Each home switch needs to be on a separate input on the Mach3 USB controller. For instance, the x-home on IN1, Y-home on IN2, and Z-home on IN3. You can still wire the other switches on the same input, for instance, the IN can contain the X-home and X++ limit. The X, Y, and Z homes can still serve as the limit --.

Additional Information:
So I need 3 of 4 INs only for the home switches??? The remaining one for ++? What about E-Stop and Probe?

Additional Information:
Please have a look at the wiring diagram you show below. There are all limit switches at IN2 and all home switches at IN3. Makes sense to me.

Click the link to add information to this solution:
[575] I have two limit switches for X, Y and Z axes connected to only one input terminal. As usual, I also want to use them as home switches. But after the first axis touches its home switch, I get an emergency stop because of "activating a limit switch". Mach 3 normally knows when to use a limit switch for homing. Which detail in the depths of Mach 3 did I forget?

No, you should not have received two parallel breakout boards in your CNC kit. You can return the extra item using standard shipping with COD. Our apologies for the confusion and the inconvenience.

I will answer the other question as another FAQ. Please check the Customer Service page to see the answer to that question.

If you have difficulty finding the answer, here is a link:
https://www.buildyourcnc.com/FAQ/13636

Click the link to add information to this solution:
I have a 2000 WK 11–3 Z limit switches going to A c10r10 breakout board . Can I also use them as my home position as well. I need The wiring configuration

For safety's sake I would recommend a new board because they are inexpensive compared to the electronics that they support. Alternatively, it's possible that the one dead pin is a simple fix, such as a bad connection or solder joint; if you feel comfortable making those repairs then it could be worthwhile to check. Finally, if you are not using all the input pins, you could continue to operate the limit switch on pin 11 and hope for the best.

Click the link to add information to this solution:
I have a breakout board and it appears that the pin 12 connection has failed: when i move my limit switches to pin 11 they work; they don't work on pin 12. Do i need a new breakout board?

No, you should not have received two parallel breakout boards in your CNC kit. You can return the extra item using standard shipping with COD. Our apologies for the confusion and the inconvenience.

I will answer the other question as another FAQ. Please check the Customer Service page to see the answer to that question.

If you have difficulty finding the answer, here is a link:
https://www.buildyourcnc.com/FAQ/13636

Click the link to add information to this solution:
I HAVE A 2000 WK 11–3 Z LIMIT SWITCHES GOING TO C10R10 BREAKOUT BOARD . CAN ALSO USE THEM AS MY HOME POSITION WELL. NEED THE WIRING CONFIGURATION

Did you set them up as limit switches or home switches?

Additional Information:
Not sure where do I check that?

Additional Information:
Go to config, then ports and pins, then input signals.

Additional Information:
The limits are labeled x++, x— for example.

Click the link to add information to this solution:
I'm using Mach3. I have 2 limit switches on X, 2 on Y and 1on Z for retracted/home. I can go to diagnostics and see the switches/inputs working. But when I move with jog or gcode they have no effect. Also I can go right past the soft limits. I must have something turn off but I don't know what.

Make sure to wire the limit as normally open.

Click the link to add information to this solution:
[575] I had limit switches working and on input 2. Now looking at Mach 3 diagnostics, Input 2 is continuously on and triggers limit stop. I removed all input 2 so the machine can run. Rebooted all. Anyway to reset Input on card?

You can put all of your limit switches (including the E-stop which serves the same purpose as the limit switches) and home switches on a single pin. When homing, mach3 will move the axis it wants to home, hit the switch, pull away from the switch, then move the next axis and repeat the steps for the next two axes.

The probe is on the 2nd pin. The SuperPID is on the 3rd pin and now you have another pin remaining.

The GND terminal can be doubled up.

Click the link to add information to this solution:
Additional to Question 3444: Additional Information: To Clarify: I need to set up 3 home switches which can double for limits (that's 3 pins.). Another pin for a probe. That's 4 pins used. Now I need to set up the other limit and E-stop switches. No pins left, how do I do that? Can a ground pin be doubled up on? Plus, I have a SuperPID. Another pin?

Are you trying to use the MPG (tab), or the keyboard for jogging the motors? You mention 0,0,0, are you trying to home the machine with the "ref all home"?

If you cannot move the motors with the keyboard, check if the jog is enabled.

Click the link to add information to this solution:
[596] I have my motors and limit switches working correctly but I am unable to get any movement from the 'jog step' so that I can set 0,0,0. What should I check

Absolutely! You can have almost unlimited limit switches and home switches on this controller. It all comes down to the wiring scheme used. I recommend the home switches be on separate input terminals. For example, IN1 would have the X home switch, IN2 would have the Y home switch and, IN3 would have the Z home switch if you plan on using home switches for the Z axis.

Adding the limit switches, these can be located on any input you want, even on the IN1, 2 or 3. The wiring scheme I like to use is as follows:
- IN1 has the X home, X limit ++, and X Limit --
- IN1 has the Y home, Y limit ++, and Y Limit --
- IN1 has the Z home, Z limit ++, and Z Limit --

In most cases, the Limit -- is the same switch as the Home switch.

These can be wired as NC (Normally closed) as a serial scheme, or as NO (Normally open) as a parallel scheme.

To understand the limits and wiring schemes, check out this video:

Click the link to add information to this solution:
[575] Hi, for the manage the limit switches, is it possible to have, for example, the same limit switch for X-- and X homing? And what is the configuration in mach3? In my CNC machine they are in the same position. Thank you

NC mechanical switch configuration is supported. You can download the manual from this page (Mach4 plugin and manuals):
https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

The pokeys57CNC controller has input terminals and pins for limit switches on each of the 8 axes. There are three separate inputs per axis, two for the actual limits of that axis, and one for the home position.

Connect each switch between the GND terminal and its respective axis limit terminal/pin. For instance, the limit switch will typically have three leads, COM, NC, and NO. In an NC configuration, the NC connects to the terminal/pin, say, Axis 1 lim +, and the COM connects to the GND terminal.

In Mach4, in the new device wizard, make sure to specify the correct option on the home and limit switches that matches the machine configuration.



Additional Information:
can you use one switch per axis for home only?

Click the link to add information to this solution:
Hello, I am trying to configure Home and Limit switches using the Pokeyes57cnc and NC switches. I am confused on the procedure of setting this up. wiring to the board and setting up in Mach4. Can you direct me to a tutorial or offer some suggestions? Thanks Dale

BYCNC Response:
This is correct. You will need to use a method appropriate for the software you are using. Also remember that NC switches are typically wired in series, while NO switches are normally wired in parallel.

User Response:
I am using the cnc planet software for your USB board. Are the limit configurations in this software?

BYCNC Response:
Yes, Planet CNC software is compatible with the use of limit switches. Configuration information will depend on your specific application. You can view Planet CNC's information here: http://www.planet-cnc.com/files/CNCUSBController.pdf

Click the link to add information to this solution:
LIMIT SWITCHES FOR AXIS. THE PRINT SHOWS THAT YOU CAN WIRE LIMITS EITHER N.O. OR N.C. SO IF THIS IS CORRECT I WOULD NEED TO TELL BOARD IN SOFTWARE HOW LOOK AT THESE LIMITS, I'M GOING GET AN INPUT LOOSE DEPEND ON IT.

We recommend using shield wire for wiring the limit switches.

Click the link to add information to this solution:
I recently wired my CNC machine with limit switches and tested them before mounting to the machine. They were configured and when tested worked great. After mounting them to the machine, they continued to register as triggered. The frame of the CNC machine is made of MDF so I don't think it is shorting off of the machine. Can you tell me what might be wrong?

Yes, the Mach3 USB board has two terminals that require 24V connection. Most VFDs have a 24V output that can be used to power this part of the Mach3 USB board.

The V+ and V- on the Mach3 USB is not absolutely necessary to operate the CNC machine/router. The V+ and V- of the Mach3 USB board powers the outputs, inputs, and spindle's speed and control.

Here is the Mach3 USB link for more information:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

The new YL600 VFD we have in stock may not have this 24V output. There is a 12V terminal, but I have not tested that terminal if it outputs 12V, or if it is a 12V input. If you are only conecting limit switches to the Mach3 USB and need to power that portion, 12V will be sufficient.

I will delve into these aspects in far more detail on video.

Thanks and Merry Christmas to you as well!

Click the link to add information to this solution:
Hey Guys, I have a brand new redleaf and 5x. In the final stages of wiring and wondering a few things. Can I connect the Mach3 USB board V+ V- to my frequency inverter (type YL600-2s-2k20)? If so where? Will your upcoming (part 2)video deal with this as well as final connections for limit switches and stop button? Merry Christmas!

Polabs prepared step by step user guide for PoKeys57CNC and Mach4 to try answering such questions. It is available in our downloads section: https://www.poscope.com/wp-content/uploads/downloads/Pokeys/LibrariesAndPlugins/Mach4 and PoKeys57CNC - step by step guide.pdf

Click the link to add information to this solution:
I need your assistance... I have two items left to setup on my Pokey57CNC and Mach4, Home switches and Spindle Speed. I have watched the videos, but they are for Mach3 and the screens are different in Mach4. Can someone please explain the setup of these two items in Mach4?

You can ask the question on this customer Service section. The questions on this section get answered immediately, or faster than our email service.

Click the link to add information to this solution:
I have received an email from you re my question Number 13956 and I want to make some inquiries re just the control board could you send me a email address as using the address that the email was sent to me keeps coming back.

You can add a limit switch to either the USB or the parallel board. Please refer to the product pages for these items to view wiring diagrams.

Click the link to add information to this solution:
I want to add limit switches but I have no connections on the breakout board. Can I use a usb interface board for the limit switches as well as the parallel port for the running?

You can add a limit switch to either the USB or the parallel board. Please refer to the product pages for these items to view wiring diagrams.

Click the link to add information to this solution:
I want to add limit switches but I have no connections on the breakout board. Can I use a usb interface board for the limit switches as well as the parallel port for the running?

Can you provide the model number of your VFD?

Yes, I have the "YL600 - 2S - 2K20"

It just came with a small booklet that is all in Chinese...

Click the link to add information to this solution:
I WIRED MY VFD (2.2KW VERSION) AND TRIED TEST RUNNING THE SPINDLE. CONFIGURED TO YOUR SPECS ON THIS WEBSITE, ONLY ISSUE IS WE GOT AN ERROR CODE. ERR 02, DO YOU KNOW WHAT IS? OR HAVE A LIST OF CODES? THANK

Yes, you can use 12VDC for the MAch3 USB controller at the 24V and DCM terminals. I have not tested using 12VDC in conjunction with the ACM and AVI terminals (PWM output) to control the spindle speed. PWM typically requires a reference voltage (from the VFD) and it's own voltage to produce the PWM signal. I am not sure if 12VDC is sufficient for the PWM. I have tested the inputs with 12VDC and they work fine.

Click the link to add information to this solution:
[575] does the 24VDC input actually need 24 VDC if only using the input for homing switches? Can you use 12 VDC? and would it be damaged with a higher voltage than 24 VDC?