
In the instructions (diagram 1) you show all the home switches connected in parallel? But here you say they need to each have their own inputs. "You will want to connect the homing switches (which may also serve as your near limit switches) to different input terminals." I dont see how the second and third axis can go home if the first axis has already closed the parallel circuit unless they back off a bit until the switch opens up again before the next axis goes to home? My machine has no limit switches so I assume they are home switches.

Click the link to add information to this solution:
[575] I have finally got my limit switches wired and working - thank you. Can they also used as homing switches and if so it it just a question of looping the two inputs on the board i.e. the limit and home terminals IN2 to IN3

Hi, this BBB comes with a USB port and its cable to power it up. Once connected to the computer a led in the BBB will light up to show it has power.

Additional Information:
Breakout board I have does not have USB port for the 5v power. Does the parallel port supply the 5V power?

Click the link to add information to this solution:
Hi, I need assistance, the parallel breakout board I received looks different from the one on the video, does this one need a 5V supply? If so, where do I connect the positive and where do I connect the ground? Thanks for your help.

Sure, connect O2 (output #2) on your mach3 USB board to the GND side of your relay coil. Connect the 24V power supply to the positive side of your 24v relay.

You will want to connect a flyback diode (1N4007) between the coil connections to make sure the coil back current does not damage the Mach3 USB board.

Refer to this diagram:
https://www.buildyourcnc.com/Documents/Electric%20Wiring%20Diagram.pdf

Please let me know if this helps and if you need further guidance.

Thanks

Click the link to add information to this solution:
I recently purchesed a USB Mach3 breakout board and need help setting mach3 to use a relay to start the router can you show how to set the pins and which port to use on the board to attached the relay?

You will need PlanetCNC software for the USB breakout board and when plugging in the USB the computer should automatically recognize the board, however you can go into device manager to see if the USB terminal is working correctly.
The parallel breakout board; the USB is not a connection terminal rather than a power source, and the parallel port will be the communication terminal.
The items you will need for a water cooled spindle would be: water pump, silicon tubing(length desired by customer), a extension cord(from a hardware store(orange))(1 same gauge wire/length as extension cord).

Click the link to add information to this solution:
I am making my own CNC setup using all the electronics from your website and I have many questions. Please advise how to have my computer recognize the USB connection from my breakout board also I would like to use a water cooled spindle but I need to know the parts required for a 4x10 bed area used for woods and plastics

Do you have the Pokeys57CNC connected to a 24V external power supply?

Additional Information:
Yes, a 24V external power supply with the jumper positioned. I'm using the ethernet port so the 24v is the only source of power. I plan to measure the amp draw when I have a chance to see how much the vfd is drawing on the analog out.

Additional Information:
Further information. The resistance across the terminals on the vfd is 22k ohms. With an independent 0-10v current source I can run the spindle from 20 to 400 Hz. The PokeysCNC only gets to 3.8v with the vfd attached (and the vfd is at 150 Hz) compared to 10v when the vfd is not attached. The power to the PokeysCNC is steady at 24.18 V, so I'm not maxing out the power supply. Still looking for thoughts on what might be going on?

Additional Information:
And the other thing - The measured amperage is 0.17 mA for the 0-10 V signal (which makes perfect sense for 3.7 V and 22k Ohms).

Additional Information:
Just to bring finality to this issue - I added a 2.2 microfarad capacitor across the 0-10V input terminal (from signal to ground). This solved the issue. Evidently, it was an electrical noise issue.

Click the link to add information to this solution:
My pokeysCNC board creates and analog signal of 0-10V for 0 to 24000 spindle rpm just like it should from Mach3. However, when the spindle is on, the voltage only gets to about 3.8V for 24000 rpm. It seems like the vfd is drawing more current than the pokeyscnc analog output can produce. It there an easy solution to this problem?

If you already have a Mach3 license, you don't need to purchase another one. The license is connected to you rather than the computer. Mach4 is licensed to the computer, but you are able to have multiple computers for each license, and can be switched from one computer to another.

If you purchased the license from me, you can call (make sure to leave a voicemail), or email to get a re-issued license.

Click the link to add information to this solution:
[575] I have an older CNC (2018) which has been working fine. The Windows 7 PC crashed and I am trying to get operational again using a windows 10 machine. I will have to buy a new license for the Mach 3 so will need to get the interface board I have to talk to MAch 3. Can I get just the disc or is there a place I can download what I need?

I would recommend using a separate 24VDC power supply for the controller. The 24VDC that is connected to the controller is used for delicate input signals and output signals that control external devices. To keep interference and possible current and voltage fluctuations at a minimum due to the motor load, a separate power supply would be best.

Click the link to add information to this solution:
[575] Can the 24VDC supply used for the interface board be the same supply used for stepper drivers, or do you need separate power supplies? If not, does GND and DCM need to be isolated?

First, you should check the configuration in your CNC control software and determine if the spindle control pin is correctly set. That pin will engage the relay.

The P and O position of the relay is set as Normally Open where the relay is open (open circuit, or no connection) at idle and when engaged will be closed (closed circuit, or connected). If you suspect that the relay is damaged, the recommended action would be to disconnect the spindle from the relay and operate the spindle/VFD manually using the Run and Stop buttons on the face of the VFD (until the breakout board can be replaced).

Click the link to add information to this solution:
The spindle has started on my Machine while the machine was sitting idol, I'm not sure if the relay has failed on the breakout board. Is there a way to test this?

The fact that you cannot move the motors with the keyboard serves as a clue to a couple possibilities.

- The software may not be communicating with parallel port. (One possibility may be that your step pins are not low active, or vice versa depending on your drivers).
- You may not be in the correct tab of Mach3. Make sure you are in the Program Run tab.
- The jog on/off button on the program run screen may not be lit (invoked).

This address below shows the complete troubleshooting for this type of situation. It will show how to test each pin at the parallel port at the back of the computer and everything else associated with correctly wiring the electronics.

https://buildyourcnc.com/CNCElectronicsandWiring.aspx




Additional Information:
6 axis robot with Mach3 Card 6 Axis Motion Controller

Click the link to add information to this solution:
I have a home built CNC running Mach 3. I have power to all the motors and the breakout board but no movement when running g-code. I cannot even manually move the motors with the arrow keys or page up and down. It also has an integrated 120v receptacle showing an open ground. I don't know if all this is related.

Cutting metal with lasers even at 100W and 130W is difficult. The main problem is molten is a byproduct of lasing, which can severely damage the laser.

Click the link to add information to this solution:
For the XL Vertical Laser Machine I see it won't cut metal as it is only 80w. However, I noticed that you are working on 100w and 130w versions so will that be sufficient to cut through sheet metal? If so, how much longer until those are available?

The greenBull kit (not the assembled) will need the table (the rails for the table is supplied), wires/cables for the stepper motors and stepper motor drivers, smaller gauge wires for digital wire connections (limit switches, drivers to control interface, etc), wires for the spindle connection to the VFD, tubing for water flow to and from the spindle, and a pump and reservoir (we are just about to introduce a small pump/reservoir/radiator/fan system for use with the spindle. The VFD/spindle, stepper motors/drivers and interface board are included.

Click the link to add information to this solution:
If I understand correctly, the greenBull kit comes with a spindle and laser. What else do I need to have a working machine. Obviously a table, do I also need the computer, software, wires, pump and plumbing, electronics, VFD, steppers and controllers?