When you power up your VFD, you can go into the programming mode by pressing the program button. You can press the up and down arrows to move through the parameters. Press the set button to go into the parameter to see the value of that parameter. If you want to make changes to that parameter, change the value with the up and down arrows until the desired value is shown, and press the set button to accept the changes.

Click the link to add information to this solution:
[77] I am having troubles finding the PD program, I have the Pd but it doesn't show everything I need to program my VFD. Any help will be appreciated...

The 12V power supply has 3 terminals for AC in: N, L and earth ground. The output of the 12V power supply has 2 DC + and - terminals. Cut the connectors off of the ends of the fan and pump wires. Strip the red and black wires of both units. The fan will connect to the 12V power supply red to the + and black to the -. The pump will connect in the same way, but the white is not connected.

If you have a pump that has a grey and black wire on the large connector, the grey is the 12VDC V+ wire and the black wire goes to the V-. The extra wire does not need to be connected.

Click the link to add information to this solution:
THE GANTRY MOUNTED SPINDLE WATER COOLER PUMP THAT I PURCHASED DOES NOT OPERATE NO MATTER HOW CONNECT THREE WIRES TO TWO WIRE POWER SUPPLY.

You will need the following:
- router/spindle for the machine
- computer to control the machine
- construct a table if the optional table is not purchased
- wire and cable to connect all of the electronics

Additional Information:
- software to run the gcode (purchased separately)

Click the link to add information to this solution:
DOES THE PRICE OF 2’ X 4’ ROUTER INCLUDE EVERYTHING WOULD NEED TO START ROUTING?

If one or more motor is not responding, please follow the troubleshooting directions below:

For parallel Bob only! Make sure both the parallel and USB are connected.

Re-check wiring, and connections for continuity (no breaks in the wires) and check for correct wiring locations from driver to BoB.
Check dip switch settings on the driver.
Check components, by swapping the motors (ex. y-axis motor to z or x-axis driver and z or x-axis motor to y-axis driver) to check if motor functions on another driver.
Depending on software check step low active (mach 3) or invert pulse (planet-cnc) for the axis which is not responding.
Mach 3 - config/port & pins/motor outputs / Planet-CNC - file/settings/axes

Click the link to add information to this solution:
I have an engine NEMA 34 from Y axis on my green bull that do not response, I already check connections and everything seems to be OK, how can I check that the motor it's working properly or not?

In our 3-Axis electronics kit, the power supply's provided are capable of both 110V-220V. You have the capability to switch between both in case you might decide to run 220v in the near future or will relocate where 110v is being used.

Additional Information:
Connect spindle to the board



Additional Information:



Additional Information:

Click the link to add information to this solution:
In the 3 Axis Electronics Combo, what is the AC input of the power supply (110v or 220v??). is it possible to specify a certain voltage when ordering?

Only the 110v Version will have any indication of voltage on it. On the side of the power supply unit that has the black terminal strip and red wire coming out of it, there will be a silver sticker on the white side of the transformer that will state 110v, if it is 110v. If there is no sticker, then it should be 220v.

Additional Information:
20

Click the link to add information to this solution:
How can i tell if my laser supply is 110 or 230 VAC? there is no marking of any kind

In our 3-Axis electronics kit, the power supply's provided are capable of both 110V-220V. You have the capability to switch between both in case you might decide to run 220v in the near future or will relocate where 110v is being used.

Additional Information:
Connect spindle to the board



Additional Information:



Additional Information:

Click the link to add information to this solution:
Does the power supply in the "3 Axis Electronics Combo (Small Motors)" have a 220V input option?

LaserCad-->File-->Factory Manage-->608111-->>Permanent right to use-->Set

Additional Information:


Additional Information:
Not Working With Trocen awc7813

Additional Information:

Click the link to add information to this solution:
How to unlock the AWC708C system, the driver's screen says the system is locked

The formula for finding the steps per mm is found in the units itself. First, you mentioned that the motor is a servo. This needs to be clarified as a servo is different than a stepper motor. Some servos behave similar to a stepper motor, so I will continue with this in mind.

The formula is (steps/mm):

You need to find the steps. The stepper motor has a natural number of steps per a full revolution. This is typically 200 steps per revolution.

The driver for the stepper motor allows you to increase the number of steps per revolution by adding a specified number of steps between each step. For instance, if you set the driver to 1/4 microstepping, then instead of having 200 steps per revolution, you would have 200 x 4 = 800 steps per revolution.

So now we have the first part of the formula:

Steps / mm = (200 x 4) / mm

Lets determine the mm side of the formula:

You mention that the pitch is 0.5 mm. Check to insure that the lead is also 0.5 mm. This could be a multiple start lead screw where the pitch is different than the turns per mm. If in this case, that the 0.5 mm is the travel for one full revolution, then you can simply plug this into the formula as:

mm = .5 mm

Otherwise, determine how fat the travel is for one complete revolution.

Therefor, with what we know and the driver is set at 1/4 microstepping and the stepper motor has a natural step count per revolution at 200:

steps / mm = (200 steps x 4) / 0.5 mm = 800 steps / 0.5 mm = 1600 steps / mm

If your travel for one revolution is not 0.5 mm, then plug in your travel distance instead.



Additional Information:
i know about steps/mm calculation for stepper motor, because i am using servo motor that why i asked about that. please tell for servo motor.

Additional Information:
because its my first time with servo motor i have no idea about calculation of parameter with servo.

Additional Information:
Have you attempted to contact the manufacturer or seller of the servo? We typically respond to customers of our products on this customer service area, unless we have extensive knowledge of the subject and can answer the question efficiently.

Additional Information:

Click the link to add information to this solution:
hello there, i am using servo motor for my X and Y Axis but i dont know how to calculate steps/mm for that, the lead screw i am using is have pitch of .5 mm. please helpme on this i have done everything only this point is pending.

Our CNC machines can be lengthened to work with our customers specific projects.

For a 3.5' x 14' cutting surface, I would recommend our greenBull 4X! (4'x8'). You will only need to add the remaining length of rail(4) and chain(2) to accommodate the additional 6Ft, so this machine will have a cutting surface of 4' x 14'.

The additional lengths for the x-axis travel will be a total of 28Ft, and 14Ft of chain. We recommend selecting all the items you wish to purchase and see the actual total in your cart.

Click the link to add information to this solution:
I HAVE INTEREST IN SOME KIT AROUND 14' X 3.5' CAN YOU SUPPLY? ALREADY PRICE? AND WHAT MORE NEED?, MY IS MODELING KAYAKS CNC

That shouldn't be a problem. I will need the current rating for the motors. We can subtract the price of the motors. and you can add you own. If you want us to solder the cable to the round connectors and them motor, you would need to send the motors to us.

Let me know and I can send a paypal invoice for the redLeaf without motors.

Click the link to add information to this solution:
DON'T WANT TO USE MY OWN MOTORS FOR THE REDLEAF CNC COMPUTER SYSTEM.

Yes, the 651 oz/in motor requires a driver that is compatible to the motors (the motor will draw 6 amps max and the driver paired with this motor will be able to allow for a 6 amp draw). I would also recommend a 36 volt power supply for better high velocity performance.

Click the link to add information to this solution:
I HAVE ONE OF YOUR SMALLER STEPPER MOTORS RUNNING MY X AXIS BRIDGE CRANE AND IF IT IS MOVED TO FAST THE MOTOR SOUNDS LIKE SKIPPING STEPS WILL 651OZ REQUIRE A DIFFERENT POWER SUPPLY CONTROLER?

Thanks for your interest in the 80 Watt Laser Tube Power Supply. We will start offering the 220 Volt version of these power supplies on September 23rd.

Additional Information:

Click the link to add information to this solution:
I was looking for a MYJG80W power supply but I see you may not have the 220 volt version. Do you have these as yet and if not what can you advise on availability or where I may find one...Thanks

If you are using a spindle with a VFD, there is a 24 volt power supply that will provide the correct power for the V+ and V- on the Mach3 USB. The 12V option is only if you are using the limit switches on that side of the board, but if you are using it to control spindle speed and for the outputs, it's best to use a 24V power supply, or the 24V output on the VFD.

Additional Information:
Closed loop

Additional Information:
Can i use 12v in the 24v input

Click the link to add information to this solution:
The Mach 3 usb board requires an additional 12V power supply. How many amps would you recommend? Would a 1A wall adapter suffice.

That depends on a few factors. In most cases, three 3.0 amp motors and drivers will not exceed 8.8 amps of available current. All of the motors would need to be at full torque to reach the 9 amps (3x3). This depends on the mechanical method you are using for each motor, and how you are using the machine. In most cases, only two motors are moving at a time (i.e. 3D carving where the X and Z are moving simultaneously and the y only moves to go to the next row). In traditional cutting profiles, only the x and y are moving simultaneously and the z-axis moves at the location it needs to start cutting the next layer.

With that said, it is ok to add an extra power supply if you feel you need more available current.

Click the link to add information to this solution:
[51] Would the single 8.8A power supply be undersized for 3 6.0A Drivers? would you recommend getting another PS?

This video will illustrate how to test for laser power:

Click the link to add information to this solution:
HOW TO KNOW IF THE POWER SUPPLY OF THE LASER TUBE IS DAMAGED

It is not necessary to connect the spindle VFD (Variable Frequency Drive also called an Inverter) to the computer or CNC motion electronics. The VFD can be controlled independently using the control panel on the VFD. The control panel has the ability to control all aspects of the spindle including Speed, Torque, limits, etc. However, you can connect the VFD to the computer so the CNC control program can control the spindle during the CNC Machine operation. You will need to connect the VFD to the computer via a serial conection (in this case, it is the RS-485 protocol).

The following are instructions on how to connect the VFD to Mach3 via this RS-485 serial connection.

The first thing you will need is the dynamic link library to pair with mach3 called the Huanyang VFD Mach3 PlugIn. You can find this file at the mach3 support forum here: http://www.machsupport.com/forum/index.php/topic,14182.0.html

You will also need to download the Microsoft .net 3.5 framework and install it: https://www.microsoft.com/en-us/download/details.aspx?id=21

Follow the pdf that comes with the library file, but here is a synopsis of what you need to do (I also added a lot more information that may be useful during this process as the manual does not cover the main connections that need to be done):

You will need to program your VFD so that it knows how to communicate with mach3 and the computer (go into the programming mode of the VFD and change these parameters):
- PD001 - value 2 - Enables with communication aspect of the VFD
- PD002 - value 2 - Enables frequency control from the communcations port
- PD163 - value 1 - VFD address
- PD164 - value 1 - Baud rate of 9600 (speed of the communication)
- PD165 - value 3 - 8N1 RTU - 8 bits (that's the size of the word that gets communicated), N (No parity or no error checking) and 1 (1 stop bit)

Copy the dll file to the PlugIns folder of mach3.

Connect the RX and TX lines to your computer. There are a couple ways you can do this, but the recommended way would be to use an FTDI USB device which converts a USB to a serial com port. The device will have Rx and Tx connectors to connect to the VFD terminals with the same labels. This method is recommended since serial ports are not as common in computers these days.

Next, you will need to configure mach3 to use the plugin library. Start mach3 and click on Menu -> config ->Config Plugins. Enable the new plugin by clicking on the red cross on the left column next to the plug in. Restart mach3 after doing this.

No you need to configure mach3 to use the HuanyangVFD plugin. Go to the ports & pins configuration and select the spindle setup tab. Make sure that the Disable Spindle Relays checkbox is unchecked. We don't want mach3 to output a signal for a relay since the spindle will start up and turn off within the VFD and not from an external relay.

Next, go to the HuanyangVFD settings by clicking on Menu -> plugin control -> HuanyangVFD. Set the parameters to the same settings you put into the VFD programming. The com port will be shown as new hardward when you plug in the USB FTDI device. A little bubble will be displayed at the bottom right where it will notify you that a new device is being installed (be patient while windows assigns a com port). Alternatively, you can use the windows device manager to see which port was set for the new USB FTDI device). You may need to restart mach3 several times until you get the correct information displayed in the PD001 and PD002 fields. When the com port is correct and the other parameters, like baud and VFD address is the same as you entered in the programming, then the PD001 and PD002 will show the number 2, otherwise, a 99 will appear which means that communication was not successful.

You can now control the on/off and RPM of the spindle using the RS485 communication between mach3 and the VFD.

Additional Information:
The question was how to connect the spindle to the redfy. I did not receive a VFD.
I have the redFly system and a 2.2kW Spindle - 110V how do i connect the spindle?

Additional Information:
If you received a spindle without a VFD, please contact us asap. Our spindle will not work without a VFD.

Additional Information:
Hi, how is this setup in mach4?

Click the link to add information to this solution:
I HAVE THE REDFLY SYSTEM AND A 2.2KW SPINDLE - 110V HOW DO CONNECT SPINDAL?

The best wiring diagram that can be used for the redLeaf and redSprout CNC computer system would be found on instruction #1 (datasheet for the breakout board) on this page: https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

Click the link to add information to this solution:
Hi I live in South Africa and want to know if i can buy a wiring and component diagram for the readleaf plug and play computer system?

The best wiring diagram that can be used for the redLeaf and redSprout CNC computer system would be found on instruction #1 (datasheet for the breakout board) on this page: https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

Click the link to add information to this solution:
Hi I live in South Africa and want to know if i can buy a wiring and component diagram for the readleaf plug and play computer system?