Use the datasheet associated to the motor that you purchased. Use the bipolar parallel configuration to optimum performance. The datasheets are located in their respective motor product pages. Just click on the motion electronics at the left and scroll down to the motor you have and click on the title, or datasheet link next to the motor. The datasheet will either be in the form of a pdf, or within the instructions on that product page.

Additional Information:
wiring diagram



Additional Information:


Additional Information:

Click the link to add information to this solution:
How do I connect my motor wires to the driver?

If the motor has 8 wires, you will need to wire the stepper motor in bipolar parallel. This motor (425 oz-in) is wired as follows:

Red and Blue wires to A+ on driver
Yellow and Black wires to A- on driver
White and Brown wires to B+ on driver
Orange and Green wires to B- on driver

Click the link to add information to this solution:
[54] There are 8 wires on this motor. How do you connect to the driver?

From the USB controller, the CP+ and CW+ are connected to the 5V terminal. The CP- is connected to the CP terminal of the driver and the CW- is connected to the CW terminal of the driver.

Additional Information:

Click the link to add information to this solution:
Please explain how to connect 2.5AMP stepper motor driver to USB board. All parts are from your store. Thanks

Pul+ is the Step+ and Pul- is the Step-. Pul is short for pulse. A pulse will create a step. Don't worry about the enable terminals.

On the x-axis, pin #2 can go to pul- and pin #3 can go to dir-. The 5v will go to pul+ and dir+. The configuration for each axis for step will be active low and toggle active low for the dir on each axis to make it go in the direction desired.

Next time, purchase the drivers from us and you will have fewer problems.

Additional Information:


Additional Information:


Additional Information:


Additional Information:


Additional Information:
Hi, I have an IHSS57-36-20 stepper motor with integrated driver (pulse mode) in my printer but it looks the paper moving distance is changing according to the paper tension. Has this version any encoder or I lose some steps?
Thanks, John

Additional Information:
pin #2 can go to pul- and pin #3 can go to dir-

Additional Information:
pin #2 can go to pul- and pin #3 can go to dir-

Additional Information:
pin #2 can go to pul- and pin #3 can go to dir-

Click the link to add information to this solution:
My driver has Pul+,Pul-,Dir+,Dir-,Ena+,Ena-. How do I connect the driver to my BoB.

CP+ to COM
CP- to STEP
CP+ to CW+ (small jumper wire)
CW- to DIR

Additional Information:
If the driver does not have CP or CW labels, the CP is Step and the CW is Direction or DIR. If you connect the 5v to CP+ (or Step+) and CW+ (or DIR+) and the pin to CP- (or Step-) and another pin to CW- (or DIR-), then in software, the configuration for the step on that axis must be active low. Otherwise, if you connect the GND to CP- (or Step-) and CW- (or DIR-) and the pin to CP+ (or Step+) and another pin to CW+ (or DIR+), then in software, the configuration for the step on that axis must be active high.

Additional Information:
If you have a driver that is labeled pul, dir and ena: Pul+ is the Step+ and Pul- is the Step-. Pul is short for pulse. A pulse will create a step. Don't worry about the enable terminals.

On the x-axis, pin #2 can go to pul- and pin #3 can go to dir-. The 5v will go to pul+ and dir+. The configuration for each axis for step will be active low and toggle active low for the dir on each axis to make it go in the direction desired.

Additional Information:


Additional Information:


Additional Information:


Additional Information:

Click the link to add information to this solution:
HOW DO I WIRE FROM THE BREAKOUT BOARD TO DRIVER?

All you need is a CNC controller like the following options:

https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

This controller is easy to connect using standard wire screw terminals and works with the mach3 control software.

https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

This controller is a little bit more difficult to connect, but is a more feature-rich controller and will work with both mach3 and mach4 CNC control software titles.

Specifically, a CNC controller connects to the computer via a USB cable and connects to the motor drivers. These controllers also connect to the limit switches, spindle/router control, air/fluid/mist control, etc.

Click the link to add information to this solution:
How can I connect my pc to my motor drivers and motors?

Connecting a heater bed to the whiteAnt is currently unavailable with our current version electronics, as we have tried to get around that issue here! We do not have the available slot for another thermocouple, so reading the temperature will not be possible for the heater bed. Also doubling the heater bed and extruder is not recommended, in which our current electronics will not be able to work with the additional heater bed.

Click the link to add information to this solution:
How do I connect a heated bed to the whiteant

The instructions on how to do this are found here, in these two videos, http://buildyourcnc.com/PrimeronHomingandLimitSwitches.aspx

Additional Information:

Click the link to add information to this solution:
HOW DO I CONNECT A TOUCH PLATE TO THE BREAKOUT BOARD?

"Semi automatic" measuring is possible.
1. Place movable tool sensor (touch plate) on material.
2. Click "Measure Offset Z". Tool will move down, touch sensor and move up.
3. "Measure Offset Z" button is still down.
4. Click "Offset - Current Z" - this will set offset Z
5. Click "Measure Offset Z" again to release it and restore normal mode."

The connections to the USB interface is as follows:
- The spindle is connected to the gnd terminal (which is also connected to the end mill). Alternatively, you can connect the gnd directly to the end mill is access is permitted.
- The touch plate (movable tool sensor) is connected to the Z-- terminal.

What will happen: When the end mill (gnd) is in contact with the touch plate (Z--), there will be a connection from gnd to the Z-- triggering this Z-- action and the software will recognize the connection (like a button press, or a limit switch triggering).

Additional Information:


Additional Information:

Click the link to add information to this solution:
How do I connect a Z-Axis touch plate to the Planet-CNC USB interface?

The greenlean requires 56 feet of 1/4 Inside Diameter and 3/8 Outside Diameter silicon tube for the spindle.

Additional Information:
20

Additional Information:
20

Click the link to add information to this solution:
HOW MUCH SILICONE TUBE DO I NEED FOR A GREEN LEAN TO CONNECT THE SPINDLE

It is not necessary to connect the spindle VFD (Variable Frequency Drive also called an Inverter) to the computer or CNC motion electronics. The VFD can be controlled independently using the control panel on the VFD. The control panel has the ability to control all aspects of the spindle including Speed, Torque, limits, etc. However, you can connect the VFD to the computer so the CNC control program can control the spindle during the CNC Machine operation. You will need to connect the VFD to the computer via a serial conection (in this case, it is the RS-485 protocol).

The following are instructions on how to connect the VFD to Mach3 via this RS-485 serial connection.

The first thing you will need is the dynamic link library to pair with mach3 called the Huanyang VFD Mach3 PlugIn. You can find this file at the mach3 support forum here: http://www.machsupport.com/forum/index.php/topic,14182.0.html

You will also need to download the Microsoft .net 3.5 framework and install it: https://www.microsoft.com/en-us/download/details.aspx?id=21

Follow the pdf that comes with the library file, but here is a synopsis of what you need to do (I also added a lot more information that may be useful during this process as the manual does not cover the main connections that need to be done):

You will need to program your VFD so that it knows how to communicate with mach3 and the computer (go into the programming mode of the VFD and change these parameters):
- PD001 - value 2 - Enables with communication aspect of the VFD
- PD002 - value 2 - Enables frequency control from the communcations port
- PD163 - value 1 - VFD address
- PD164 - value 1 - Baud rate of 9600 (speed of the communication)
- PD165 - value 3 - 8N1 RTU - 8 bits (that's the size of the word that gets communicated), N (No parity or no error checking) and 1 (1 stop bit)

Copy the dll file to the PlugIns folder of mach3.

Connect the RX and TX lines to your computer. There are a couple ways you can do this, but the recommended way would be to use an FTDI USB device which converts a USB to a serial com port. The device will have Rx and Tx connectors to connect to the VFD terminals with the same labels. This method is recommended since serial ports are not as common in computers these days.

Next, you will need to configure mach3 to use the plugin library. Start mach3 and click on Menu -> config ->Config Plugins. Enable the new plugin by clicking on the red cross on the left column next to the plug in. Restart mach3 after doing this.

No you need to configure mach3 to use the HuanyangVFD plugin. Go to the ports & pins configuration and select the spindle setup tab. Make sure that the Disable Spindle Relays checkbox is unchecked. We don't want mach3 to output a signal for a relay since the spindle will start up and turn off within the VFD and not from an external relay.

Next, go to the HuanyangVFD settings by clicking on Menu -> plugin control -> HuanyangVFD. Set the parameters to the same settings you put into the VFD programming. The com port will be shown as new hardward when you plug in the USB FTDI device. A little bubble will be displayed at the bottom right where it will notify you that a new device is being installed (be patient while windows assigns a com port). Alternatively, you can use the windows device manager to see which port was set for the new USB FTDI device). You may need to restart mach3 several times until you get the correct information displayed in the PD001 and PD002 fields. When the com port is correct and the other parameters, like baud and VFD address is the same as you entered in the programming, then the PD001 and PD002 will show the number 2, otherwise, a 99 will appear which means that communication was not successful.

You can now control the on/off and RPM of the spindle using the RS485 communication between mach3 and the VFD.

Additional Information:
The question was how to connect the spindle to the redfy. I did not receive a VFD.
I have the redFly system and a 2.2kW Spindle - 110V how do i connect the spindle?

Additional Information:
If you received a spindle without a VFD, please contact us asap. Our spindle will not work without a VFD.

Additional Information:
Hi, how is this setup in mach4?

Click the link to add information to this solution:
how do I connect my spindle to mach3 so mach3 can control it

Connect the XD to the Dir, XP to the Step, and the 5V on the Mach3 USB controller to the +5V.

Click the link to add information to this solution:
[575] I have motor control boards that have 4 pin input ( Step, Dir, EN, +5V) how do I connect this USB board?

You can connect the 5V from the Mach3 USB controller to the 5V terminal on the driver, the XP to the Step terminal on the driver and the XD to the Dir terminal on the driver.

Click the link to add information to this solution:
[575] I have motor control boards that have 4 pin input ( Step, Dir, EN, +5V) how do I connect this USB board?

There is no need to connect a stepper motor to a relay. The stepper motor driver controls the stepper motor completely.

Click the link to add information to this solution:
I have 8 wires wired to my driver in the right places. I need to know how to wire the relay Ken

Input to VFD:
240V Active - R
240V Neutral - S
Ground - E

Additional Information:

Click the link to add information to this solution:
HOW DO YOU CONNECT THE INVERTER TO AC?

If you are using shielded wire between the motor and driver, the shielded portion (the reflective jacket within the insulated portion of the wire) and any spare wires, or stranded wire should all be grounded and be inserted into the GND terminal on the driver.

Click the link to add information to this solution:
When using shielded wire from driver to stepper motor, where should I connect the shielding? Should it be ground on transformer or something/somewhere else?

I would suggest using the NPN proximity sensor for the Mach3 USB or the Pokeys57cnc. The proximity sensors have a top DC voltage limit of 30 volts, so it would be best to use the 24V power supply that is used to power the controller. Both controllers have a 24V power requirement, so that is convenient.

The blue wire of the proximity sensor is the GND wire and is connected to the 24V power supply's V- terminal. The brown wire is the positive wire and is connected to the V+ terminal of the 24V power supply. The black wire is the signal wire and is connected to the input terminal of the controller.

Click the link to add information to this solution:
How can I connect an inductive proximity sensor to the Mach3 USB controller?

You can go here to find the diagrams and instruction on connecting the parallel breakout board:

https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay

Also, please make sure to watch all of the electronics tutorial videos here:
https://www.buildyourcnc.com/CNCElectronicsandWiring.aspx

Click the link to add information to this solution:
how do I connect the parallel breakout board?

The motor is creating it's own EMF when you try to turn the shaft manually. When coils are connected (or not connected) to any circuit that is not powered can cause unpredictable results.

The motor freezing from just turning it by hand with no connection is surely the wires touching each other. This is actually how we test if a motor is good or bad. If the motor freezes when two of the wires are touching, that means the motor is functioning properly since the magnets are causing current to flow through that coil opposing the magnet.

Click the link to add information to this solution:
I cannot turn the shaft of my stepper motor. It not even connected to a driver