[ Log In ]
[ Register ]
NEW: CNC Router PLANS Available for all of our Newest CNC Models!! Click here to "Design Your CNC".

Question #: 14230

Question: How do I wire to nema 23 motors parallel

Current Solution

Wiring two motors in parallel is pretty easy.

Here are the steps:
- You need to have two stepper motors and two stepper motor drivers.
- Each stepper motor will be connected to its own stepper motor driver.
- Both stepper motor drivers are connected to the same CP and CW pins on the interface so the same signal is delivered to both drivers.

Respond:

Other Possible Solutions to this Question

  • How do I wire two motors parallel

    To have two stepper motors move simultaneously, connect the two stepper motor drivers to the same CP (step pulse) and CW (direction) pins for that axis.

    Additional Information:
    Can you send me a wiring diagram
    kkitching@hughes.net

    Click the link to respond:
    How do I wire two motors parallel

  • I need wiring diagram to wire two nema motors parallel

    To move two stepper motors simultaneously with the same signal, simply wire the two stepper motor drivers to the same interface board signal terminals (CP and CW).

    Additional Information:
    using a ardino uno controller and a cnc sheild on top of that how to wirer 2 motors to 1 axis its the x axis ?

    Click the link to respond:
    I need wiring diagram to wire two nema motors parallel

  • How do I wire two stepper motors for one axis?

    Yes, you can use 2 motors in the same axis output, however you will still need a driver for that motor! Also depending on the orientation on which you mount the motor you might have to invert the direction of the motor, and that will be simple by swapping the A+,A-, to the B+,B- locations and vice versa, from the driver to the motor wiring.

    Also you can run a slave motor using another axis on the board, and setting it up in the Planet-CNC settings.

    Planet-CNC/File/Settings/Axes, here you will enter 3 in the Number of Axes location, and then change the Function of the Axis 4 to Slave 1. There you will have the 4th axis or A-axis be a slave for the x-axis.
    Slave 1 - X-Axis
    Slave 2 - Y-Axis
    Slave 3 - A-Axis
    Slave 4 - B-Axis
    Etc...

    Click the link to respond:
    How do I wire two stepper motors for one axis?

  • Can i wire my drivers and motors in parallel to your laser controll system to add a laser unit on my router?

    It is possible to add the laser control system to an existing CNC router but there are a few considerations:

    All of the signal wires from the laser controller that connect to the drivers drivers and all of the signal wires from the CNC controller that go to the drivers will need to first pass through a tri-state gate buffer chip that will allow one set of signal wires to be switched off and the other set switched on.

    We have a board that does this in development, but If you wish to accomplish this on your own, you will need:

    - 3 Quad buffer line drivers (each one can receive 4 signal wires): https://newbiehack.com/categories/newbiehack-integrated_circuits-buffer-quad-buffer-line-driver-throughhole
    - Some perf board, solder and a soldering iron, and some hookup wire.

    If this doesn't scare you, please feel free to submit additional information and let me know if you would like more information.


    Additional Information:
    You will also need a physical switch to select laser control or CNC control.

    Click the link to respond:
    Can i wire my drivers and motors in parallel to your laser controll system to add a laser unit on my router?

  • How long does it take to ship to Israel 3 nema 11 stepper motors ?

    Unfortunately I am not able to give an estimate of shipping time. This is because there are multiple shipping options, Some of them cost more than others, but ensure the package arrives in a certain number of days. Others do not give a number of days, and many factors could change the length of shipping time, such as weather, or busy season. It would be best to choose an option you are comfortable with the price of, and then Google search the typical times it takes for that option to get to you, or call the shipping company and request that estimated time from them.

    Click the link to respond:
    How long does it take to ship to Israel 3 nema 11 stepper motors ?

  • Regarding the heavy gantry electronics combo. When choosing the parallel breakout board option, how many axis/motors does the breakout board support? Thank you!
  • How do you connect the spindle VFD to the parallel breakout board

    The parallel board contains a relay that is connected to pin #16. You can use this relay as the start/stop by connecting the relay to the FOR and it's related digital GND pin on the VFD.

    Click the link to respond:
    How do you connect the spindle VFD to the parallel breakout board

  • I have my motors wired like the wiring diagram I have two motors on Y axis how do I wire the second motor

    To move two stepper motors simultaneously with the same signal, simply wire the two stepper motor drivers to the same interface board signal terminals (CP and CW).

    Additional Information:
    using a ardino uno controller and a cnc sheild on top of that how to wirer 2 motors to 1 axis its the x axis ?

    Click the link to respond:
    I have my motors wired like the wiring diagram I have two motors on Y axis how do I wire the second motor

  • How do I put two motors on the same axis

    Yes, you can use 2 motors in the same axis output, however you will still need a driver for that stepper motor. Also depending on the orientation on which you mount the motor you might have to invert the direction of the motor, and that will be simple by swapping the A+,A-, to the B+,B- locations and vice versa, from the driver to the motor wiring.

    The wiring scheme would look like this:
    The step and direction output terminals on the CNC controller interface for the axis you want to have two motors would connect to both drivers of the two stepper motors on that axis.

    Additional Information:
    I have been running two motors from the same driver for 10 years on my 3m x 1.6m router. Both motors driving the gantry are wired together. I see no reason to use two drivers. The motors are high torque Nema 34. I've had no issues.

    Click the link to respond:
    How do I put two motors on the same axis

  • how do I connect the parallel breakout board?

    You can go here to find the diagrams and instruction on connecting the parallel breakout board:

    https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

    Also, please make sure to watch all of the electronics tutorial videos here:
    https://www.buildyourcnc.com/CNCElectronicsandWiring.aspx

    Click the link to respond:
    how do I connect the parallel breakout board?

  • how do I determine the steps per inch for the motors?

    blueChick:

    X-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    blackToe:

    X-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    blackFoot:

    X-axis
    “CW8060 (6.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 914.29 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/16 Microstep, 2.7A
    Dipswitches: 11001100
    Mach3 Motor Tuning: 1422.22 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    greenBull:

    X-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/16 Microstep
    Dipswitches: 01100110 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 914.29 steps/in

    Y-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/16 Microstep
    Dipswitches: 01100110
    Mach3 Motor Tuning: 914.29 steps/in

    Z-axis
    “CW8060 (6.0A) Driver”
    Set to 5.43A, 1/4 Microstep
    Dipswitches: 01100100
    Mach3 Motor Tuning: 1600 steps/in


    Scratch-Build / Book-Build Kit:

    X-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100 (“0”=down, “1”=up)
    Mach3 Motor Tuning: 1600 steps/in

    Y-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    Z-axis
    “CW230 (3.0A) Driver”
    Set to 1/4 Microstep, 2.7A
    Dipswitches: 10101100
    Mach3 Motor Tuning: 1600 steps/in

    Additional Information:


    Additional Information:
    Scratch built/book CNC with NEMA 34 motors and CW8060 microstep driver

    Additional Information:

    Click the link to respond:
    how do I determine the steps per inch for the motors?

  • how to connect parallel port breakout board for medium kit

    The very best way to explain how to connect the parallel breakout board is to follow these tutorials on this site: https://buildyourcnc.com/CNCElectronicsandWiring.aspx#prettyPhoto

    Click the link to respond:
    how to connect parallel port breakout board for medium kit

  • If motors are wired for Bipolar series which leads do you swap for rotation?

    For our motors, drivers and power supplies, we recommend bipolar parallel (relating to motors with more than 4 wires). The current draw and voltage combination under bipolar parallel results in better performance.

    To reverse the motor spin direction for both bipolar series or bipolar parallel, switching the "A" wires with the "B" wires will do the trick.

    Click the link to respond:
    If motors are wired for Bipolar series which leads do you swap for rotation?

  • I have your breakout board with relay parallel port , how can I wire up a regular router to that board so I can control the router

    Here is how to connect your router to the parallel breakout board through the on-board relay. You will need a spare extension cord. You will need to remove a portion of the outer jacket of the extension cord to expose the white, black and green wires (white = neutral, black = live and green = ground), understanding that the neutral and live create the completed circuit.

    See this image of a similar connection. The terminal has the same connections.
    https://www.buildyourcnc.com/images/vacuum-pressure-controller-relay-terminals-700.JPG

    Image of the relay terminal:
    https://www.buildyourcnc.com/images/breakoutboardrelayNONC.PNG

    The live/black wire would be cut and one end of the cut would be secured into the P terminal and the other cut end would be secured into the S terminal. The live and ground wire would be uncut and travel from the plug to the router.


    Additional Information:
    You can also connect other high powered devices to the breakout board using any of the output terminals. You will need to supply extra relays like the one shown here:
    https://www.buildyourcnc.com/item/electronicsAndMotors-breakout-Relays-relay-board-250V-12A-5V

    Or you can find SSRs (Solid State Relays) that will accept 5v to drive the relay coil. Make sure the SSR will protect the 5V line from Back EMF as there is a coil in the relay. The one we sell contains a fly-back diode to protect the 5v terminal.

    Click the link to respond:
    I have your breakout board with relay parallel port , how can I wire up a regular router to that board so I can control the router

  • My x and y motors are on each end of my gantry do I wire each motor to the same XP

    I'm not sure what you mean by XP. Can you clarify? Thanks.

    All stepper motors must be wired to their own stepper motor driver. If two motors need to be driven by one signal (say there are two X motors) then the two drivers will be connected to same CP (pulse or step) and CW (direction) pins on the control interface. If the two motors need to turn in opposite directions, then swap the A and B coil connections.

    Additional Information:
    Whitch A+ or A - B + or B -

    Click the link to respond:
    My x and y motors are on each end of my gantry do I wire each motor to the same XP

  • IS THERE A WAY TO GET RID OF THE PARALLEL CABLE AND SOMEHOW USE USB ?

    If you select the Settings Page and select or tick Auto Limit Override - this will allow you to back off the switch.

    Click the link to respond:
    IS THERE A WAY TO GET RID OF THE PARALLEL CABLE AND SOMEHOW USE USB ?

  • DO I HAVE TO A PARALLEL PORT?

    If your computer does not have a parallel port, all you will need is a low cost PCI parallel adapter card (these can be found on amazon for $15-$20). If you plan on using a laptop (not recommended) you can try to find a PCMCIA parallel adapter, but many people have frequent issues with this setup. A more expensive solution would be to purchase a USB smooth stepper board. Unfortunately, we do not supply any of these adapters and cannot attest to their reliability.

    Additional Information:
    ur gay

    Click the link to respond:
    DO I HAVE TO A PARALLEL PORT?

  • IF MY COMPUTER DOESN'T HAVE A PARALLEL PORT, HOW DO I RUN THE MACHINE?

    If your computer does not have a parallel port, all you will need is a low cost PCI parallel adapter card (these can be found on amazon for $15-$20). If you plan on using a laptop (not recommended) you can try to find a PCMCIA parallel adapter, but many people have frequent issues with this setup. A more expensive solution would be to purchase a USB smooth stepper board. Unfortunately, we do not supply any of these adapters and cannot attest to their reliability.

    Additional Information:
    ur gay

    Click the link to respond:
    IF MY COMPUTER DOESN'T HAVE A PARALLEL PORT, HOW DO I RUN THE MACHINE?

  • I HAVE NEMA 34 MOTORS BUT NEED THE ELECTRICAL COMPONENTS DO YOU A KIT WITHOUT INCLUDED?

    If you are looking for the drivers to pair with NEMA 34 stepper motors, you can find the 6.0 amp drivers here:
    https://www.buildyourcnc.com/item/electronicsAndMotors-stepper-driver-6!0a

    The other electronics to send the signals to the 6.0 amp drivers (the control board that operates with the control software) is subject to personal preference, but here they are listed:

    Our breakout board (works with Mach3 and LinuxCNC and requires a parallel port on your computer):
    https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

    The PoKeys57CNC (works with Mach3 and Mach4):
    https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

    Generic USB breakout board (works with Mach3):
    https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

    Click the link to respond:
    I HAVE NEMA 34 MOTORS BUT NEED THE ELECTRICAL COMPONENTS DO YOU A KIT WITHOUT INCLUDED?