Yes, if you need a replacement part on your machine please call us at 281-815-7701.

Click the link to add information to this solution:
I have a blacktooth laser engraver. The Y Axis stepper motor needs to be replaced. Can you please provide me with the information I would need to replace this motor.

The formula for finding the steps per mm is found in the units itself. First, you mentioned that the motor is a servo. This needs to be clarified as a servo is different than a stepper motor. Some servos behave similar to a stepper motor, so I will continue with this in mind.

The formula is (steps/mm):

You need to find the steps. The stepper motor has a natural number of steps per a full revolution. This is typically 200 steps per revolution.

The driver for the stepper motor allows you to increase the number of steps per revolution by adding a specified number of steps between each step. For instance, if you set the driver to 1/4 microstepping, then instead of having 200 steps per revolution, you would have 200 x 4 = 800 steps per revolution.

So now we have the first part of the formula:

Steps / mm = (200 x 4) / mm

Lets determine the mm side of the formula:

You mention that the pitch is 0.5 mm. Check to insure that the lead is also 0.5 mm. This could be a multiple start lead screw where the pitch is different than the turns per mm. If in this case, that the 0.5 mm is the travel for one full revolution, then you can simply plug this into the formula as:

mm = .5 mm

Otherwise, determine how fat the travel is for one complete revolution.

Therefor, with what we know and the driver is set at 1/4 microstepping and the stepper motor has a natural step count per revolution at 200:

steps / mm = (200 steps x 4) / 0.5 mm = 800 steps / 0.5 mm = 1600 steps / mm

If your travel for one revolution is not 0.5 mm, then plug in your travel distance instead.



Additional Information:
i know about steps/mm calculation for stepper motor, because i am using servo motor that why i asked about that. please tell for servo motor.

Additional Information:
because its my first time with servo motor i have no idea about calculation of parameter with servo.

Additional Information:
Have you attempted to contact the manufacturer or seller of the servo? We typically respond to customers of our products on this customer service area, unless we have extensive knowledge of the subject and can answer the question efficiently.

Additional Information:

Click the link to add information to this solution:
hello there, i am using servo motor for my X and Y Axis but i dont know how to calculate steps/mm for that, the lead screw i am using is have pitch of .5 mm. please helpme on this i have done everything only this point is pending.

This is most likely a wiring issue. I would disconnect all of the power to the drivers and reconnect one at a time to isolate the problem.

Additional Information:
that was not helpful. I already did that way before submitting this question. there are not that many wires here and I have already rewired this a few times. I actually think its a software or interface board issue because it does work sometimes but then trips (possibly a amperage / voltage issue) I am using the interface board that has a parallel port and usb for 5V. are there different settings that I need to setup?

Click the link to add information to this solution:
I'm using the big 651oz in stepper motor for X and Y and the smaller 325 for the z and X and Y keep tripping when I try to tune the motors on Mach3 but Z seems to work. I have to turn power on and off to reset....is this a wiring issue?

It is usually best to mount the motor in a way so it is spinning clockwise to avoid confusion.

Additional Information:
ok, but lets say the motors turn clockwise. if you mount it to ether side of the y axis it will pull to that side so what are the correct positions of the stepper motors. is it the left side or the right side of the y axis and also is it the front or back of the x axis?

Additional Information:
cw250 with mach3 controller

Click the link to add information to this solution:
What side of the x and y axis do you mount the stepper motor to? If it does not matter what side, do I have to change something in mach3?

The drivers have quite a bit of protection, so you probably won't ruin anything. You motors are jumping and that is just the motors engaging from getting power from the power supply.

There could be many reasons your motors don't turn. Consider these troubleshooting tips:

- If you are using our parallel breakout board, make sure that the step pins are set for active low (config -> Ports and Pins -> Motor Outputs -> the steps pins should be enabled and set active low)

- The parallel breakout board is powered (connect the USB to the computer using a USB cable)

- In Mach3, make sure you have jog enabled (a little green button at thelower middle of the page in the program run screen).

Additional Information:


Additional Information:
DS26

Click the link to add information to this solution:
My stepper motors stopped working all of a sudden. Mach 3 is running fine, just no signals getting to the motors. The lights on the motor drivers began blinking erratically when this started. Any advice where a problem like this can come from would be greatly appreciated.

You would use a combination of bearings and collars to prevent your lead screw or rod from being able to move back and forth. Without it being able to move back and forth, you shouldn't have the couplings coming apart, because the motor is solidly mounted and unable to move as well.

I will try to draw a picture using symbols, with a key to define what each part is.

--CB|--------------|BC}{M

- = Lead Screw or Rod
C = Collar
B = Bearing
| = Wood, the frame of your machine
}{ = Coupling
M = Motor

On the example above you could replace the collar on the motor side with one half of the coupling, putting it right upside of the bearing to hold it in place instead. Like this:

--CB|--------------|B}{M

You could also place the bearings on the inside as follows:

----|BC----------CB|--}{M

Click the link to add information to this solution:
can you please specify how to connect the collar/nut and bearings to prevent the axial movement of lead screw. Do I have to put that next to the stepper motor /coupling assembling or on the other side where the lead screw comes out. Or is there any way I can make the flexible coupling rigid so it does not come out of the middle spider?

We will provide shim washers as a part of machine assemblies, but when purchasing lead screw and bearings, the shim washers must be purchased as well. Please give us a call and we can send them out.

Click the link to add information to this solution:
I just ordered a 1/2" lead screw and bearings, etc. But I don't see any 1/2" shim washers for those bearings. If you have any, please toss 8 of them in the shipment and I'll gladly reimburse you.

We attempt to provide as many services as possible to fit the needs of the CNC community. For a quote on a custom job, please email customerservice@buildyourcnc.com and we will be happy to assist you.

Click the link to add information to this solution:
I bought longs motor nema 34 stepper motor with 4 powers supply and dm860 from ebay, would you be interested in doing all the wiring for me? I pay you for you time

That depends on a few factors. In most cases, three 3.0 amp motors and drivers will not exceed 8.8 amps of available current. All of the motors would need to be at full torque to reach the 9 amps (3x3). This depends on the mechanical method you are using for each motor, and how you are using the machine. In most cases, only two motors are moving at a time (i.e. 3D carving where the X and Z are moving simultaneously and the y only moves to go to the next row). In traditional cutting profiles, only the x and y are moving simultaneously and the z-axis moves at the location it needs to start cutting the next layer.

With that said, it is ok to add an extra power supply if you feel you need more available current.

Click the link to add information to this solution:
[810] Is this a closed loop motor? What is the recommended driver and power supply for this stepper? Would you recommend using one power supply per motor pair or one power supply per motor?

The pin number for the PWM output for the Mach3 USB controller is pin #3 and O3 (out3). This setting should be specified in the motor outputs tab in the ports and pins dialog box for the spindle signal line.

Click the link to add information to this solution:
https://www.buildyourcnc.com/images/mach3USBCardWiringdiagram-800.jpg I would like to know the settings such as the pin number for 0 to 10V output of AVI+ and AVI- as in this wiring diagram.

We may be able to source those motors. Curious, the 6000 oz-in motor is pretty big. Do you mind explaining the application of the CNC machine and the structure that would require the large motor?

Additional Information:
The largest motors we can offer is 3900 oz-in without any mechanical help. 6000 oz-in can be resolved by mechanical means as an alternative.

Click the link to add information to this solution:
I am converting a 12x36 lathe over to CNC, I am interested in a 2 axis kit. I would love one stepper motor to be no smaller than 1200oz. , and another at 6000z. Is this something that you could offer? I have two other cnc machines but this is my first converstion on my own.

Connecting the limit switches on the redLeaf use the input pins on the parallel breakout board. Here is a link to the wiring diagram for that parallel breakout board.

https://buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay#prettyPhoto/2/

The connection is simple. Just create a circuit from ground to the pin. When the pin is engaged, the circuit is closed (using normally open on the switch). Use mach3's autoset to automatically set the pin for the limit or home setting.

Click the link to add information to this solution:
Do you guys have any videos showing how to connect limit switches to a redleaf? If not, could you please make one? I looked at the diagrams on the limit switch page but I don't understand them.

Depending on the probe that you have, you should have two wires coming from the probe. One of those two wires will need to be connect to an input pin as shown in this wiring diagram (the diagram show the probe connected to pin I4):
https://www.buildyourcnc.com/Documents/Electric%20Wiring%20Diagram.pdf

The other pin is connected to V-. Please make sure that you have 24V connected to the V- and V+ on that side of the Mach3 USB board.

The way the probe works is when the probe is in contact with an object, a specific spring mechanism will cause the input pin to be connected to the V- (close the circuit). When Mach3 senses an active low on the input pin, mach3 knows that the probe has made contact (closed the circuit).

If your probe is used as a Z-Axis zero plate, then the concept is the same, but the end mill is connected to V- and the plate is connected to the input pin. If the plate comes in contact to the end mill, then the circuit is closed and mach3 will sense an active low on the input pin.

Click the link to add information to this solution:
Mach3 USB interface board. Could you please give me the correct wiring configuration for tool prob?

Generally, you’ll need to check what control software will need to be used with the CNC router. Our machines use industry standard electronics and control software that is nonproprietary so you can use just about any software out there with our machines.

Specifically, what software are you planning on using?

Additional Information:
dear Sir,
I'm searching for the best one,I think that I have to learn more about that in order to be able to make the right decision.

Additional Information:
If you are using a computer running Microsoft Windows, then I would recommend using Mach3 or Mach4. If you prefer Linux, then LinuxCNC is the best control software in my opinion.

Click the link to add information to this solution:
I'm searching for a desktop cnc, could you tell me please if any software I may choose could be compatible with all desktop cnc machine or I have to check the compatibility before ?

Our MAch3 USB interface boards can be located here:

https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Click the link to add information to this solution:
I am interested in the 3 axis combo USB option. I notice you endorse the Planet-CNC for use with this but will Mach3 interface well with the USB beak out Board?

Our MAch3 USB interface boards can be located here:

https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

Click the link to add information to this solution:
I AM INTERESTED IN THE 3 AXIS COMBO USB OPTION. NOTICE YOU ENDORSE PLANET-CNC FOR USE WITH THIS BUT WILL MACH3 INTERFACE WELL BEAK OUT BOARD?

can not get the limit switches to work on the usb controller board

Additional Information:
Wiring the motors to the drivers for our 8 wire motor is probably the 425 oz-in NEMA 24 stepping motor. Here is the URL for the diagram of the motor:
https://www.buildyourcnc.com/Documents/PN.SM60HT86-2008BF-U%20(inhouse%20PN.60BYGH303-13)%20(1).pdf

Wire it in bipolar parallel as specified on the data sheet.

Here is the URL for the motor to check if it is the same that you purchased.
https://www.buildyourcnc.com/item/electronicsAndMotors-nema24-425ozin

The USB mach3 board URL is here:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

The wiring diagram is on that page and instruction on how to use it.

Click the link to add information to this solution:
I recently purchased the 3 axis mach3 usb kit the motors have 8 different colored wires (no stripes on wire just solid color) all instructions have different colors. cannot find tutorals. does the mach 3 hook up same as planet? please let me know where I can find wiring diagram to hook up mach 3 usb BOB and motors (I am new to this kind of work projects)

That is correct. We send the fewer ribs than could be fastened within the gantry. One reduction of a rib will provide more space for the motor at the midpoint of the gantry and at the other side of the gantry (opposite the motor) can be reduced to provide more space to work with the coupling.

Click the link to add information to this solution:
I'm assembling the gantry for a 5x10 greenbull and noticed that there are 9 spaces for torsion spacers but only 7 in the kit. Should I just space them out on the right side behind the motor?

Can you send me a link to the digitizer you are using?

Click the link to add information to this solution:
Hi my names is Minh Truong I would like to said thank you very much for your video I got the system mach3 working fine but one thing I can NOT set and config the digitizer on the board IN4 I am not sure how to setup because in the Mach3 pin 14 for digitizer Please shoe me hoe to set it up for the digitizer.