It is not necessary to connect the spindle VFD (Variable Frequency Drive also called an Inverter) to the computer or CNC motion electronics. The VFD can be controlled independently using the control panel on the VFD. The control panel has the ability to control all aspects of the spindle including Speed, Torque, limits, etc. However, you can connect the VFD to the computer so the CNC control program can control the spindle during the CNC Machine operation. You will need to connect the VFD to the computer via a serial conection (in this case, it is the RS-485 protocol).

The following are instructions on how to connect the VFD to Mach3 via this RS-485 serial connection.

The first thing you will need is the dynamic link library to pair with mach3 called the Huanyang VFD Mach3 PlugIn. You can find this file at the mach3 support forum here: http://www.machsupport.com/forum/index.php/topic,14182.0.html

You will also need to download the Microsoft .net 3.5 framework and install it: https://www.microsoft.com/en-us/download/details.aspx?id=21

Follow the pdf that comes with the library file, but here is a synopsis of what you need to do (I also added a lot more information that may be useful during this process as the manual does not cover the main connections that need to be done):

You will need to program your VFD so that it knows how to communicate with mach3 and the computer (go into the programming mode of the VFD and change these parameters):
- PD001 - value 2 - Enables with communication aspect of the VFD
- PD002 - value 2 - Enables frequency control from the communcations port
- PD163 - value 1 - VFD address
- PD164 - value 1 - Baud rate of 9600 (speed of the communication)
- PD165 - value 3 - 8N1 RTU - 8 bits (that's the size of the word that gets communicated), N (No parity or no error checking) and 1 (1 stop bit)

Copy the dll file to the PlugIns folder of mach3.

Connect the RX and TX lines to your computer. There are a couple ways you can do this, but the recommended way would be to use an FTDI USB device which converts a USB to a serial com port. The device will have Rx and Tx connectors to connect to the VFD terminals with the same labels. This method is recommended since serial ports are not as common in computers these days.

Next, you will need to configure mach3 to use the plugin library. Start mach3 and click on Menu -> config ->Config Plugins. Enable the new plugin by clicking on the red cross on the left column next to the plug in. Restart mach3 after doing this.

No you need to configure mach3 to use the HuanyangVFD plugin. Go to the ports & pins configuration and select the spindle setup tab. Make sure that the Disable Spindle Relays checkbox is unchecked. We don't want mach3 to output a signal for a relay since the spindle will start up and turn off within the VFD and not from an external relay.

Next, go to the HuanyangVFD settings by clicking on Menu -> plugin control -> HuanyangVFD. Set the parameters to the same settings you put into the VFD programming. The com port will be shown as new hardward when you plug in the USB FTDI device. A little bubble will be displayed at the bottom right where it will notify you that a new device is being installed (be patient while windows assigns a com port). Alternatively, you can use the windows device manager to see which port was set for the new USB FTDI device). You may need to restart mach3 several times until you get the correct information displayed in the PD001 and PD002 fields. When the com port is correct and the other parameters, like baud and VFD address is the same as you entered in the programming, then the PD001 and PD002 will show the number 2, otherwise, a 99 will appear which means that communication was not successful.

You can now control the on/off and RPM of the spindle using the RS485 communication between mach3 and the VFD.

Additional Information:
The question was how to connect the spindle to the redfy. I did not receive a VFD.
I have the redFly system and a 2.2kW Spindle - 110V how do i connect the spindle?

Additional Information:
If you received a spindle without a VFD, please contact us asap. Our spindle will not work without a VFD.

Additional Information:
Hi, how is this setup in mach4?

Click the link to add information to this solution:
I HAVE THE REDFLY SYSTEM AND A 2.2KW SPINDLE - 110V HOW DO CONNECT SPINDAL?

That shouldn't be a problem. I will need the current rating for the motors. We can subtract the price of the motors. and you can add you own. If you want us to solder the cable to the round connectors and them motor, you would need to send the motors to us.

Let me know and I can send a paypal invoice for the redLeaf without motors.

Click the link to add information to this solution:
DON'T WANT TO USE MY OWN MOTORS FOR THE REDLEAF CNC COMPUTER SYSTEM.

The password is: 608

Click the link to add information to this solution:
WHAT IS THE SYSTEM PASSWORD FOR LASER CONTROL UNIT?

Check step 9 on this page: http://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

Click the link to add information to this solution:
IF YOU HAVE CIRCUIT (OR PICTURE) OF HOW THIS RELAY IS CONNECTED TO THE ROUTER

This video will illustrate how to test for laser power:

Click the link to add information to this solution:
HOW TO KNOW IF THE POWER SUPPLY OF THE LASER TUBE IS DAMAGED

The blackTooth Laser cutter and Engraver can be built in a weekend. Take a look at the build instructions and try to determine if you feel you have sufficient capability to put together the laser system.

Click the link to add information to this solution:
HOW DIFFICULT IS IT TO BUILD THE BLACKTOOTH LASER CUTTER?

Yes, it is found in laser components section

Click the link to add information to this solution:
DO YOU GUYS SELL THE POTENTIOMETER FOR YOUR LASER SYSTEM BY ITSELF

The blackTooth Laser cutter and Engraver can be built in a weekend. Take a look at the build instructions and try to determine if you feel you have sufficient capability to put together the laser system.

Click the link to add information to this solution:
HOW DIFFICULT IS IT TO BUILD THE BLACKTOOTH

The parallel breakout board has a relay that can turn the router on and off according to the control software in the computer. The router will turn on automatically prior to the machine moving (a time frame can be set so the router is up to speed). When the machine is finished and is not moving, the router automatically turns off. This is with the m3, m4, and m5 codes in the g-code.

If you are interested in the USB breakout board, you will need to get an independent relay board.

Click the link to add information to this solution:
HOW THE ROUTER IS CONNECTED TO ELECTRONICS?

The parallel breakout board has a relay that can turn the router on and off according to the control software in the computer. The router will turn on automatically prior to the machine moving (a time frame can be set so the router is up to speed). When the machine is finished and is not moving, the router automatically turns off. This is with the m3, m4, and m5 codes in the g-code.

If you are interested in the USB breakout board, you will need to get an independent relay board.

Click the link to add information to this solution:
HOW IS THE ROUTER CONNECTED TO ELECTRONICS?

The blackTooth Laser cutter and Engraver can be built in a weekend. Take a look at the build instructions and try to determine if you feel you have sufficient capability to put together the laser system.

Click the link to add information to this solution:
HOW COMPLEX IS YOUR KIT TO ASSEMBLE, AND MOST IMPORTANTLY - HARD IT SETUP CONTROL THE LASER WITH MACH3?

The greenlean requires 56 feet of 1/4 Inside Diameter and 3/8 Outside Diameter silicon tube for the spindle.

Additional Information:
20

Additional Information:
20

Click the link to add information to this solution:
HOW MUCH SILICONE TUBE DO I NEED FOR A GREEN LEAN TO CONNECT THE SPINDLE

The parallel breakout board has a relay that can turn the router on and off according to the control software in the computer. The router will turn on automatically prior to the machine moving (a time frame can be set so the router is up to speed). When the machine is finished and is not moving, the router automatically turns off. This is with the m3, m4, and m5 codes in the g-code.

If you are interested in the USB breakout board, you will need to get an independent relay board.

Click the link to add information to this solution:
HOW CAN THE ROUTER BE CONTROLLED OR CONNECTED TO ELECTRONICS COMPUTER?

blackToe requires a minimum cable length of of 15 ft for X, 17 ft for Y and 18 ft for Z for the redLeaf to be positioned at midpoint along the long axis and under the table. Each axis would need have 6 feet extra (form the midpoint)

Click the link to add information to this solution:
IF WE ASSUME DESIRE TO PLACE THE RED LEAF 6' AWAY FROM TABLE, HOW MUCH CABLE IS NEEDED CONNECT MOTORS ON TABLE ITSELF?

The instructions on how to do this are found here, in these two videos, http://buildyourcnc.com/PrimeronHomingandLimitSwitches.aspx

Additional Information:

Click the link to add information to this solution:
HOW DO I CONNECT A TOUCH PLATE TO THE BREAKOUT BOARD?

If you select the Settings Page and select or tick Auto Limit Override - this will allow you to back off the switch.

Additional Information:
limit and home switch

Click the link to add information to this solution:
IS THERE A WAY TO GET RID OF THE PARALLEL CABLE AND SOMEHOW USE USB ?

The formula and calculation is a starting point to get into the area of steps per inch. You will then need to use the mach3 calibration utility to get the exact steps per inch.

Formula:
step per inch = (motor steps * microstepping) / (travel at one turn of the motor in inches)
if microstepping is set at 16 (1/16 on the driver) then and you are using a sprocket and chain with a pitch of .25 inches and 12 teeth on the drive sprocket
= (200 * 16) / (12 * .25)
= 3200 / 3
= 1066.666 steps per inch

For lead screw that has a travel of .5 inches at one turn like the 5 start 1/2 inch lead screw and using 4 microsteps per step (1/4):
= (200 * 4) / (.5)
= 800 / .5
= 1600 steps per inch

Remember to use the mach3 calibration wizard and double check the driver microstep setting.

Additional Information:


Additional Information:


Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:
SrCyFFpZ

Additional Information:
-1 OR 2+902-902-1=0+0+0+1 --

Additional Information:
-1 OR 2+722-722-1=0+0+0+1

Additional Information:
-1' OR 2+275-275-1=0+0+0+1 --

Additional Information:
-1' OR 2+345-345-1=0+0+0+1 or '6eaEcsTN'='

Additional Information:
-1" OR 2+474-474-1=0+0+0+1 --

Additional Information:
1'"

Additional Information:
1����%2527%2522

Additional Information:
@@E5bKt

Additional Information:
1'"

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
WHAT IS THE FORMULA TO DETERMINE STEPS PER INCH OR RESOLUTION FOR EACH AXIS?

Yes, you can use a touch probe with our machines as it is really independent of the machine structure, mechanical components and motion electronics, for the most part. We don't currently sell touch probes, however, but standard touch probes for CNC machines will work fine.

Click the link to add information to this solution:
the bluechik - IS there a 3D Touch Scanning to scan in present made items ?

Three 24" x 48" sheets of mdf is used for the book build or the combo #1 plans and kit.

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:
nt9ZbSRf

Additional Information:
-1 OR 2+534-534-1=0+0+0+1 --

Additional Information:
-1 OR 2+83-83-1=0+0+0+1

Additional Information:
-1' OR 2+658-658-1=0+0+0+1 --

Additional Information:
-1' OR 2+552-552-1=0+0+0+1 or '8QfEjrbS'='

Additional Information:
-1" OR 2+524-524-1=0+0+0+1 --

Additional Information:
if(now()=sysdate(),sleep(15),0)

Additional Information:
0'XOR(if(now()=sysdate(),sleep(15),0))XOR'Z

Additional Information:
0"XOR(if(now()=sysdate(),sleep(15),0))XOR"Z

Additional Information:
(select(0)from(select(sleep(15)))v)/*'+(select(0)from(select(sleep(15)))v)+'"+(select(0)from(select(sleep(15)))v)+"*/

Additional Information:
-1; waitfor delay '0:0:15' --

Additional Information:
-1); waitfor delay '0:0:15' --

Additional Information:
-1)); waitfor delay '0:0:15' --

Additional Information:
1 waitfor delay '0:0:15' --

Additional Information:
MXjE3Md3'; waitfor delay '0:0:15' --

Additional Information:
gont9Py6'); waitfor delay '0:0:15' --

Additional Information:
ixm7ZgaG'); waitfor delay '0:0:15' --

Additional Information:
L3WX2lOf')); waitfor delay '0:0:15' --

Additional Information:
-5 OR 669=(SELECT 669 FROM PG_SLEEP(15))--

Additional Information:
-5) OR 526=(SELECT 526 FROM PG_SLEEP(15))--

Additional Information:
-1)) OR 99=(SELECT 99 FROM PG_SLEEP(15))--

Additional Information:
B3hszLzc' OR 556=(SELECT 556 FROM PG_SLEEP(15))--

Additional Information:
K9OJrDz1') OR 613=(SELECT 613 FROM PG_SLEEP(15))--

Additional Information:
73wbJn3w')) OR 247=(SELECT 247 FROM PG_SLEEP(15))--

Additional Information:

*DBMS_PIPE.RECEIVE_MESSAGE(CHR(99)||CHR(99)||CHR(99),15)

Additional Information:

'||DBMS_PIPE.RECEIVE_MESSAGE(CHR(98)||CHR(98)||CHR(98),15)||'

Additional Information:

'||DBMS_PIPE.RECEIVE_MESSAGE(CHR(98)||CHR(98)||CHR(98),15)||'

Additional Information:
1'"

Additional Information:
1����%2527%2522

Additional Information:
@@zROBD

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
HOW MUCH MDF IS USED FOR THE BOOK MACHINE COMBO #1