The USB Interface page: https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout

On this page, there is a datasheet that explains the connection schemes for the limit switches on step 1 of the instructions. The datasheet explains single and multiple switch configurations and parallel/serial connections schemes for the NO/NC (Normally Open/Normally Closed states).

If there is further information you need, please reply on this FAQ.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
Please provide detailed instructions on how to connect limit switches to CNC USB BOARD. I can not find instructions anywhere. I am new to cnc world and really need help. Thanks

Here is the information we have for the Planet CNC USB controller:

https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout-Planet-CNC

Click the link to add information to this solution:
Please advise correct wiring from PLANETCNC USB controller Mk3/4 to motor driver.

Connect the XD to the Dir, XP to the Step, and the 5V on the Mach3 USB controller to the +5V.

Click the link to add information to this solution:
[575] I have motor control boards that have 4 pin input ( Step, Dir, EN, +5V) how do I connect this USB board?

You can connect the 5V from the Mach3 USB controller to the 5V terminal on the driver, the XP to the Step terminal on the driver and the XD to the Dir terminal on the driver.

Click the link to add information to this solution:
[575] I have motor control boards that have 4 pin input ( Step, Dir, EN, +5V) how do I connect this USB board?

You will need PlanetCNC software for the USB breakout board and when plugging in the USB the computer should automatically recognize the board, however you can go into device manager to see if the USB terminal is working correctly.
The parallel breakout board; the USB is not a connection terminal rather than a power source, and the parallel port will be the communication terminal.
The items you will need for a water cooled spindle would be: water pump, silicon tubing(length desired by customer), a extension cord(from a hardware store(orange))(1 same gauge wire/length as extension cord).

Click the link to add information to this solution:
I am making my own CNC setup using all the electronics from your website and I have many questions. Please advise how to have my computer recognize the USB connection from my breakout board also I would like to use a water cooled spindle but I need to know the parts required for a 4x10 bed area used for woods and plastics

The step and direction terminals on the Mach3 USB controller are the terminals labeled XP, XD, YP, YD, ZP, ZD, AP and AD. The P is the pulse or step terminal and the D is the direction terminal.

The configuration for the motor outputs are already configured in the Mach3 configuration file that is available on that product page:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Click the link to add information to this solution:
On Mach3 USB the port number is 3 but i dont see the motor output pin numbers for the stepper side? could you please provide this for me? maybe a sketch of all the pin numbers the way Mach 3 sees them?

You will need a 24V relay to control mist using the Mach3 USB breakout board. The wiring diagram (link below) will show one of the output terminals (O1, O2, O3 or O4) connected to one of the leads of the relay. The other lead is connected to the V+ to complete the circuit. The other part of the relay is used as a switch to control the mist on/off.

Wiring diagram: https://www.buildyourcnc.com/Documents/Electric%20Wiring%20Diagram.pdf

Mach3 USB Breakout Board for CNC Routers: https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Click the link to add information to this solution:
How can I to connect a signal to turn on a mist in a USB board? Thank you

Did you install the Mach3 USB plug-in?

Make sure that you followed all of the steps and diagrams on the following page:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Click the link to add information to this solution:
ABSOLUTELY NOTHING WORKS. I HAVE ALL STRUCTURE AND MECHICAL PARTS OF THE BLACKTOOTH CUTTER DONE. HOWEVER WHEN WIRE UP STEPPER MOTOR TO DRIVER. THAT MACH 3 USB CONTROLLER BOARD, TRY JOG MOTOR, WORKS! PREVIOSULY HAD PLANET CNC BREAKOUT HOWRVER, ONLY MOVED MOTORS IN ONE DIRECTION COULDNT CHANGE IT. ANY HELP WOULD BE APRECIATED

This video should provide enough guidance to understand the PWM signal on the Mach3 USB controller:

Click the link to add information to this solution:
[575] Hello, I'm wondering if you can provide advice how to wire this USB board where for spindle I would like to use chinese servo motor and driver (TD3) - speed control mode. Especially how to connect - AVI, ACM and 10V (24V is clear). I am still not sure how to power on and off spindle itself. Thank you in advance. Vaclav

The parallel breakout board has the db25 connector for data and the USB connector for power. Connect the USB from the computer to the parallel breakout board so the breakout board will have 5V of power coming from the computer. The db25 connector (connector with the 25 pins) receive data signals for each pin from 1 to 17 and have respective numbered screw terminals, some for input and some for output (18 to 25 are gnd pins).

Click the link to add information to this solution:
Should I connect both the USB and the 25 pin connector of the parallel breakout board to the computer?

CP+ to COM
CP- to STEP
CP+ to CW+ (small jumper wire)
CW- to DIR

Additional Information:
If the driver does not have CP or CW labels, the CP is Step and the CW is Direction or DIR. If you connect the 5v to CP+ (or Step+) and CW+ (or DIR+) and the pin to CP- (or Step-) and another pin to CW- (or DIR-), then in software, the configuration for the step on that axis must be active low. Otherwise, if you connect the GND to CP- (or Step-) and CW- (or DIR-) and the pin to CP+ (or Step+) and another pin to CW+ (or DIR+), then in software, the configuration for the step on that axis must be active high.

Additional Information:
If you have a driver that is labeled pul, dir and ena: Pul+ is the Step+ and Pul- is the Step-. Pul is short for pulse. A pulse will create a step. Don't worry about the enable terminals.

On the x-axis, pin #2 can go to pul- and pin #3 can go to dir-. The 5v will go to pul+ and dir+. The configuration for each axis for step will be active low and toggle active low for the dir on each axis to make it go in the direction desired.

Additional Information:


Additional Information:


Additional Information:


Additional Information:

Click the link to add information to this solution:
HOW DO I WIRE FROM THE BREAKOUT BOARD TO DRIVER?

To implement a electronics combo to run you Proxxon MF70, you will need to find the correct drive components (ACME screw, linear rail, etc) and look into any specific modifications needed to your rig.
I would recommend the USB 3 Axis Large Motors Electronics w/ USB Interface Board.
Since the machine is metal, our larger motors would be highly recommended.

We have not done this conversion, through research is recommended.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
Hi I have a Proxxon MF70, I want to add 3axis stepper with controller and software by USB. Can you suggest a kit for me? Thanks.

If you want speed control, it is recommended to use the RS-485 connection on the VFD and use the control program such as Mach3 to communication serially with the VFD using this RS-485 connection.

If you would rather use a controller such as the PMDX-107 to simulate the effect of a potentiometer using the Aref, Aout and Agnd and the Rev/Dir and Fwd/Run terminals to control operation and direction, you can connect those to the VFD.

PMDX-107 Aout connects to the VI (analog voltage in). This is like the wiper on a potentiometer.
PMDX-107 Agnd connects to the ACM terminal on the VFD for Analog common.
PMDX-107 COM connects to DCM terminal on the VFD for Digital common.
PMDX-107 Fwd/Run connects to the FOR terminal on the VFD for Forward.
PMDX-107 Rev/Dir connects to the REV terminal on the VFD for Reverse.

Refer to your PMDX-107 manual to correctly configure your dip switch settings and make sure to calibrate (tweak) the speed control using the trimmer next to the terminals on the PMDX-107.

Click the link to add information to this solution:
I have the USB controller board and the 8825 step driver. I need a wiring diagram between the two. Specifically, what does the GND pin on the X-axis connect to? Also, what does the 5V pin on the driver connect to?

You can find a wiring diagram here:
https://buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout#prettyPhoto/2/

The CP terminal is wired to the step terminal on the 8825 step driver.
The CW terminal is wired to the direction terminal on the 8825 step driver.
The GND terminal connects to the GND on the 8825 step driver

The 5V connector on the driver simply powers the logic side of the chip and needs to connect to VCC pin on the keyboard jog.

Customer Response:
Thanks! Working now.

Click the link to add information to this solution:
I have the USB controller board and the 8825 step driver. I need a wiring diagram between the two. Specifically, what does the GND pin on the X-axis connect to? Also, what does the 5V pin on the driver connect to?

Since the Pokey57CNC outputs standard pulse and direction signals, you can use any stepper driver. So, you do not need to use the Postep driver to operate your stepper motors.

The Pokey57CNC control board is extremely feature rich and can be use to control very complex light or heavy CNC systems. Since most CNC system use high current drivers, the Pokey57CNC can be used with these systems.

Click the link to add information to this solution:
Do I have to use the Postep Driver with the Pokey57CNC usb/ethernet board. Can I use the Motor Driver (24-40 volts DC, up to 3.0 amps, microstepping from 1 to 1/64) With The Pokeycnc USB/Ethernet board.

blackToe requires a minimum cable length of of 15 ft for X, 17 ft for Y and 18 ft for Z for the redLeaf to be positioned at midpoint along the long axis and under the table. Each axis would need have 6 feet extra (form the midpoint)

Click the link to add information to this solution:
IF WE ASSUME DESIRE TO PLACE THE RED LEAF 6' AWAY FROM TABLE, HOW MUCH CABLE IS NEEDED CONNECT MOTORS ON TABLE ITSELF?

At this time we are working to release a new USB controller board that will be compatible with Mach4 software and do not have any immediate plans to update the Planet-CNC USB board.

Click the link to add information to this solution:
Are there plans to release a USB Controller to work with the Planet CNC Output Board for more advanced spindle control from within Planet CNC?

The wiring instructions for the USB controller can be found here: https://www.buildyourcnc.com/tutorials/tutorial-Electronics-USB-Interface-Wiring

Click the link to add information to this solution:
how to connect USB controller to the drivers. Any instructions/video other then html datasheet?

The board layout is different and the terminals have slightly different names, but the two boards function the same. The wiring diagram is the same for both boards. The plug-in driver for Mach3 is also the same, so you should not have a problem. If you do run into an issue, please let me know here and I will help you determine the problem.

Thanks

Additional Information:
Thank you for the assurance that the boards will function the same. You did not answer the primary question of wiring. The diagram shows a board with a 5V for each axis, the new boards have only 1 5V point on the axis side. In retrospect since this controller receives information and most possibly the 5V signal directly from the computer leading to the drivers. I will wire the X, Y and Z axis to the single 5V point and see what happens.

Click the link to add information to this solution:
received my mach 3 USB breakout board today. The layout of the board is different from your diagram which shows a 5V power slot for each axis. Do I wire the 5V slot with only one 5V wire from one of the drivers or perhaps wire all three 5V wires into the one 5 V slot. Please advise.