If you received fewer parts than is called for in the instructions, we will send the proper parts to you. Please call us to have these parts sent to you.

Click the link to add information to this solution:
I ordered the blacktooth laser cutter, there were only 4 red spade terminals, but the instructions pictures show that there should be more and would include blue spade terminals

The Mach3 USB controller will light a solid red light when the controller is properly connected to the computer, and mach3 is in the ready mode (reset pressed to engage the machine). When an arrow key is pressed to move an axis, the red LED will blink rapidly showing there is communication to the controller. If it does not blink rapidly, then check the motor output and confirm that the axes are enabled. Also, confirm you are in jog mode (located in the program run tab). You can also try using the built-in MPG by pressing the TAB key and clicking on the axis letters to move the axes.

Click the link to add information to this solution:
I connected my intrface board as per the diagram but I don't get a blinking light. I get a solid red light. What could cause this?

The solid red light is a condition where the Mach3 USB controller is successfully connected to the computer and is communicating to Mach3.

Click the link to add information to this solution:
I connected my intrface board as per the diagram but I don't get a blinking light. I get a solid red light. What could cause this?

The greenBull instructions are found on our website. Each machine has a page, which you can locate by clicking on "CNC Machines" from the left hand menu and choosing the particular machine you have. Scroll to the bottom of that machine page and you will find complete instructions. The page for the greenBull 5X, for example, is : https://buildyourcnc.com/Item/cnc-machine-greenBull-v4-5X

The redFly is typically sold with motors already wired to conductor cable with 4-pin connectors; these need simply to be plugged into the control box. There is no soldering required. If you have a different configuration, please contact us directly at techsupport@buildyourcnc.com with information about your specific application (and a photo, if possible) and we will be happy to provide you with further guidance.

Click the link to add information to this solution:
How do I know how to hook up the red fly? What color wires do I solder on which pin of the connectors? Was there suppose to be any instructions that came with it, or the entire greenbull for that matter?

You will definitely want to adjust your debounce setting in mach3 if your emergency or limit switch is engaging.

Additional Information:
Did you ever fix this issue? I am having the same problem.

Additional Information:
Did you ever fix this issue? I am having the same problem.

Additional Information:
Did you ever fix this issue? I am having the same problem.

Additional Information:
Did you ever fix this issue? I am having the same problem.

Additional Information:
Did you ever fix this issue? I am having the same problem.

Additional Information:
Did you ever fix this issue? I am having the same problem.

Additional Information:
Did you ever fix this issue? I am having the same problem.

Additional Information:
Did you ever fix this issue? I am having the same problem.

Additional Information:
Did you try changing the denounce setting?

Additional Information:
Meant to say denounce.

Click the link to add information to this solution:
When I start my spindle I get a emergency stop in Mach 3. I have run shielded cable and it is grounded at the VFD it is wired per you site instructions. any idea what to check

For our parallel breakout board (https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay#prettyPhoto/2/) the schematic will show the connections going from the BB to the drivers. The parallel breakout board uses the 25 pin parallel connection to communicate from the computer to drivers, and the USB is used to power the main-board itself, supplying 5V.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
The electronics package I just bought from you (Book Build) is different from your wireing diagrams and video tutorials. Is there an updated wiring diagram available? Is the USB port on the breakout board connected directly to the computer USB to supply 5 volts? Thank you.

Depending on the board you are currently using, either the Parallel or USB interface board.
The parallel interface needs the USB cable for power(5v) and the parallel cord for communicating from the board to the computer and vise versa.
The USB interface board, will need a keyboard jog header made to fit the 12 pin connector(2 x 6). Making this connector will allow you to be able to wire it to a external panel, where you can use it to jog your machine rather than using the onscreen jogging.


Please contact customerservice@buildyourcnc.com for further assistance.

Click the link to add information to this solution:
I buy a four axis kits and i connect all parts respecting the plan. The USB connector is using for électric alimentation of the When I want to activate the engine with the computer keyboard , nothing works. The current 5VDC since green light is on but when I check with a voltmeter each pin , then I see that there is no current. What's happening?

Most motherboard do contain parallel ports, but the port connector may not be at the back (in the section where external connectors will be connected). Instead, the motherboard may contain an LPT ribbon connector on the actual face of the motherboard (usually along one of the edges). You will need a ribbon connector to a DB25 female connector.

If your motherboard does not contain an LPT header on the motherboard, you can purchase a parallel printer adapter that plugs into one of the PCI slots. The price of the adapter is very inexpensive and sometimes is actually less costly than the actual ribbon connector.

Click the link to add information to this solution:
As I am building my 20" x 24" laser engraver cutter, I notice that there is no parallel port on the onboard computer and I have the parallel breakout board any answers?

The driver's LED serves to indicate a fault condition. The driver chip has built in protection for overheating and over current. If the LED is on, most likely, the driver will stop until the condition is resolved. If you see the LED on, adjust the vref trimmer. First, connect a multimeter to the pads just next to the trimmer potentiometer and adjust until the voltage is lowered a bit. Alternatively, even though the PCB contains a vast amount of thermal vias and a relatively large ground plane connected to the belly of the driver, there still may be a need to cool the driver chip using a small heat sink. Do this only if you are not satisfied with the performance of the motor at the torque require.

Click the link to add information to this solution:
Under what conditions should the LED on the 3d printer driver be lit when the driver is connected to the MB?

Did you connect the USB connector to the breakout board?

Additional Information:
YES I CONNECTED THE USB TO THE BREAKOUT BOARD

Click the link to add information to this solution:
I connected the electronics (for 2 x 4 feet) that I ordered from you. But how do I check if I connected all the wiring properly. There is neither any light on motor drivers nor on breakout board. And the motor shaft also does not move before and after the power supply is given.

Youmay be able to find an adapter for your cable, or even a new cable, locally. This is the cable we sell that will work, https://www.buildyourcnc.com/item/electronicsAndMotors-cable-wire-db25-male-male

Click the link to add information to this solution:
The female 25 pin socket on my computer has to be connected to a similar socket on the breakout (parallel) board which came with my Blacktooth. Do I need a DB25 to DB25 cable, if such a thing exists? The cable I have is male to female.

It seems to be getting some kind of interference or a short within the wiring or communication, try jogging the motors in the software without anything wired to the board. Then add one motor at a time to see if there is a short within your wiring or a faulty driver/motor.
If the USB breakout board continues to move the x-axis with no motors or driver wired to it, please email customerservice@buildyourcnc.com for a replacement or further troubleshooting.

Click the link to add information to this solution:
I AM USING USB BREAKOUT BOARD WITH PLANET-CNC SOFTWARE. WHEN ENABLE JOGGING KEYBOARD X AXIS STARTS TO MOVE BY ITSELF (WHETHER CONNECTED OF NOT). PRESS STOP - IT STOPS FOR A MOMENT AND THEN AGAIN. WHAT COULD THAT BE? TRIED REINSTALL SOFTWARE DID NOT HELP.

By USB power do you mean the USB board? or do you mean that it is powered through USB but you have the parallel breakout board?


Additional Information:
I was referring to USB Board. Thanks for responding but that issue was resolve. I noticed that Mach 3 was downloaded twice. I copied and pasted RNR file to second copy of Mach 3 and motor runs properly. Should I remove one copy of Mach3 so there is only one? Seems like that could cause confusion. Thanks

Additional Information:
I was referring to USB Board. Thanks for responding but that issue was resolve. I noticed that Mach 3 was downloaded twice. I copied and pasted RNR file to second copy of Mach 3 and motor runs properly. Should I remove one copy of Mach3 so there is only one? Seems like that could cause confusion. Thanks

Additional Information:
I was referring to USB Board. Thanks for responding but that issue was resolve. I noticed that Mach 3 was downloaded twice. I copied and pasted RNR file to second copy of Mach 3 and motor runs properly. Should I remove one copy of Mach3 so there is only one? Seems like that could cause confusion. Thanks

Click the link to add information to this solution:
How do I know if my board for usb is set up correctly. When i do driver test says no driver found. RnR when jogged motion file is in plugins folder. red light is blinking on board but no motion

By USB power do you mean the USB board? or do you mean that it is powered through USB but you have the parallel breakout board?


Additional Information:
I was referring to USB Board. Thanks for responding but that issue was resolve. I noticed that Mach 3 was downloaded twice. I copied and pasted RNR file to second copy of Mach 3 and motor runs properly. Should I remove one copy of Mach3 so there is only one? Seems like that could cause confusion. Thanks

Additional Information:
I was referring to USB Board. Thanks for responding but that issue was resolve. I noticed that Mach 3 was downloaded twice. I copied and pasted RNR file to second copy of Mach 3 and motor runs properly. Should I remove one copy of Mach3 so there is only one? Seems like that could cause confusion. Thanks

Additional Information:
I was referring to USB Board. Thanks for responding but that issue was resolve. I noticed that Mach 3 was downloaded twice. I copied and pasted RNR file to second copy of Mach 3 and motor runs properly. Should I remove one copy of Mach3 so there is only one? Seems like that could cause confusion. Thanks

Click the link to add information to this solution:
How do I know if my board for usb is set up correctly. When i do driver test says no driver found. RnR when jogged motion file is in plugins folder. red light is blinking on board but no motion

What laser controller model number do you have?

Additional Information:
Hey - the model number on the laser controller is
AWC708C
S/N:708014243

Additional Information:
Thanks for the model number. I am going to fabricate the parts and put it together myself to see the issue. We made this modification to the blackTooth laser cutter to better house the new laser controller that we wanted to add to the laser, but that may have been for the AWC608. If there is an issue with my assembly, we will create a new part that will correct the issue and send it to you.

Additional Information:
Thank you for the update!

Additional Information:
Have you had a chance to duplicate the issue yet?

Click the link to add information to this solution:
There are no instructions on how to assemble the laser control unit housing that came with my 40w blacktooth laser kit. How can I get instructions for how to assemble the control interface housing? Every configuration I try blocks the wire connection ports.

The instructions to connect the USB CNC Interface for the blackTooth Laser Cutter and engraver can be found on instruction #18 on thispage: https://www.buildyourcnc.com/blackToothLaserCutterAndEngraver.aspx

Click the link to add information to this solution:
Are there any instructions for use the USP breakout board for a CO2 laser?

The datasheet for the parallel breakout board is here:
https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay#prettyPhoto/2/

The datasheet for the USB interface is here:
https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout#prettyPhoto/2/


Additional Information:
20

Click the link to add information to this solution:
I need wiring instructions for the breakout board you sent yesterday. It is not like the one in the videos and I don't know where to connect the 5V. No data sheet or anything.

Depending on the type of motors and connection type, you could adapt your motors to work with our electronic packages, but you will receive additional motors since our kit is complete.

Now you will have to take into affect the actual motors you have and compare or get accurate replacements(Ex. our 425 oz motor(1/4" input shaft) will have to be same size or similar entry holes)

Your Controller board will be the major issue, due to its wiring and processing manner, you can view the connections for our breakout boards to compare with yours! (parallel: https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay#prettyPhoto/2/)(USB: https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-USB-Controller-Breakout#prettyPhoto/2/)
Email(customerservice@buildyourcnc.com for further help)

Click the link to add information to this solution:
I purchased the original instructions about 3 years ago and successfully built that device. Now I am looking at the 13X36 Bluechick base kit. Will all my original electronics work with the new kit? Is there a parts list that you could send me for the 13x36 Kit?

The 800 series of Porter Cable routers all have the same diameter; therefore, you can purchase the latest model of that series and you should be fine with the fit for our router mounts.

Click the link to add information to this solution:
Which Porter Cable router should I purchase? The instructions say the 800 series, but I can't purchase an entire series, and don't know the difference between them.