[ Log In ]
[ Register ]

Question #: 13880

Question: How many sides does a square have?

Current Solution

A square has (4) four sides. The square also has sides of equal length. There are also 4 vertices and 4 inner angles measuring exactly 90 degrees (right angles).

Additional Information:
How many sides does a square have?

Additional Information:


Additional Information:
4


Additional Information:
4


Additional Information:
4

Additional Information:
6,5

Additional Information:


Additional Information:


Additional Information:

Respond:

Other Possible Solutions to this Question

  • HOW MANY SIDES DOES A TRIANGLE HAVE?

    The triangle has three (3) sides. The triangle is a polygon that contains three sides and three inner angles and three vertices.

    Additional Information:
    But if a triangle have a front and back side wouldn't the triangle have 5 sides

    Additional Information:
    Interesting slant (pun). A triangle would have 5 sides if the triangle had a thickness and became an object. A triangle drawn on paper with three lines would still only have three sides. A triangle is a primitive form of geometry (polygon) that can only have three sides in its simplest form. If you add complexity to the triangle with a thickness and count two more sides, then it really isn't the simplest form of the triangle anymore and it becomes another geometrical 3D primitive like a triangular prism.

    Additional Information:


    Additional Information:


    Additional Information:
    how many sides does a normal triangle have


    Additional Information:


    Additional Information:
    How many sides does a Triangle have?

    Additional Information:
    how many sided does a triangle have

    Additional Information:
    How many sides does a Triangle have

    Additional Information:


    Additional Information:


    Additional Information:
    How many a triangle has side

    Additional Information:
    How many a triangle has again

    Additional Information:
    How many sides does a triangle have

    Additional Information:
    A triangle has multiply answers for number of sides but is made up of 3 lines.. this is because when connecting the 3rd line to form the shape you create an "inside". so you could say a triangle has 2 sides, an "outside" and "inside" or you could say 4 sides, an "inside" and 3 "outside facings" or 6 sides 3 "outside facings" and 3 "inside facings". none of these answers are incorrect technically. the important thing is that a triangle is made up of 3 inner angles adding upto 180 degree's.

    Additional Information:
    how many sides of a triangle?

    Additional Information:
    Triangles have 3 sides. How many sides have 5 triangles

    Additional Information:
    How many sides does a Triangle have?

    Additional Information:
    How mony sides does a triangle have

    Additional Information:
    How mony sides does a triangle have

    Additional Information:
    How many sides does a Triangle have?

    Additional Information:
    15 sides
    in 5 triangles

    Additional Information:
    15 sides
    in 5 triangles

    Additional Information:
    15 sides
    in 5 triangles

    Additional Information:
    15 sides
    in 5 triangles

    Additional Information:
    15 sides
    in 5 triangles

    Additional Information:
    15 sides
    in 5 triangles

    Additional Information:
    15 sides
    in 5 triangles

    Additional Information:
    15 sides
    in 5 triangles

    Additional Information:
    15 sides
    in 5 triangles

    Additional Information:
    15 sides
    in 5 triangles

    Additional Information:
    15 sides
    in 5 triangles

    Additional Information:

    Click the link to respond:
    HOW MANY SIDES DOES A TRIANGLE HAVE?

  • HOW MANY SIDES DOES A TRIANGLE HAVE?

    The butterfly has 6 legs.

    Click the link to respond:
    HOW MANY SIDES DOES A TRIANGLE HAVE?

  • HOW MANY SIDES DOES A TRIANGLE HAVE?

    The violin has four strings.

    Additional Information:
    3

    Click the link to respond:
    HOW MANY SIDES DOES A TRIANGLE HAVE?

  • HOW MANY STRINGS DOES A VIOLIN HAVE?

    The violin has four strings.

    Additional Information:
    3

    Click the link to respond:
    HOW MANY STRINGS DOES A VIOLIN HAVE?

  • How many poles and pairs does your 2.5 KW spindle have?

    Our spindles are 2 pole, however we do not understand the "and pairs" portion of your question?

    Click the link to respond:
    How many poles and pairs does your 2.5 KW spindle have?

  • How much Z-axis travel does the 48x96 greenlean machine have?

    The greenLean Z-axis travel is about 4" - 5"-3/4".

    Click the link to respond:
    How much Z-axis travel does the 48x96 greenlean machine have?

  • HOW DO I MAKE MY MACHINE SQUARE?

    I use a standard large "L" square used in construction. I run gantry up and down with the bit along one side of the square to make the square aligned with the x-axis. I then run the bit along the other edge and if I see space from the edge of the bit to the square, I adjust the gantry square by loosening and tightening the eye bolts that hold the chain at the ends of the table. Repeat as necessary to get the desired square.

    Additional Information:

    Click the link to respond:
    HOW DO I MAKE MY MACHINE SQUARE?

  • IF MY COMPUTER DOESN'T HAVE A PARALLEL PORT, HOW DO I RUN THE MACHINE?

    If your computer does not have a parallel port, all you will need is a low cost PCI parallel adapter card (these can be found on amazon for $15-$20). If you plan on using a laptop (not recommended) you can try to find a PCMCIA parallel adapter, but many people have frequent issues with this setup. A more expensive solution would be to purchase a USB smooth stepper board. Unfortunately, we do not supply any of these adapters and cannot attest to their reliability.

    Additional Information:
    ur gay

    Additional Information:

    Click the link to respond:
    IF MY COMPUTER DOESN'T HAVE A PARALLEL PORT, HOW DO I RUN THE MACHINE?

  • HOW DO I SQUARE MY CNC MACHINE OR GANTRY?

    I use a standard large "L" square used in construction. I run gantry up and down with the bit along one side of the square to make the square aligned with the x-axis. I then run the bit along the other edge and if I see space from the edge of the bit to the square, I adjust the gantry square by loosening and tightening the eye bolts that hold the chain at the ends of the table. Repeat as necessary to get the desired square.

    Additional Information:

    Click the link to respond:
    HOW DO I SQUARE MY CNC MACHINE OR GANTRY?

  • hi. i need a 3/8 screw of 78 inches how much does it cost and do you have it?

    Our 3/8" lead screws are available at a maximum length of 72". A screw at that diameter is is not the best solution at long lengths for machines that will spin that axis quickly since there will be screw whipping.

    Click the link to respond:
    hi. i need a 3/8 screw of 78 inches how much does it cost and do you have it?

  • MY COMPUTER DOES NOT HAVE A PARALLEL PORT. HOW DO I INTERFACE WITH THE MACHINE?

    If your computer does not have a parallel port, all you will need is a low cost PCI parallel adapter card (these can be found on amazon for $15-$20). If you plan on using a laptop (not recommended) you can try to find a PCMCIA parallel adapter, but many people have frequent issues with this setup. A more expensive solution would be to purchase a USB smooth stepper board. Unfortunately, we do not supply any of these adapters and cannot attest to their reliability.

    Additional Information:
    ur gay

    Additional Information:

    Click the link to respond:
    MY COMPUTER DOES NOT HAVE A PARALLEL PORT. HOW DO I INTERFACE WITH THE MACHINE?

  • Does the laser XL have air assist?

    Yes, the vertical laser xl comes with a small air compressor that it typically used for air brush.

    Click the link to respond:
    Does the laser XL have air assist?

  • MY COMPUTER DOES NOT HAVE A PARALLEL PORT. HOW DO I INTERFACE WITH THE BREAKOUT BOARD?

    If your computer does not have a parallel port, all you will need is a low cost PCI parallel adapter card (these can be found on amazon for $15-$20). If you plan on using a laptop (not recommended) you can try to find a PCMCIA parallel adapter, but many people have frequent issues with this setup. A more expensive solution would be to purchase a USB smooth stepper board. Unfortunately, we do not supply any of these adapters and cannot attest to their reliability.

    Additional Information:
    ur gay

    Additional Information:

    Click the link to respond:
    MY COMPUTER DOES NOT HAVE A PARALLEL PORT. HOW DO I INTERFACE WITH THE BREAKOUT BOARD?

  • DO YOU HAVE BLACKTOE MACHINES WITH TABLES READY TO GO OR HOW LONG DOES IT TAKE MAKE ONE?

    Yes, we have the optional table for the blackToe, but we need to fabricate it, which only takes one day. We generally reserve one week for the total fabrication and packing of all parts.

    Click the link to respond:
    DO YOU HAVE BLACKTOE MACHINES WITH TABLES READY TO GO OR HOW LONG DOES IT TAKE MAKE ONE?

  • DO NEED TO SQUARE UP THE MACHINE AND IF SO YOU HAVE INSTRUCTIONS OR VIDEO FOR THIS?

    The eyebolts are used in the squaring of the machine. I would use a standard carpenters square and first run the end mill along the edge of the square to first make it parallel with the long axis. Then run the end mill along the other edge with the short axis and adjust the eye bolts and chain according to the angle that the machine is out of square.

    Click the link to respond:
    DO NEED TO SQUARE UP THE MACHINE AND IF SO YOU HAVE INSTRUCTIONS OR VIDEO FOR THIS?

  • HOW MANY AXES CAN MACH 3 CONTROL?

    Mach 3 CNC software can do the following:

    Converts a standard PC to a fully featured, 6-axis CNC controller
    Allows direct import of DXF, BMP, JPG, and HPGL files through LazyCam
    Visual Gcode display
    Generates Gcode via LazyCam or Wizards
    Fully customizable interface
    Customizable M-Codes and Macros using VBscript

    SET:

    Spindle Speed control
    Multiple relay control
    Manual pulse generation
    Video display of machine
    Touch screen ability
    Full screen eligibility

    EQUIPMENT:

    Lathes
    Mills
    Routers
    Lasers
    Plasma
    Engravers
    Gear cutting

    Additional Information:
    how to wire relay with mach board. I have mach interface board with one relay

    Click the link to respond:
    HOW MANY AXES CAN MACH 3 CONTROL?

  • How many revelolutions nema 23 425 oz

    The number of revolutions for a stepper motor is infinite as long as the stepper motor coils are being engaged by the driver and that the driver is being sent pulses and that the driver has sufficient power to engage the coils.

    With that said, all of our stepper motors have 200 steps per revolution, which may be the answer you may be seeking. The steps per revolution can be increased by microsteps using the driver. In some drivers, this can be as much as 256 microsteps which brings the steps per revolution to 51,200 steps.

    Click the link to respond:
    How many revelolutions nema 23 425 oz

  • I have a raid, how is it setup

    1) Make sure to setup Primary partition:

    Primary
    Beginning of this space
    Ext4
    Mount point: /
    and Swap partition:

    Logical
    Beginning of this space
    Swap area using "Something Else"

    2) get and install updates and upgrades

    sudo apt-get update
    sudo apt-get upgrade

    3) get raid software

    sudo apt-get update
    sudo apt-get install mdadm

    4) setup RAID

    a) if raids haven't been setup:
    sudo mdadm --create /dev/md0 --chunk=256 --level=0 --raid-devices=2 /dev/sda /dev/sdb

    b) if raids are setup, but just have to be reassembled:
    sudo mdadm --assemble /dev/md0 /dev/sda /dev/sdb

    or

    mdadm --assemble --scan

    Click the link to respond:
    I have a raid, how is it setup

  • HOW LONG DOES IT TAKE TO SHIP

    Unfortunately I am not able to give an estimate of shipping time. This is because there are multiple shipping options, Some of them cost more than others, but ensure the package arrives in a certain number of days. Others do not give a number of days, and many factors could change the length of shipping time, such as weather, or busy season. It would be best to choose an option you are comfortable with the price of, and then Google search the typical times it takes for that option to get to you, or call the shipping company and request that estimated time from them.

    Additional Information:

    Click the link to respond:
    HOW LONG DOES IT TAKE TO SHIP

Get Help with:
This Product
Orders
Tech Support
Sales
This Product
Order Query
Tech Support
Sales
Not logged in. Log In Register
Track Order(s)
View Order(s)
I Want to Schecule a One-On-One Paid Tech Support Session
Book an Appointment Pertaining to a BuildYourCNC Product (Free)
Ask a Quesion Below (Free):
Book an Appointment Pertaining Other Equipment ($60/half hour)
Book an Immedite Appointment Pertaining Other Equipment ($120/half hour)
Ask a Quesion Below (Free):
Waiting for response... I may not answer immediately, but I was notified on my cellular phone so my response is forthcoming. If I don't respond immediately, you can always go to the [My Account] page to see all of our chats at any time.