The collet in the 1.5 kW spindle is an ER-11 and cannot reach the 1/2" size. I would consider the 2.2 kW spindle instead.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
WHAT SIZE COLLET IS IN YOUR 1.5 KILOWATT SPINDLE?

If this endmill/bit has a shaft of 1", plus the cut length the ER-20 collets we provide will work without any issues.

If the shank goes into the 1/8" ER20-collet at least .773 (safety margin), it will work without any problems. (This is only for the 1/8" ER20-collet)

Click the link to add information to this solution:
Can bits with shank length of 1" be used in the 1/8" ER20 collet?

The total length of the brush strip for a 2.2kW spindle would be 17 1/4" inches.

Additional Information:
20

Click the link to add information to this solution:
LENGTH OF THE BRUSH STRIP FOR SPINDLE 2.2KW

It is not necessary to connect the spindle VFD (Variable Frequency Drive also called an Inverter) to the computer or CNC motion electronics. The VFD can be controlled independently using the control panel on the VFD. The control panel has the ability to control all aspects of the spindle including Speed, Torque, limits, etc. However, you can connect the VFD to the computer so the CNC control program can control the spindle during the CNC Machine operation. You will need to connect the VFD to the computer via a serial conection (in this case, it is the RS-485 protocol).

The following are instructions on how to connect the VFD to Mach3 via this RS-485 serial connection.

The first thing you will need is the dynamic link library to pair with mach3 called the Huanyang VFD Mach3 PlugIn. You can find this file at the mach3 support forum here: http://www.machsupport.com/forum/index.php/topic,14182.0.html

You will also need to download the Microsoft .net 3.5 framework and install it: https://www.microsoft.com/en-us/download/details.aspx?id=21

Follow the pdf that comes with the library file, but here is a synopsis of what you need to do (I also added a lot more information that may be useful during this process as the manual does not cover the main connections that need to be done):

You will need to program your VFD so that it knows how to communicate with mach3 and the computer (go into the programming mode of the VFD and change these parameters):
- PD001 - value 2 - Enables with communication aspect of the VFD
- PD002 - value 2 - Enables frequency control from the communcations port
- PD163 - value 1 - VFD address
- PD164 - value 1 - Baud rate of 9600 (speed of the communication)
- PD165 - value 3 - 8N1 RTU - 8 bits (that's the size of the word that gets communicated), N (No parity or no error checking) and 1 (1 stop bit)

Copy the dll file to the PlugIns folder of mach3.

Connect the RX and TX lines to your computer. There are a couple ways you can do this, but the recommended way would be to use an FTDI USB device which converts a USB to a serial com port. The device will have Rx and Tx connectors to connect to the VFD terminals with the same labels. This method is recommended since serial ports are not as common in computers these days.

Next, you will need to configure mach3 to use the plugin library. Start mach3 and click on Menu -> config ->Config Plugins. Enable the new plugin by clicking on the red cross on the left column next to the plug in. Restart mach3 after doing this.

No you need to configure mach3 to use the HuanyangVFD plugin. Go to the ports & pins configuration and select the spindle setup tab. Make sure that the Disable Spindle Relays checkbox is unchecked. We don't want mach3 to output a signal for a relay since the spindle will start up and turn off within the VFD and not from an external relay.

Next, go to the HuanyangVFD settings by clicking on Menu -> plugin control -> HuanyangVFD. Set the parameters to the same settings you put into the VFD programming. The com port will be shown as new hardward when you plug in the USB FTDI device. A little bubble will be displayed at the bottom right where it will notify you that a new device is being installed (be patient while windows assigns a com port). Alternatively, you can use the windows device manager to see which port was set for the new USB FTDI device). You may need to restart mach3 several times until you get the correct information displayed in the PD001 and PD002 fields. When the com port is correct and the other parameters, like baud and VFD address is the same as you entered in the programming, then the PD001 and PD002 will show the number 2, otherwise, a 99 will appear which means that communication was not successful.

You can now control the on/off and RPM of the spindle using the RS485 communication between mach3 and the VFD.

Additional Information:
The question was how to connect the spindle to the redfy. I did not receive a VFD.
I have the redFly system and a 2.2kW Spindle - 110V how do i connect the spindle?

Additional Information:
If you received a spindle without a VFD, please contact us asap. Our spindle will not work without a VFD.

Additional Information:
Hi, how is this setup in mach4?

Click the link to add information to this solution:
I HAVE THE REDFLY SYSTEM AND A 2.2KW SPINDLE - 110V HOW DO CONNECT SPINDAL?

That is difficult to tell at this time. Right when we get them in, they go fast. These items come from China and the units are shipped in via freight on ship, so there are many factors on the delivery such as weather.

Click the link to add information to this solution:
When will the 2000 mm HIWIN Spec Linear Guide rail be available?

We don't have cad models of the HIWIN blocks, but you can find the models on McMaster.com. They have can drawings and models for most of these types of parts.

Click the link to add information to this solution:
DO YOU HAVE CAD AVAILABLE FOR THE HIWIN GUIDE BLOCKS SELL AND RAIL?

We don't have cad models of the HIWIN blocks, but you can find the models on McMaster.com. They have can drawings and models for most of these types of parts.

Click the link to add information to this solution:
DO YOU HAVE CAD AVAILABLE FOR THE HIWIN GUIDE BLOCKS SELL AND RAIL?

U - Pin1
V - Pin2
W - Pin3
Pin4 Dead

Additional Information:
My home made cnc is a big problem with my NC connection. When in start my spindle it will be gone wrong. It will be limith switch problem anytime. Need help thanks.

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
WHAT ARE THE OUTPUT INVERTER (VFD) CONNECTIONS TO SPINDLE?

The spindle inverter (VFD) will run on a 220V (or between 170V-250V) power source with either 50Hz or 60Hz.

Click the link to add information to this solution:
DOES THE SPINDLE RUN ON A 50HZ POWER SOURCE?

U - Pin1
V - Pin2
W - Pin3
Pin4 Dead

Additional Information:
My home made cnc is a big problem with my NC connection. When in start my spindle it will be gone wrong. It will be limith switch problem anytime. Need help thanks.

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
HOW DO YOU HOOK UP THE SPINDLE TO INVERTER?

Change PD001 Source of Run Commands to '1'
Change PD005 Max operating frequency to 400hz
Change PD004 base frequency to 400hz
Change PD003 Main frequency to 400hz
Change PD006 Intermediate frequency to 2.5
Change PD008 max voltage to 220v
Change PD009 Intermediate voltage to 15v
Change PD010 Min voltage to 8
Change PD011 frequency lower limit to >100hz (120hz to start)
Change PD142 7 Amps
Change PD143 2
Change PD144 3000

Note: PD001 had to be changed back to 0 to allow for keypad control.
Note2: I had to reverse U and V to get the spindle to go forward in FWD. (reverse any two wires, u&v or w&v for example)

Additional Information:

Click the link to add information to this solution:
HOW DO YOU SETUP THE SPINDLE INVERTER VFD?

Yes, our porter cable collets and nuts will fit the porter cable 7518.

Additional Information:

Click the link to add information to this solution:
HAVE PORTER CABLE 7518 ROUTER ON MY CNC AND WOULD LIKE TO KNOW IF YOUR ER20 COLLET NUT, FOR THE CABLE, WILL FIT ROUTER.

U - Pin1
V - Pin2
W - Pin3
Pin4 Dead

Additional Information:
My home made cnc is a big problem with my NC connection. When in start my spindle it will be gone wrong. It will be limith switch problem anytime. Need help thanks.

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
HOW DO YOU HOOK UP THE VFD TO SPINDLE?

Change PD001 Source of Run Commands to '1'
Change PD005 Max operating frequency to 400hz
Change PD004 base frequency to 400hz
Change PD003 Main frequency to 400hz
Change PD006 Intermediate frequency to 2.5
Change PD008 max voltage to 220v
Change PD009 Intermediate voltage to 15v
Change PD010 Min voltage to 8
Change PD011 frequency lower limit to >100hz (120hz to start)
Change PD142 7 Amps
Change PD143 2
Change PD144 3000

Note: PD001 had to be changed back to 0 to allow for keypad control.
Note2: I had to reverse U and V to get the spindle to go forward in FWD. (reverse any two wires, u&v or w&v for example)

Additional Information:

Click the link to add information to this solution:
HOW DO YOU SETUP THE SPINDLE INVERTER?

The greenlean requires 56 feet of 1/4 Inside Diameter and 3/8 Outside Diameter silicon tube for the spindle.

Additional Information:
20

Additional Information:
20

Click the link to add information to this solution:
HOW MUCH SILICONE TUBE DO I NEED FOR A GREEN LEAN TO CONNECT THE SPINDLE

U - Pin1
V - Pin2
W - Pin3
Pin4 Dead

Additional Information:
My home made cnc is a big problem with my NC connection. When in start my spindle it will be gone wrong. It will be limith switch problem anytime. Need help thanks.

Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
HOW TO CONNECT THE SPINDLE INVERTER?

Input to VFD:
240V Active - R
240V Neutral - S
Ground - E

Additional Information:

Click the link to add information to this solution:
WHAT ARE THE SPINDLE INVERTERS (VFD) INPUT AC CONNECTIONS FROM WALL OUTLET?

The spindle is quieter and has more consistent torque (It doesn't get "bogged down" when it starts cutting into material). It can be used with collets of varying sizes (not restricted to imperial sizes). It is water cooled and so it does not blow air downward to cool the spindle like the router does. The spindle is also machined with much higher precision than typical routers and will have a much longer life.

Click the link to add information to this solution:
WHY SHOULD I BUY THE SPINDLE?

Yes, all of the spindles come with collets. The collets have a 1/4" (6.35mm) bore for end mills that have a 1/4" shank. The ER specification is different for the 1.5kW (ER-11) and the 2.2kW (ER-20).

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
I’M LOOKING TO PURCHASE SPINDLE AND VFD WAS CURIOS IF THE SPINDLES COME WITH COLLETS SO WHICH ONES?