[ Register ]

### Question #: 14244

Question: How many revelolutions nema 23 425 oz

Current Solution

The number of revolutions for a stepper motor is infinite as long as the stepper motor coils are being engaged by the driver and that the driver is being sent pulses and that the driver has sufficient power to engage the coils.

With that said, all of our stepper motors have 200 steps per revolution, which may be the answer you may be seeking. The steps per revolution can be increased by microsteps using the driver. In some drivers, this can be as much as 256 microsteps which brings the steps per revolution to 51,200 steps.

Respond:

### Other Possible Solutions to this Question

• How do I wire to nema 23 motors parallel

Wiring two motors in parallel is pretty easy.

Here are the steps:
- You need to have two stepper motors and two stepper motor drivers.
- Each stepper motor will be connected to its own stepper motor driver.
- Both stepper motor drivers are connected to the same CP and CW pins on the interface so the same signal is delivered to both drivers.

How do I wire to nema 23 motors parallel

• HOW MANY SIDES DOES A TRIANGLE HAVE?

The triangle has three (3) sides. The triangle is a polygon that contains three sides and three inner angles and three vertices.

But if a triangle have a front and back side wouldn't the triangle have 5 sides

Interesting slant (pun). A triangle would have 5 sides if the triangle had a thickness and became an object. A triangle drawn on paper with three lines would still only have three sides. A triangle is a primitive form of geometry (polygon) that can only have three sides in its simplest form. If you add complexity to the triangle with a thickness and count two more sides, then it really isn't the simplest form of the triangle anymore and it becomes another geometrical 3D primitive like a triangular prism.

A triangle has multiply answers for number of sides but is made up of 3 lines.. this is because when connecting the 3rd line to form the shape you create an "inside". so you could say a triangle has 2 sides, an "outside" and "inside" or you could say 4 sides, an "inside" and 3 "outside facings" or 6 sides 3 "outside facings" and 3 "inside facings". none of these answers are incorrect technically. the important thing is that a triangle is made up of 3 inner angles adding upto 180 degree's.

A triangle has 6 sides, there are 3 straight edges in AND out side of a triangle.

I am fairly sure that a triangle has 12 sides (3 insides and 3 outsides on each side).

4

4

4

How many sides do a triangle have

How many sides do a triangle have

How many sides do a triangle have

4

HOW MANY SIDES DOES A TRIANGLE HAVE?

• HOW MANY STRINGS DOES A VIOLIN HAVE?

The violin has four strings.

3

HOW MANY STRINGS DOES A VIOLIN HAVE?

• HOW MANY AXES CAN MACH 3 CONTROL?

Mach 3 CNC software can do the following:

Converts a standard PC to a fully featured, 6-axis CNC controller
Allows direct import of DXF, BMP, JPG, and HPGL files through LazyCam
Visual Gcode display
Generates Gcode via LazyCam or Wizards
Fully customizable interface
Customizable M-Codes and Macros using VBscript

SET:

Spindle Speed control
Multiple relay control
Manual pulse generation
Video display of machine
Touch screen ability
Full screen eligibility

EQUIPMENT:

Lathes
Mills
Routers
Lasers
Plasma
Engravers
Gear cutting

how to wire relay with mach board. I have mach interface board with one relay

HOW MANY AXES CAN MACH 3 CONTROL?

• HOW MANY STEPS PER INCH DO I SET IN MOTOR TUNING?

blueChick:

X-axis
“CW230 (3.0A) Driver”
Set to 1/16 Microstep, 2.7A
Dipswitches: 11001100
Mach3 Motor Tuning: 1422.22 steps/in

Y-axis
“CW230 (3.0A) Driver”
Set to 1/16 Microstep, 2.7A
Dipswitches: 11001100
Mach3 Motor Tuning: 1422.22 steps/in

Z-axis
“CW230 (3.0A) Driver”
Set to 1/4 Microstep, 2.7A
Dipswitches: 10101100
Mach3 Motor Tuning: 1600 steps/in

blackToe:

X-axis
“CW230 (3.0A) Driver”
Set to 1/16 Microstep, 2.7A
Dipswitches: 11001100
Mach3 Motor Tuning: 1422.22 steps/in

Y-axis
“CW230 (3.0A) Driver”
Set to 1/16 Microstep, 2.7A
Dipswitches: 11001100
Mach3 Motor Tuning: 1422.22 steps/in

Z-axis
“CW230 (3.0A) Driver”
Set to 1/4 Microstep, 2.7A
Dipswitches: 10101100
Mach3 Motor Tuning: 1600 steps/in

blackFoot:

X-axis
“CW8060 (6.0A) Driver”
Set to 1/16 Microstep, 2.7A
Dipswitches: 11001100 (“0”=down, “1”=up)
Mach3 Motor Tuning: 914.29 steps/in

Y-axis
“CW230 (3.0A) Driver”
Set to 1/16 Microstep, 2.7A
Dipswitches: 11001100
Mach3 Motor Tuning: 1422.22 steps/in

Z-axis
“CW230 (3.0A) Driver”
Set to 1/4 Microstep, 2.7A
Dipswitches: 10101100
Mach3 Motor Tuning: 1600 steps/in

greenBull:

X-axis
“CW8060 (6.0A) Driver”
Set to 5.43A, 1/16 Microstep
Dipswitches: 01100110 (“0”=down, “1”=up)
Mach3 Motor Tuning: 914.29 steps/in

Y-axis
“CW8060 (6.0A) Driver”
Set to 5.43A, 1/16 Microstep
Dipswitches: 01100110
Mach3 Motor Tuning: 914.29 steps/in

Z-axis
“CW8060 (6.0A) Driver”
Set to 5.43A, 1/4 Microstep
Dipswitches: 01100100
Mach3 Motor Tuning: 1600 steps/in

Scratch-Build / Book-Build Kit:

X-axis
“CW230 (3.0A) Driver”
Set to 1/4 Microstep, 2.7A
Dipswitches: 10101100 (“0”=down, “1”=up)
Mach3 Motor Tuning: 1600 steps/in

Y-axis
“CW230 (3.0A) Driver”
Set to 1/4 Microstep, 2.7A
Dipswitches: 10101100
Mach3 Motor Tuning: 1600 steps/in

Z-axis
“CW230 (3.0A) Driver”
Set to 1/4 Microstep, 2.7A
Dipswitches: 10101100
Mach3 Motor Tuning: 1600 steps/in

Scratch built/book CNC with NEMA 34 motors and CW8060 microstep driver

L8NiICEm

-1 OR 2+427-427-1=0+0+0+1 --

-1 OR 2+145-145-1=0+0+0+1

-1' OR 2+101-101-1=0+0+0+1 --

-1' OR 2+739-739-1=0+0+0+1 or 'kXOzulhF'='

-1" OR 2+194-194-1=0+0+0+1 --

if(now()=sysdate(),sleep(15),0)

0'XOR(if(now()=sysdate(),sleep(15),0))XOR'Z

0"XOR(if(now()=sysdate(),sleep(15),0))XOR"Z

(select(0)from(select(sleep(15)))v)/*'+(select(0)from(select(sleep(15)))v)+'"+(select(0)from(select(sleep(15)))v)+"*/

-1; waitfor delay '0:0:15' --

TO93cbNY

-1 OR 2+824-824-1=0+0+0+1 --

-1 OR 2+681-681-1=0+0+0+1

-1' OR 2+805-805-1=0+0+0+1 --

-1' OR 2+93-93-1=0+0+0+1 or 'MpFdFb3O'='

-1" OR 2+275-275-1=0+0+0+1 --

-1); waitfor delay '0:0:15' --

if(now()=sysdate(),sleep(15),0)

-1); waitfor delay '0:0:7' --

0'XOR(if(now()=sysdate(),sleep(15),0))XOR'Z

-1); waitfor delay '0:0:15' --

0'XOR(if(now()=sysdate(),sleep(15),0))XOR'Z

-1)); waitfor delay '0:0:15' --

0"XOR(if(now()=sysdate(),sleep(15),0))XOR"Z

1 waitfor delay '0:0:15' --

0"XOR(if(now()=sysdate(),sleep(9),0))XOR"Z

2k2XS4cL'; waitfor delay '0:0:15' --

(select(0)from(select(sleep(15)))v)/*'+(select(0)from(select(sleep(15)))v)+'"+(select(0)from(select(sleep(15)))v)+"*/

g7NWXuig'); waitfor delay '0:0:15' --

-1; waitfor delay '0:0:15' --

XoN629J2')); waitfor delay '0:0:15' --

-1); waitfor delay '0:0:15' --

-5 OR 247=(SELECT 247 FROM PG_SLEEP(15))--

-1)); waitfor delay '0:0:15' --

-5) OR 122=(SELECT 122 FROM PG_SLEEP(15))--

1 waitfor delay '0:0:15' --

-1)) OR 455=(SELECT 455 FROM PG_SLEEP(15))--

o1WPxXu4'; waitfor delay '0:0:15' --

X3pq07N4' OR 218=(SELECT 218 FROM PG_SLEEP(15))--

i2jhQp7d'); waitfor delay '0:0:15' --

xMv7x4te') OR 71=(SELECT 71 FROM PG_SLEEP(15))--

IbKvmZZx')); waitfor delay '0:0:15' --

YkhmkP9W')) OR 826=(SELECT 826 FROM PG_SLEEP(15))--

-5 OR 539=(SELECT 539 FROM PG_SLEEP(15))--

-5) OR 160=(SELECT 160 FROM PG_SLEEP(15))--

1'"

1����%2527%2522

@@EQr47

-1)) OR 220=(SELECT 220 FROM PG_SLEEP(15))--

-1)) OR 266=(SELECT 266 FROM PG_SLEEP(9))--

-1)) OR 107=(SELECT 107 FROM PG_SLEEP(0))--

vL4vUHTG' OR 262=(SELECT 262 FROM PG_SLEEP(15))--

gGLXRSqE' OR 938=(SELECT 938 FROM PG_SLEEP(15))--

WT10Ii3x' OR 598=(SELECT 598 FROM PG_SLEEP(9))--

QUuBKFso') OR 152=(SELECT 152 FROM PG_SLEEP(15))--

nI56G5Pp')) OR 493=(SELECT 493 FROM PG_SLEEP(15))--

1'"

1����%2527%2522

@@nxzWO

vJlQYk5k

-1 OR 2+406-406-1=0+0+0+1 --

-1 OR 2+236-236-1=0+0+0+1

-1' OR 2+914-914-1=0+0+0+1 --

-1' OR 2+282-282-1=0+0+0+1 or '9J7jHjSj'='

-1" OR 2+210-210-1=0+0+0+1 --

if(now()=sysdate(),sleep(15),0)

0'XOR(if(now()=sysdate(),sleep(15),0))XOR'Z

0"XOR(if(now()=sysdate(),sleep(15),0))XOR"Z

0"XOR(if(now()=sysdate(),sleep(14),0))XOR"Z

0"XOR(if(now()=sysdate(),sleep(15),0))XOR"Z

0"XOR(if(now()=sysdate(),sleep(0),0))XOR"Z

(select(0)from(select(sleep(15)))v)/*'+(select(0)from(select(sleep(15)))v)+'"+(select(0)from(select(sleep(15)))v)+"*/

-1; waitfor delay '0:0:15' --

-1); waitfor delay '0:0:15' --

-1)); waitfor delay '0:0:15' --

1 waitfor delay '0:0:15' --

RO4xZyuD'; waitfor delay '0:0:15' --

n2HpQRHN'); waitfor delay '0:0:15' --

hd4dcDEY')); waitfor delay '0:0:15' --

-5 OR 237=(SELECT 237 FROM PG_SLEEP(15))--

-5) OR 65=(SELECT 65 FROM PG_SLEEP(15))--

-1)) OR 486=(SELECT 486 FROM PG_SLEEP(15))--

-1)) OR 399=(SELECT 399 FROM PG_SLEEP(14))--

x4ZvP74B' OR 337=(SELECT 337 FROM PG_SLEEP(15))--

0VRZpjOv') OR 601=(SELECT 601 FROM PG_SLEEP(15))--

DrCdekI1')) OR 16=(SELECT 16 FROM PG_SLEEP(15))--

MQqu0z64')) OR 87=(SELECT 87 FROM PG_SLEEP(7))--

1'"

1����%2527%2522

@@HJ5oY

HOW MANY STEPS PER INCH DO I SET IN MOTOR TUNING?

• HOW MANY STEPS PER INCH?

blueChick:

X-axis
“CW230 (3.0A) Driver”
Set to 1/16 Microstep, 2.7A
Dipswitches: 11001100
Mach3 Motor Tuning: 1422.22 steps/in

Y-axis
“CW230 (3.0A) Driver”
Set to 1/16 Microstep, 2.7A
Dipswitches: 11001100
Mach3 Motor Tuning: 1422.22 steps/in

Z-axis
“CW230 (3.0A) Driver”
Set to 1/4 Microstep, 2.7A
Dipswitches: 10101100
Mach3 Motor Tuning: 1600 steps/in

blackToe:

X-axis
“CW230 (3.0A) Driver”
Set to 1/16 Microstep, 2.7A
Dipswitches: 11001100
Mach3 Motor Tuning: 1422.22 steps/in

Y-axis
“CW230 (3.0A) Driver”
Set to 1/16 Microstep, 2.7A
Dipswitches: 11001100
Mach3 Motor Tuning: 1422.22 steps/in

Z-axis
“CW230 (3.0A) Driver”
Set to 1/4 Microstep, 2.7A
Dipswitches: 10101100
Mach3 Motor Tuning: 1600 steps/in

blackFoot:

X-axis
“CW8060 (6.0A) Driver”
Set to 1/16 Microstep, 2.7A
Dipswitches: 11001100 (“0”=down, “1”=up)
Mach3 Motor Tuning: 914.29 steps/in

Y-axis
“CW230 (3.0A) Driver”
Set to 1/16 Microstep, 2.7A
Dipswitches: 11001100
Mach3 Motor Tuning: 1422.22 steps/in

Z-axis
“CW230 (3.0A) Driver”
Set to 1/4 Microstep, 2.7A
Dipswitches: 10101100
Mach3 Motor Tuning: 1600 steps/in

greenBull:

X-axis
“CW8060 (6.0A) Driver”
Set to 5.43A, 1/16 Microstep
Dipswitches: 01100110 (“0”=down, “1”=up)
Mach3 Motor Tuning: 914.29 steps/in

Y-axis
“CW8060 (6.0A) Driver”
Set to 5.43A, 1/16 Microstep
Dipswitches: 01100110
Mach3 Motor Tuning: 914.29 steps/in

Z-axis
“CW8060 (6.0A) Driver”
Set to 5.43A, 1/4 Microstep
Dipswitches: 01100100
Mach3 Motor Tuning: 1600 steps/in

Scratch-Build / Book-Build Kit:

X-axis
“CW230 (3.0A) Driver”
Set to 1/4 Microstep, 2.7A
Dipswitches: 10101100 (“0”=down, “1”=up)
Mach3 Motor Tuning: 1600 steps/in

Y-axis
“CW230 (3.0A) Driver”
Set to 1/4 Microstep, 2.7A
Dipswitches: 10101100
Mach3 Motor Tuning: 1600 steps/in

Z-axis
“CW230 (3.0A) Driver”
Set to 1/4 Microstep, 2.7A
Dipswitches: 10101100
Mach3 Motor Tuning: 1600 steps/in

Scratch built/book CNC with NEMA 34 motors and CW8060 microstep driver

L8NiICEm

-1 OR 2+427-427-1=0+0+0+1 --

-1 OR 2+145-145-1=0+0+0+1

-1' OR 2+101-101-1=0+0+0+1 --

-1' OR 2+739-739-1=0+0+0+1 or 'kXOzulhF'='

-1" OR 2+194-194-1=0+0+0+1 --

if(now()=sysdate(),sleep(15),0)

0'XOR(if(now()=sysdate(),sleep(15),0))XOR'Z

0"XOR(if(now()=sysdate(),sleep(15),0))XOR"Z

(select(0)from(select(sleep(15)))v)/*'+(select(0)from(select(sleep(15)))v)+'"+(select(0)from(select(sleep(15)))v)+"*/

-1; waitfor delay '0:0:15' --

TO93cbNY

-1 OR 2+824-824-1=0+0+0+1 --

-1 OR 2+681-681-1=0+0+0+1

-1' OR 2+805-805-1=0+0+0+1 --

-1' OR 2+93-93-1=0+0+0+1 or 'MpFdFb3O'='

-1" OR 2+275-275-1=0+0+0+1 --

-1); waitfor delay '0:0:15' --

if(now()=sysdate(),sleep(15),0)

-1); waitfor delay '0:0:7' --

0'XOR(if(now()=sysdate(),sleep(15),0))XOR'Z

-1); waitfor delay '0:0:15' --

0'XOR(if(now()=sysdate(),sleep(15),0))XOR'Z

-1)); waitfor delay '0:0:15' --

0"XOR(if(now()=sysdate(),sleep(15),0))XOR"Z

1 waitfor delay '0:0:15' --

0"XOR(if(now()=sysdate(),sleep(9),0))XOR"Z

2k2XS4cL'; waitfor delay '0:0:15' --

(select(0)from(select(sleep(15)))v)/*'+(select(0)from(select(sleep(15)))v)+'"+(select(0)from(select(sleep(15)))v)+"*/

g7NWXuig'); waitfor delay '0:0:15' --

-1; waitfor delay '0:0:15' --

XoN629J2')); waitfor delay '0:0:15' --

-1); waitfor delay '0:0:15' --

-5 OR 247=(SELECT 247 FROM PG_SLEEP(15))--

-1)); waitfor delay '0:0:15' --

-5) OR 122=(SELECT 122 FROM PG_SLEEP(15))--

1 waitfor delay '0:0:15' --

-1)) OR 455=(SELECT 455 FROM PG_SLEEP(15))--

o1WPxXu4'; waitfor delay '0:0:15' --

X3pq07N4' OR 218=(SELECT 218 FROM PG_SLEEP(15))--

i2jhQp7d'); waitfor delay '0:0:15' --

xMv7x4te') OR 71=(SELECT 71 FROM PG_SLEEP(15))--

IbKvmZZx')); waitfor delay '0:0:15' --

YkhmkP9W')) OR 826=(SELECT 826 FROM PG_SLEEP(15))--

-5 OR 539=(SELECT 539 FROM PG_SLEEP(15))--

-5) OR 160=(SELECT 160 FROM PG_SLEEP(15))--

1'"

1����%2527%2522

@@EQr47

-1)) OR 220=(SELECT 220 FROM PG_SLEEP(15))--

-1)) OR 266=(SELECT 266 FROM PG_SLEEP(9))--

-1)) OR 107=(SELECT 107 FROM PG_SLEEP(0))--

vL4vUHTG' OR 262=(SELECT 262 FROM PG_SLEEP(15))--

gGLXRSqE' OR 938=(SELECT 938 FROM PG_SLEEP(15))--

WT10Ii3x' OR 598=(SELECT 598 FROM PG_SLEEP(9))--

QUuBKFso') OR 152=(SELECT 152 FROM PG_SLEEP(15))--

nI56G5Pp')) OR 493=(SELECT 493 FROM PG_SLEEP(15))--

1'"

1����%2527%2522

@@nxzWO

vJlQYk5k

-1 OR 2+406-406-1=0+0+0+1 --

-1 OR 2+236-236-1=0+0+0+1

-1' OR 2+914-914-1=0+0+0+1 --

-1' OR 2+282-282-1=0+0+0+1 or '9J7jHjSj'='

-1" OR 2+210-210-1=0+0+0+1 --

if(now()=sysdate(),sleep(15),0)

0'XOR(if(now()=sysdate(),sleep(15),0))XOR'Z

0"XOR(if(now()=sysdate(),sleep(15),0))XOR"Z

0"XOR(if(now()=sysdate(),sleep(14),0))XOR"Z

0"XOR(if(now()=sysdate(),sleep(15),0))XOR"Z

0"XOR(if(now()=sysdate(),sleep(0),0))XOR"Z

(select(0)from(select(sleep(15)))v)/*'+(select(0)from(select(sleep(15)))v)+'"+(select(0)from(select(sleep(15)))v)+"*/

-1; waitfor delay '0:0:15' --

-1); waitfor delay '0:0:15' --

-1)); waitfor delay '0:0:15' --

1 waitfor delay '0:0:15' --

RO4xZyuD'; waitfor delay '0:0:15' --

n2HpQRHN'); waitfor delay '0:0:15' --

hd4dcDEY')); waitfor delay '0:0:15' --

-5 OR 237=(SELECT 237 FROM PG_SLEEP(15))--

-5) OR 65=(SELECT 65 FROM PG_SLEEP(15))--

-1)) OR 486=(SELECT 486 FROM PG_SLEEP(15))--

-1)) OR 399=(SELECT 399 FROM PG_SLEEP(14))--

x4ZvP74B' OR 337=(SELECT 337 FROM PG_SLEEP(15))--

0VRZpjOv') OR 601=(SELECT 601 FROM PG_SLEEP(15))--

DrCdekI1')) OR 16=(SELECT 16 FROM PG_SLEEP(15))--

MQqu0z64')) OR 87=(SELECT 87 FROM PG_SLEEP(7))--

1'"

1����%2527%2522

@@HJ5oY

HOW MANY STEPS PER INCH?

• Is the shaft diameter of the NEMA 23 motor 1/4 inch?

The NEMA 23 425-oz in. motor has both input shafts at a 1/4".

Is the shaft diameter of the NEMA 23 motor 1/4 inch?

• I am using your 425 Oz motors

The ports and pins are designated by the breakout board that you have, Now here are the schematics for both(https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay#prettyPhoto/2/ and https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout#prettyPhoto/2/) Which for the Parallel the pins will be 1,14,2,3,4,5,6,7,8,9. For 1,14 you will need to use them together for a additional axis. Setup will be (ex.mach3) step in (2) / direction pin (3). continued for other pins, 4,5 6,7 etc.
Now for the USB it has the label on the board right next to the terminal blocks, x-axis/etc.

I am using your 425 Oz motors

• The motor was tested on the same axes were the others work but one of the NEMA 24 425 Oz motors dose not turn just jitters.

The NEMA 25 motor uses a different current than other motors. Make sure when you test the NEMA 25 motor, the current setting is at 2.43.

The motor was tested on the same axes were the others work but one of the NEMA 24 425 Oz motors dose not turn just jitters.

• What is the number of pole pairs and rotor inertia for NEMA 23 Stepping motor?

You can find the wiring diagram, and technical specifications for the NEMA 23 motor, on it's product page, found here,

https://www.buildyourcnc.com/Item/electronicsAndMotors-nema23-100ozin-newbiehack-motors-stepping_motors-100_ozin

There is a datasheet below the product description. This image will expand to be easier visible once clicked on.

What is the number of pole pairs and rotor inertia for NEMA 23 Stepping motor?

• what is the driver needed for 425OZ on nema 24

The driver that the 425 oz-in motor requires is a 3.0 amp stepper motor driver found here:
https://www.buildyourcnc.com/item/electronicsAndMotors-stepper-driver-3!0a

This driver has the capability of various stepper motor current draws up to 3.0 amps.

what is the driver needed for 425OZ on nema 24

• HOW DO YOU HOOK UP THE VFD TO SPINDLE?

U - Pin1
V - Pin2
W - Pin3

My home made cnc is a big problem with my NC connection. When in start my spindle it will be gone wrong. It will be limith switch problem anytime. Need help thanks.

HOW DO YOU HOOK UP THE VFD TO SPINDLE?

• HOW DO YOU CONNECT THE INVERTER TO AC?

Input to VFD:
240V Active - R
240V Neutral - S
Ground - E

HOW DO YOU CONNECT THE INVERTER TO AC?

• HOW DO YOU SETUP THE SPINDLE INVERTER?

Change PD001 Source of Run Commands to '1'
Change PD005 Max operating frequency to 400hz
Change PD004 base frequency to 400hz
Change PD003 Main frequency to 400hz
Change PD006 Intermediate frequency to 2.5
Change PD008 max voltage to 220v
Change PD009 Intermediate voltage to 15v
Change PD010 Min voltage to 8
Change PD011 frequency lower limit to >100hz (120hz to start)
Change PD142 7 Amps
Change PD143 2
Change PD144 3000

Note: PD001 had to be changed back to 0 to allow for keypad control.
Note2: I had to reverse U and V to get the spindle to go forward in FWD. (reverse any two wires, u&v or w&v for example)

HOW DO YOU SETUP THE SPINDLE INVERTER?

• HOW HARD CAN PUSH MY BLACKTOOTH LASER?

These tubes are rated for 18mA. The power supply is able to push up to 21mA. This is a very dangerous thing to do. If you are pushing the tube beyond 18mA you will cut it's life by QUITE a bit.

HOW HARD CAN PUSH MY BLACKTOOTH LASER?

• HOW CAN MOUNT THE EXTRUDER TO WHITEANT

Mounting the extruder to the whiteAnt can be done a couple of ways. One is to take the 4 mounting holes located at the lower portion of the z-axis rail support and use long screws protruding out. Take a thinner material and drill the four holes matching the locations of the 4 screws and screw on nuts to hold it in place. The other option would be to use the metal bracket and fasten to the edge of the rail support.

HOW CAN MOUNT THE EXTRUDER TO WHITEANT

• I have theNema 24, 425 Oz stepper motors kit what are my Ports and Pins?

The ports and pins are designated by the breakout board that you have, Now here are the schematics for both(https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay#prettyPhoto/2/ and https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout#prettyPhoto/2/) Which for the Parallel the pins will be 1,14,2,3,4,5,6,7,8,9. For 1,14 you will need to use them together for a additional axis. Setup will be (ex.mach3) step in (2) / direction pin (3). continued for other pins, 4,5 6,7 etc.
Now for the USB it has the label on the board right next to the terminal blocks, x-axis/etc.

I have theNema 24, 425 Oz stepper motors kit what are my Ports and Pins?

• HOW MUCH MOTOR CABLE FOR THE BLACKFOOT?

The motor cables for the blackToe are as follows:

Total 30 feet

X - 9
Y - 10
Z - 11

HOW MUCH MOTOR CABLE FOR THE BLACKFOOT?

• HOW SHOULD I CARE FOR MAY GRAPEVINES?

Vines are normally planted bare root from January to March and spaced 7 to 8 feet apart in rows 10 to 12 feet apart. Vertical stakes or posts with 1 or 2 wires on the side, or with “T” tops with wire are desirable supports for grapevines. Cane prune Thompson seedless and Concord. Spur prune other varieties. Frost (31oF) damages new shoots and fruit clusters in April or May, so plant where the frost is minimized. Spraying or dusting sulfur for mildew is necessary on wine and table grapes, but rarely needed with American types. (From http://ucce.ucdavis.edu/files/filelibrary/40/935.pdf )

HOW SHOULD I CARE FOR MAY GRAPEVINES?

Get Help with:
This Product
Orders
Tech Support
Sales
This Product
Order Query
Tech Support
Sales