[ Log In ]
[ Register ]
NEW: CNC Router PLANS Available for all of our Newest CNC Models!! Click here to "Design Your CNC".

Question #: 532

Question: HOW MUCH MDF IS USED FOR THE BOOK MACHINE COMBO #1

Current Solution

Three 24" x 48" sheets of mdf is used for the book build or the combo #1 plans and kit.

Respond:

Other Possible Solutions to this Question

  • IS THE CNC MACHINE HARDWARE & PLANS COMBO SHOWN AT LINK YOU LISTED SAME DESCRIBED IN BOOK?

    Yes, the CNC machine hardware and plans combo is the same machine as in the book. The machine that we provide the plans for, can be found on the website, here http://buildyourcnc.com/Item/cnc-machine-scratchbuild

    Click the link to respond:
    IS THE CNC MACHINE HARDWARE & PLANS COMBO SHOWN AT LINK YOU LISTED SAME DESCRIBED IN BOOK?

  • How much Z-axis travel does the 48x96 greenlean machine have?

    The greenLean Z-axis travel is about 4" - 5"-3/4".

    Click the link to respond:
    How much Z-axis travel does the 48x96 greenlean machine have?

  • PARTS LIST FOR THE BOOK MACHINE

    The parts list is located on this page: http://buildyourcnc.com/cnckitintro.aspx at the bottom of the description.

    Click the link to respond:
    PARTS LIST FOR THE BOOK MACHINE

  • I bought an used machine that need work how can I find the model. The owner said, he used this site for parts and manual.

    If you purchased a machine that was used and you don't know which mode it is, you can browse our models here:
    https://www.buildyourcnc.com/Item/milling

    Click the link to respond:
    I bought an used machine that need work how can I find the model. The owner said, he used this site for parts and manual.

  • I received the electronics for book build cnc machine. I need to know how much weight the z-axis motor can hold since my (craftsman) router seems to be heavy. It is 2HP with variable speed

    The motor is helped by the mechanical leverage of the screw. The 425 oz-in motors that are included in the standard electronics combo has very high torque for that type of machine. You will have no problem using that motor for the book machine.

    We use that motor for very heavy spindles on the blackToe and blackFoot CNC Machine kits.

    You will need to do the mechanical leverage calculation along with the torque of the motor to determine the actual weight it will lift. The calculation will need to consider the type and pitch of the screw and it would also consider the gravity constant of 9.8 m/s/s.

    If you need me to determine this formula and work out the calculation based on the screw you are using, please let me know.

    Additional Information:
    thank you for the reply. I would be really good to know the calculation. The lead screw is 1/2" diameter with 13 TPI. Please provide the calculation. And one more question. If I am cutting 18mm MDF with 6mm cutting bit (so 6mm pass), what can be the maximum speed rate of cutting and spindle speed of router?
    thank you

    Click the link to respond:
    I received the electronics for book build cnc machine. I need to know how much weight the z-axis motor can hold since my (craftsman) router seems to be heavy. It is 2HP with variable speed

  • How long is the typical build time for one of our machines.

    The greenBull machine has a sturdier gantry than the blackFoot, so you can be more aggressive with the cutting feedrate (cutting speed). The blackFoot is also a good machine, but it all comes down to the speed at which you want to produce your arcade cabinets.

    I would highly recommend getting the spindle for cutting strength and easier cleanup, if you have 240v available.

    Click the link to respond:
    How long is the typical build time for one of our machines.

  • How long is the typical build time for one of our machines.

    The greenBull machine has a sturdier gantry than the blackFoot, so you can be more agressive with the cutting feedrate (cutting speed). The blackFoot is also a good machine, but it all comes down to the speed at which you want to produce your arcade cabinets.

    I would highly recommend getting the spindle for cutting strength and easier cleanup, if you have 240v available.

    Click the link to respond:
    How long is the typical build time for one of our machines.

  • Which electronics package is required for the CNC machine from the book designs?

    The book design uses all NEMA 23/24 motors which can be found here:
    https://buildyourcnc.com/item/electronicsAndMotors-3axis-425-elcombo

    I recommend the Mach3 USB option as you will be able to use the USB connection for control.

    If you are planning to build from the plans developed by the folks over at Woodsmith Magazine which is loosely based on the book design, use this electronics package:
    https://buildyourcnc.com/item/electronicsAndMotors-3axis-heavy-gantry-elcombo

    Click the link to respond:
    Which electronics package is required for the CNC machine from the book designs?

  • I read the book and i want the vedios show assembly the CNC Machines please give me alink for vedios

    The instructions for assembly are found in the book. If you are interested in purchasing the plans and instructional DVD please see this link https://buildyourcnc.com/cnckitintro.aspx

    Click the link to respond:
    I read the book and i want the vedios show assembly the CNC Machines please give me alink for vedios

  • IS THE HARDWARE AND PLANS MACHINE SAME AS BOOK MACHINE?

    Yes, the CNC machine hardware and plans combo is the same machine as in the book. The machine that we provide the plans for, can be found on the website, here http://buildyourcnc.com/Item/cnc-machine-scratchbuild

    Click the link to respond:
    IS THE HARDWARE AND PLANS MACHINE SAME AS BOOK MACHINE?

  • Can a CO2 CNC laser machine be used for welding of thermoplastic materials?

    That is a good question. We have not tried to weld thermoplastics using our CO2 Lasers. It is possible since the laser outputs a heat source and at the right intensity and speed, the thermoplastic can be heated and melted rather than instantaneously vaporized and off gassed. I have done research to see if CO2 laser can weld thermoplastics with positive results.

    Our CO2 lasers are typical of other laser cutters on the market, so if their literature, or examples you have found, successfully weld thermoplastics, then ours will probably be able to as well.

    In some cutting test with different speeds and intensities, the kerf has welded back together; however, this was caused by an unintentional process rather than an intentional one.

    Click the link to respond:
    Can a CO2 CNC laser machine be used for welding of thermoplastic materials?

  • IS DRILL BIT USED IN THE CNC MACHINE?

    The cutting tool is an end mill (it looks like a drill bit). It is a cutting tool that can plunge and cut sideways. That item is not included and is a consumable. You will purchase these very frequently and will have geometry that is very specific to how you apply the cnc machine.

    Click the link to respond:
    IS DRILL BIT USED IN THE CNC MACHINE?

  • What is the z-axis travel for your largest machine?

    The largest CNC machine we make at this time (12/04/2015) is the GreenBull 6'x12' model. This model has 2 options for Z-axis travel.

    The short-z option has a total Z travel of 5.75 inches. From that you would subtract the length of the end mill used and the thickness of the spoil board to determine the maximum material thickness. (Example: If the end mill extends 1.25" from the collet and the spoil board is .75", then the material could be up to 5.75 - 1.25 - 0.75 = 3.75 inches in thickness). This is good for most sheet-type materials.

    The long-z option, used mainly for large 3D carvings, requires a custom frame and allows for up to 36" of travel.

    Click the link to respond:
    What is the z-axis travel for your largest machine?

  • Is it possible to buy the plans for the 4'x8' machine?

    The files and hardware option for our machines has been removed from the site due to the following reasons:
    Difficulty for the end use of the files and the challenges (and time/money) on our side to assist in using these files.
    The abuse of these files over the internet.
    Ultimately may reduce the sales of machines keeping us in business.
    Sadly, this is what has come out of our company attempting to be open; however, the machines sold on this site is still far lower in price than the competition for the quality that we provide as we have a great desire to engender the cottage industry to fulfill their need for low end manufacturing. My sincere apologies if this causes any inconvenience.

    Additional Information:
    NO, is not possible, I can help with the shipping cost

    Click the link to respond:
    Is it possible to buy the plans for the 4'x8' machine?

  • I WOULD BE USING THIS MACHINE IN FIJI. MDF DELAMINATES OVER TIME HERE. HOW PROTECT THE FROM DELAMINATION?

    I WOULD CONSIDER USING A BOARD MADE OUT OF CLOTH AND RESIN AND IS USED IN ELECTRICAL AREAS AS AN INSULATOR. IT IS USUALLY A DARK RED/BROWN IN COLOR AND COMES IN DIFFERENT SIZES. IT IS VERY STRONG AND HEAVY. I DO NOT RECALL THE NAME OF IT, BUT POWER COMPANY LINEMEN HAVE ACCESS TO IT AS IT IS USED IN HIGH VOLTAGE AREAS.

    Response:
    I FOUND A LINK FOR YOU TO SEE WHAT I AM DESCRIBING. HERE IS THE LINK.. www.electricalinsulationmaterial.com

    Response:
    Currently our machines are made out of MDO (Medium Density Overlay) plywood, and are used in the construction industry for cement forming. They come lightly coated for moisture protection. Some possibilities for protecting the machine could be:
    Painting the structural parts with a oil based paint
    Coating the structural parts with a protectant sealant (polyurethane)

    Please try to avoid getting any coating or paints on the steel components.

    Click the link to respond:
    I WOULD BE USING THIS MACHINE IN FIJI. MDF DELAMINATES OVER TIME HERE. HOW PROTECT THE FROM DELAMINATION?

  • WHAT IS THE LEAD TIME FOR REDFROG PICK AND PLACE MACHINE?

    You can expect a two week lead time for the redFrog pick and place machine.

    Click the link to respond:
    WHAT IS THE LEAD TIME FOR REDFROG PICK AND PLACE MACHINE?

  • Just purchased the book "Build Your Own CNC Machine". Can I get hardware and electronics kits and how?

    The electronics (stepper motors, drivers, power supply and interface board) can be found here:
    https://www.buildyourcnc.com/item/electronicsAndMotors-3axis-425-elcombo

    If your computer cannot connect to the parallel breakout board (the interface card), just make sure to inform us that you need the USB alternative.

    Click the link to respond:
    Just purchased the book "Build Your Own CNC Machine". Can I get hardware and electronics kits and how?

  • Is there any way i can order replacement wooden parts for a cnc machine

    Yes, you can order replacement wooden parts, but since we don't have them as products on the website, you will need to call us directly using the number at the top right corner of the website by hovering over "need help?"

    Click the link to respond:
    Is there any way i can order replacement wooden parts for a cnc machine

  • I would be using this machine in Fiji. MDF delaminates over time here. How would I protect the machine from delamination?

    I WOULD CONSIDER USING A BOARD MADE OUT OF CLOTH AND RESIN AND IS USED IN ELECTRICAL AREAS AS AN INSULATOR. IT IS USUALLY A DARK RED/BROWN IN COLOR AND COMES IN DIFFERENT SIZES. IT IS VERY STRONG AND HEAVY. I DO NOT RECALL THE NAME OF IT, BUT POWER COMPANY LINEMEN HAVE ACCESS TO IT AS IT IS USED IN HIGH VOLTAGE AREAS.

    Response:
    I FOUND A LINK FOR YOU TO SEE WHAT I AM DESCRIBING. HERE IS THE LINK.. www.electricalinsulationmaterial.com

    Response:
    Currently our machines are made out of MDO (Medium Density Overlay) plywood, and are used in the construction industry for cement forming. They come lightly coated for moisture protection. Some possibilities for protecting the machine could be:
    Painting the structural parts with a oil based paint
    Coating the structural parts with a protectant sealant (polyurethane)

    Please try to avoid getting any coating or paints on the steel components.

    Click the link to respond:
    I would be using this machine in Fiji. MDF delaminates over time here. How would I protect the machine from delamination?

Get Help with:
This Product
Orders
Tech Support
Sales
This Product
Order Query
Tech Support
Sales
Not logged in. Log In Register
Track Order(s)
View Order(s)
I Want to Schecule a One-On-One Paid Tech Support Session
Book an Appointment Pertaining to a BuildYourCNC Product (Free)
Ask a Quesion Below (Free):
Book an Appointment Pertaining Other Equipment ($60/half hour)
Book an Immedite Appointment Pertaining Other Equipment ($120/half hour)
Ask a Quesion Below (Free):
Waiting for response... I may not answer immediately, but I was notified on my cellular phone so my response is forthcoming. If I don't respond immediately, you can always go to the [My Account] page to see all of our chats at any time.