That is correct. To reverse the direction for a specific stepper motor on an axis, you should toggle the DirLowActive. The direction terminal on a driver (labeled Dir or CW) has a high signal for a particular direction and a low signal for the opposite direction. By simply toggling the DirLowActive, you are reversing this state.

Additional Information:
Also Check Homing/Limits there is also a reverse setting.

Click the link to add information to this solution:
Mach3 USB Interface Board, I cant reverse my axis direction by toggling Reversed in Motor Home/Softlimits, I have to toggle Dir LowActive in port & pins Motor Outputs to reverse an axis, any ideas?

It's generally acceptable to use one pin for all of your limit switches wired Normally Closed (NC), and another separate pin for a Z probe that is Normally Open (NO). LinuxCNC is quite flexible and allows for mixed configurations of NC and NO switches.

Just ensure you configure LinuxCNC correctly to recognize each pin's logic (Active low or active high). And perhaps run a few tests before running the machine.

Additional Information:
It's generally acceptable to use one pin for all of your limit switches wired Normally Closed (NC), and another separate pin for a Z probe that is Normally Open (NO). LinuxCNC is quite flexible and allows for mixed configurations of NC and NO switches.

Just ensure you configure LinuxCNC correctly to recognize each pin's logic (Active low or active high). And perhaps run a few tests before running the machine.

Click the link to add information to this solution:
[59] is it ok to use one pin for all of the limit switches wired NC and another pin for a z probe that is NO, or do all input pins need to be the same (NC or NO)? I would like to use LinuxCNC but will use Mach3 if necessary. a thanks!

Planet-CNC is the control software. If you decide to use the USB controller, you will need to use the planet-CNC software as the control software. You will be able to use any of the CAM software applications with the planet-CNC control software.

Click the link to add information to this solution:
Would I be able to use the Mach3 CNC Control Software or any of the CNC CAM Software(BOBCAD/CAM,CAMBAM) if I choose to use the Planet-CNC USB Interface Board?

Our MAch3 USB interface boards can be located here:

https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Click the link to add information to this solution:
I am interested in the 3 axis combo USB option. I notice you endorse the Planet-CNC for use with this but will Mach3 interface well with the USB beak out Board?

Yes, you can connect a THC, Torch Height Controller, with the Mach3 USB controller. The THC uses the inputs to determine if the z axis needs to move up or down according to the arc of the plasma torch. The THC connects its outputs to the inputs of the controller so the controller will be informed of the states of the plasma torch.

Click the link to add information to this solution:
I am interested in using the Mach3 USB interface board. I was wondering if there was a way to run a torch height controller with this board for use with a plasma cutter, and if so do you know of any THCs that will work. Thank you.

In our experience, the backlash compensation is not an ideal mechanism to solve backlash issues. It is best to resolve the backlash issue mechanically regather than through software.

Boards that handle all instructions on its own chip (which is the case for this all other USB boards) take some control away from Mach3. Without Mach3 having granular control. With that said, we do not have experience with the backlash compensation with that particular board. Our experience with backlash compensation with other boards have resulted in very poor accuracy and undesirable geometrical moves.

Additional Information:
zokkj

Additional Information:
zokkj

Additional Information:
zokkj

Additional Information:

Click the link to add information to this solution:
Mach3 USB Interface Board, Backlash Compensation in Mach3 is not working. Does this board support the backlash function?

If the outputs are not functioning as expected on the Mach3 USB controller, confirm that the port for the output is 3. This is a part of the configuration I did not show on the video I created on using the outputs for the RNRMotion controller.

Additional Information:
Thanks for your help. Under Ports & Pins>Output Signals I show Output#1 through Output#4 as Enabled. All have Port# set to 3. Pin Numbers for each Output# are same as Output# (Output#1 set to Pin Number 1, etc.).
Still no voltage showing on output 1 (of the board) when I input M3 in the Input section of the MDI tab. However if (in Spindle Setup tab) I set (in "Relay Control")M3 Output# to 3 and M4 Output# to 4 things work as expected. Is it possible to have the M3 signal show up on Output#1?
Thanks again.

Additional Information:

Click the link to add information to this solution:
Mach3 USB interface board initial setup. Following instructions in the video "Mach3 USB controller outputs". Arrow keys cause red LED to blink, but cannot duplicate 24V output with M3 (or M4) commands as shown in the video. Do I need to re-install Mach3?

Our MAch3 USB interface boards can be located here:

https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Click the link to add information to this solution:
I AM INTERESTED IN THE 3 AXIS COMBO USB OPTION. NOTICE YOU ENDORSE PLANET-CNC FOR USE WITH THIS BUT WILL MACH3 INTERFACE WELL BEAK OUT BOARD?

I would suggest using the NPN proximity sensor for the Mach3 USB or the Pokeys57cnc. The proximity sensors have a top DC voltage limit of 30 volts, so it would be best to use the 24V power supply that is used to power the controller. Both controllers have a 24V power requirement, so that is convenient.

The blue wire of the proximity sensor is the GND wire and is connected to the 24V power supply's V- terminal. The brown wire is the positive wire and is connected to the V+ terminal of the 24V power supply. The black wire is the signal wire and is connected to the input terminal of the controller.

Click the link to add information to this solution:
if I wanted to use your inductive proximity sensor's with your USB interface board what would I need besides the sensors I would be using 5 of the sensors.

The Mach3 USB interface board requires 24V relays externally. There are no relays on the mach3 usb board. If you use an external relay on the mach3 usb board, the relay connects to the V+ which is 24V and the output pin is the return.

Additional Information:
I understand what you are saying. Does your relay board work with the Mach3 USB board? If not, what relay board do you suggest to work with this usb controller?

Additional Information:
Our relay board works with our parallel breakout board. An off the shelf SSR (Solid State Relay) made for 24V should work fine.

Click the link to add information to this solution:
I have your Mach3 usb interface board and am interested in the relay board to turn plasma torch on/off. I have a different relay board that doesn't work, it needs 0/5v from output pin to trigger and the usb board doesn't put out 5 volts. Does this relay board need 5v on output or will work fine with this usb controller?

When dealing with 3rd party machines, we have a universal setup that will fit almost any other machine, although please take in consideration the specifications in which your stepper motors and drivers are used and set to!
Now changing the controls, would be more or less changing the Breakout board/interface board to a different one that might use a different program to run your machine. Usually you will not need to change your interface board or breakout board, unless the 3rd party manufacture made it specifically to that set up.

Click the link to add information to this solution:
I purchased a 3040 CNC router off eBay a year ago and would like to change the controls. The steppers are 185oz.in motors. My question do i need to purchase a interface board and break out boards?

You can use our shopping cart to determine the shipping. Add the machine and the parts you want to purchase, enter your shipping address and click on the Calculate Shipping Button to get a price for shipping. The shipping charges are determined directly from the carriers at the time of pressing that button.

Additional Information:


Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
Hi i am interested in the greenBull 6x with Hybrid Laser/Spindle Head (includes Spindle/VFD and Laser Components) - USB Interface (Long Z). I was wondering how much it would cost to get this machine to NZ?

The Mach3 USB interface card uses 5V (powered from the computer's USB) and a 24v to power the inputs, outputs and spindle control

the mach3 usb interface can be found here:

https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

But the mach3 usb does not absolutely need the 24V supply. The 24v supply is only needed if you will be using limit switches (I1-4), VFD controlled automatically and for use with the outputs (O1-4)


Additional Information:
The 36v 8.8 amp power supply we typically recommend is for powering the stepper motor drivers.

Click the link to add information to this solution:
The electronics for my current cnc machine has a 36v 8.8 amp power supply. Is this power supply sufficient to power my new Mach3 USB interface?

I would suggest using the NPN proximity sensor for the Mach3 USB or the Pokeys57cnc. The proximity sensors have a top DC voltage limit of 30 volts, so it would be best to use the 24V power supply that is used to power the controller. Both controllers have a 24V power requirement, so that is convenient.

The blue wire of the proximity sensor is the GND wire and is connected to the 24V power supply's V- terminal. The brown wire is the positive wire and is connected to the V+ terminal of the 24V power supply. The black wire is the signal wire and is connected to the input terminal of the controller.

Click the link to add information to this solution:
Good evening, if I wanted to use your inductive proximity sensor's with your USB interface board what would I need besides the sensors I would be using 5 of the sensors. I have a 48V 12amp power supply. Thank you

The parallel breakout board allows for 4 input connections. Each input connection can have an unlimited number of switches, but if you need to separate the switch circuit for, say, all of the home switches, you can use another input pin. There is no need to add another breakout board to add more switches unless you need to use the input pins for totally unique conditions that may or may not be related to CNC functions.

Customer response:
To Clarify: I need to set up 3 home switches which can double for limits (that's 3 pins.). Another pin for a probe. That's 4 pins used. Now I need to set up the other limit and E-stop switches. No pins left, how do I do that? Can a ground pin be doubled up on?

Plus, I have a SuperPID. Another pin?

Additional answer:
You can put all of your limit switches (including the E-stop which serves the same purpose as the limit switches) and home switches on a single pin. When homing, mach3 will move the axis it wants to home, hit the switch, pull away from the switch, then move the next axis and repeat the steps for the next two axes.

The probe is on the 2nd pin. The SuperPID is on the 3rd pin and now you have another pin remaining.

The GND terminal can be doubled up.

Additional Information:
how about a diagram to reference showing the pin-out to use

Here is the diagram for the parallel breakout board (pins 10 through 13 are used for input):

The circuit is from the GND to the input

Here is the diagram for the Mach3 USB board (pins I1 through I4 are used for input):
https://www.buildyourcnc.com/Documents/Electric%20Wiring%20Diagram.pdf
The circuit is from the V- to the input pin

Click the link to add information to this solution:
Limit, E-stop and home switches: To set up the maximum number of switches set up I would need 2 BOB's, correct? How is this implimented and wired?

Yes, you can use a laptop if you have a controller that uses a USB, like the Mach3 USB card. If you don't have that, you can purchase that part here:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

If you have a controller board that connects to a 25 pin connector, modern laptops will not be able to connect to that port.

How old is your CNC computer system?

Additional Information:
The CNC computer system is 2013 (5 years). The built in video card went out. I will order the Mach3 USB card. Thank you.

Additional Information:
You're welcome

Click the link to add information to this solution:
The motherboard on the computer I bought from you went out. What would you suggest. I have a laptop, could I use it and use a Mach3 USB interface board?

Yes, Mach3 (the software profram) will work with Windows 7, and windows 10 when coupled with the Mach3 USB interface. If you intend to use the parallel port driver, stick with Windows 7 in 32-bit mode.

Additional Information:
Rnrmotion.dll is a dynamic link library which is very similar in function to an executable program, or app. Since a dll is executable, malicious code can be embedded in that type of file, so windows will automatically flag all files of this type. You just need to make sure you are downloading from a trusted source. The emotion.dll file on our site is clean, but still run run windows defender against it to make sure.

Additional Information:

Click the link to add information to this solution:
I intend to intall mach3 on Windows 10 OS. Will I need to install the USB Motion Driver RnRMotion.dll? I attempted to download this but it was blocked by Windows 10.

Ok. Email me at customerservice@buildyourcnc.com to setup the return.

Thanks.

Click the link to add information to this solution:
I would like to return the Mach3 USB CNC Interface I just received. I am not continuing the project requiring it.

We do have a relay board that words like a standard relay.

Here is the URL of the relay board that we offer:

https://www.buildyourcnc.com/item/electronicsAndMotors-breakout-Relays-relay-board-250V-12A-5V

Click the link to add information to this solution:
I have your mach3 USB BoB, do you guys sell a torch control relay I can wire up to turn my plasma torch on and off and how I would wife that too this BoB?