[ Log In ]
[ Register ]

Question #: 146

Question: How can I remove the text enhance malware adware hijacker software?

Current Solution

If you would like to remove the malware or flash adware called text-enhance, follow the steps on this wab page: http://botcrawl.com/how-to-remove-text-enhance/

Respond:

Other Possible Solutions to this Question

  • How do I remove Text Enhance?

    If you would like to remove the malware or flash adware called text-enhance, follow the steps on this wab page: http://botcrawl.com/how-to-remove-text-enhance/

    Click the link to add information to this solution:
    How do I remove Text Enhance?

  • HOW CAN YOU ENHANCE THE BLACKTOOTH LASER CUTTER?

    Temperature probe monitor. Very valuable. This keeps you up to date on your coolant temperature levels.

    Voltage meter. This will tell you the exact level of voltage/power you are running telling the laser to run at instead of an arbitrary mark on a drawn wheel around your POT.

    Ammeter sensitive to 1mA. This will be sure your not over driving your tube and reducing it's life significantly.

    Hour meter. This will tell you exactly how long your system has been 'on' giving you a more accurate bead on the length of your tubes life.

    Exhaust fan upgrade. The current fan included is 100CFM. You can buy 120mm fans that push 250CFM and I have included a guide on how to go about doing this here. http://buildyourtools.com/phpBB3/viewto ... 8cdd1802bf

    To push the exhaust fan even further, if you have the room/power, I would highly recommend investing in a 600+ CFM "Dust Collector" system. 250CFM is still not suffice to draw all the smoke that can come off of 3mm or 1/8 MDF cutting job.

    A cutting surface. I bought myself a aluminum 'egg crate' mesh from my local HVAC company. They are used a cover for fluorescent lights and work great for low impact cutting surface. They come in 4'x8' sheets and are easily cut to fit. The other side is if you can find a steel honeycomb cutting bed to fit. These can be quite costly or fairly affordable depending where you are looking. The benefit of a steel honeycomb is you can use high power magnets to hold material down.

    Click the link to add information to this solution:
    HOW CAN YOU ENHANCE THE BLACKTOOTH LASER CUTTER?

  • Whereb can I find directions on how to install the Mach3 USB board with Mach 4 software? I do not have a parallell port.

    You can find instructions for the Mach3 USB here:
    https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

    You will probably need to use the Mach3 USB board with Mach3. We have not tested the Mach3 usb card with Mach4.

    Click the link to add information to this solution:
    Whereb can I find directions on how to install the Mach3 USB board with Mach 4 software? I do not have a parallell port.

  • How can I control my VFD using Mach4 cnc control software?

    The best way to determine how to control your VFD using Mach4 is to read the MAch4 manual found here:
    http://www.machsupport.com/wp-content/uploads/2014/05/Mach4%20Installation%20Manual.pdf

    You will find that there a a few ways to control the spindle/VFD on your CNC machine or CNC Router.
    - The first and easiest is to have your VFD's power controlled by a relay. This will allow your spindle to have on/off control through Mach4 with an output pin.
    - The second is to have a controller output a DAC voltage between 0-10 volts to control speed on the VFD/Spindle. There is a termial on the VFD to receive this signal line. The controller will also have an output that outputs a high or low and that can control the on/off on the VFD.
    - The third, and more difficult of the three methods is to use a USB to Serial adapter (USB to USART or RS-485). The Computer plugs into the adapter using a USB cable and the adapter uses the RX/TX to connect to the VFD's terminals for communication. This will provide a great amount of control. Mach4 will need a plug-in to make this option work.

    Click the link to add information to this solution:
    How can I control my VFD using Mach4 cnc control software?

  • HOW CAN ENHANCE THE BLACKTOOTH?

    Temperature probe monitor. Very valuable. This keeps you up to date on your coolant temperature levels.

    Voltage meter. This will tell you the exact level of voltage/power you are running telling the laser to run at instead of an arbitrary mark on a drawn wheel around your POT.

    Ammeter sensitive to 1mA. This will be sure your not over driving your tube and reducing it's life significantly.

    Hour meter. This will tell you exactly how long your system has been 'on' giving you a more accurate bead on the length of your tubes life.

    Exhaust fan upgrade. The current fan included is 100CFM. You can buy 120mm fans that push 250CFM and I have included a guide on how to go about doing this here. http://buildyourtools.com/phpBB3/viewto ... 8cdd1802bf

    To push the exhaust fan even further, if you have the room/power, I would highly recommend investing in a 600+ CFM "Dust Collector" system. 250CFM is still not suffice to draw all the smoke that can come off of 3mm or 1/8 MDF cutting job.

    A cutting surface. I bought myself a aluminum 'egg crate' mesh from my local HVAC company. They are used a cover for fluorescent lights and work great for low impact cutting surface. They come in 4'x8' sheets and are easily cut to fit. The other side is if you can find a steel honeycomb cutting bed to fit. These can be quite costly or fairly affordable depending where you are looking. The benefit of a steel honeycomb is you can use high power magnets to hold material down.

    Click the link to add information to this solution:
    HOW CAN ENHANCE THE BLACKTOOTH?

  • WHAT SOFTWARE CAN BE USED WITH THE BLACKTOOTH LASER CUTTER?

    If you take the standard parallel cable BoB (Break Out Board), then you will need control software (Mach 3 or EMC2) and CAM software to make your G-Code (such as CamBam). Personally I use CamBam and Mach 3, they work beautifully but don't expect to turn them on and know how they work out of the box. Give yourself a few weeks to get familiar with the basics. CamBam is VERY powerful software for it's price. I'm surprised how much I keep learning on what I can do with it...I highly recommend it if you want as much control as possible.

    Mach 3 + CamBam as a bundle costs $310. EMC2 will give you a free replacement for Mach 3 and is exclusively for Linux.

    If you use the USB BoB, it will cost an extra $75 + $75 for the software. This is an all-in-one package so no need for Mach 3 or CamBam.

    For etching rasters (jpeg, bmp, tiff, non-vectors, photos), I highly recommend PicEngrave. It has been a labor of love for the past 9 years and John has done a wonderful job with it. It easily compares in quality compared to software that is in the $200-$300 range. John's software runs $40 and can be found here: http://picengrave.com/ (don't let the modest website fool you, this stuff can do amazing things). DotG and the Mach3 engrave plugin are two other options and instructions can be found on Dustans page in the gallery on buildyourcnc.com website.

    Click the link to add information to this solution:
    WHAT SOFTWARE CAN BE USED WITH THE BLACKTOOTH LASER CUTTER?

  • HOW DO I WIRE THE 4TH AXIS THAT YOU SELL. I HAVE MACH3 SOFTWARE. NO INSTRUCTIONS ON YOUR SITE

    The motor that is attached to the 4th axis is wired as follows:

    The motor should have red, green yellow and blue wires coming form the motor. The red and green are paired as one coil and the yellow and blue is paired as the other coil. You can wire the motor to a 3.0 amp driver with red to A+, green to A-, Yellow to B+ and Blue to B-

    Click the link to add information to this solution:
    HOW DO I WIRE THE 4TH AXIS THAT YOU SELL. I HAVE MACH3 SOFTWARE. NO INSTRUCTIONS ON YOUR SITE

  • Can I power the BOB w/Relay through appropriate pins and remove USB?

    We do not have designated pins for power on our BoB w/Relay, other than through the USB. We would not recommend removing the USB on our board since it may cause issues and irregularities within the board.

    Click the link to add information to this solution:
    Can I power the BOB w/Relay through appropriate pins and remove USB?

  • ok I Build my CNC machine table and now need a complete set for motor and software how you can help me

    Yes, I will need to know more specifics of the machine so I can recommend the correct electronics.

    Click the link to add information to this solution:
    ok I Build my CNC machine table and now need a complete set for motor and software how you can help me

  • I would like to use Mach3 instead of the software for my CNC router. Can you fix the electronics for me?

    Yes, you can send your electronics to us for repair, or retrofit to work with either Mach3, Mach4 or LinuxCNC. You can send us an email at customerService@buildyourcnc.com to set up your appointment.

    Some of the types of CNC electronics we will consider.

    - We will work on electronics from other manufacturers as long as you are ok with the Mach3, Mach4 or LinuxCNC control software for your CNC machine or CNC router.

    - We will repair or retrofit used CNC electronics.

    - Some customers find that electronics are overwhelming to put together so we will finish these electronics wiring and assembly for you.

    The cost for these includes labor cost for the time it takes to finish the CNC electronics repair or retrofit and for any parts that need to be replaced or added.

    Here is an example of CNC electronics that we worked on for a customer:



    This is the type of response that you can expect to receive after the CNC electronics are repaired or retrofitted to work under Mach3, Mach4 or LinuxCNC. You can see the entire work, which also shows the time involved. We also show what we were able to accomplish at the beginning of the video.

    Click the link to add information to this solution:
    I would like to use Mach3 instead of the software for my CNC router. Can you fix the electronics for me?

  • HAVE CAD FILES (.DWG AND .DWF) FOR THE GUITARS. HOW DO LOAD THEM INTO PLANT CNC SOFTWARE USE?

    You will need a cam program to create machining operations for the geometry in the .dwg file. The CAM program outputs these machining operations into g-code for the control program (planet-cnc) to use.

    I have a couple of tutorials that explain this concept.
    http://www.buildyourcnc.com/tutorials/Tutorial-sketchup-fabrication-fabricate-cad-cam-dxf

    The following is an older video but get's the point across:
    http://www.buildyourcnc.com/process1.aspx

    Additional Information:

    Click the link to add information to this solution:
    HAVE CAD FILES (.DWG AND .DWF) FOR THE GUITARS. HOW DO LOAD THEM INTO PLANT CNC SOFTWARE USE?

  • Where can I download the USBCNC software? The https://buildyourcnc.com/files/CNCUSB_20130308.zip link is dead.
  • Im having software setup problems with my backtooth (mach3) and i seem not to find a solution in the forum. what can i do?

    You can call us, send an email, or pose the specific question on this customer service live that pertains to the issue that you are having.

    Click the link to add information to this solution:
    Im having software setup problems with my backtooth (mach3) and i seem not to find a solution in the forum. what can i do?

  • I want to use Planet-CNC software can I use Mach3 USB Board

    Planet-CNC is the control software. If you decide to use the USB controller, you will need to use the planet-CNC software as the control software. You will be able to use any of the CAM software applications with the planet-CNC control software.

    Click the link to add information to this solution:
    I want to use Planet-CNC software can I use Mach3 USB Board

  • DOES ANY OF THE SOFTWARE THAT COMES WITH IT COMPATIBLE MAC 10.6?

    There are several CAD/CAM programs out there for MacOS. Here is a list of a few: http://www.macuser.de/forum/f53/3d-2d-cad-395058/#post4499316
    I've also read good things about punchCAD: http://www.punchcad.com/
    Of course, there is always SketchUp if you are in a pinch. There are a few CAM plugins for SketchUp as well, but I've never used them, so I can't vouch for them.

    CAD/CAM will get you as far as designing your parts and producing the g-code, but if you also want to run the CNC machine with your Mac, you will need a piece of software similar to Mach3 or EMC to run the g-code. I haven't been able to find anything like these programs that runs on Mac, so you may have to run Mach3 or EMC in Windows using Boot Camp or a virtual machine such as VMware or Parallels.

    Personally, I would use the Mac to do all the CAD/CAM, then use a cheap PC to run the CNC machine.

    Additional Information:


    Additional Information:
    EasyDNC for OSX
    www.dnc-x.com

    Additional Information:


    Additional Information:
    Hi guys I’m new to the cnc and I’m beginning to learn how to operate and cad-cam software also my cnc runs on Mach3 my questions is if I should use MacBook to do all designs if I can have all this software to run on Mac or I have to use windows software to operate it? I have separate small computer connected to the cnc table who have Mach3 on it please help. Also if you know any other software much easy for beginners please let me know thank you guys!
    My email if needed is r1jastrzebski@gmail.com

    Additional Information:


    Additional Information:
    Hi , thank you for your advise!

    Additional Information:
    Hi , thank you for your advise!

    Additional Information:
    Hi , thank you for your advise!

    Additional Information:
    Hi , thank you for your advise!

    Additional Information:

    Click the link to add information to this solution:
    DOES ANY OF THE SOFTWARE THAT COMES WITH IT COMPATIBLE MAC 10.6?

  • How do you remove the collet on the 2.2 kW spindle? It seems to be a part of the retaining nut.

    You'll need to twist and pull the collet while also canting it side to side until it comes free from the nut. It is not actually attached to the nut it just takes some jiggling to separate the two.

    Click the link to add information to this solution:
    How do you remove the collet on the 2.2 kW spindle? It seems to be a part of the retaining nut.

  • I had to wipe my computer due to virus and now can not download the USB software again. I get a "unhandled exception" error message. Any suggestions?

    An unhandled exception generally means that, in the program code, the program is not checking against every possible exception that could occur. Most likely, this exception is caused by some limit that is being exceeded (or the other way around). I would remove any files that could be associated with the program, like setting files, or even register configurations associated with that software. Also, make sure that you completely update your version of windows.

    Check to make sure all of the drivers are current for your graphics hardware. Make sure that your graphics hardware works in other programs as well.

    If you upgraded the Windows version, check to make sure your graphics hardware is compatible with the new version of Windows. Unhandled exception issue may be associated with graphics hardware and compatibility.

    Customer Response:
    I've given up on the wiped laptop and loaded the program on a different computer using windows 8. At first it won't operate my CNC until I read on Planet-CNC forum about loading the drivers on windows 8. All working now. Will run through the calibrations again today. Thanks

    Click the link to add information to this solution:
    I had to wipe my computer due to virus and now can not download the USB software again. I get a "unhandled exception" error message. Any suggestions?

  • How deep is the bed? As in, how far can I get the head from the base?

    Which machine are you referring to?

    Click the link to add information to this solution:
    How deep is the bed? As in, how far can I get the head from the base?

  • HOW DO I DETERMINE THE AMOUNT OF SCREW WEIGTH THAT MY MOTOR CAN HANDLE

    There are two main questions that we can answer with respect to motor torque and the mechanical advantage of lead screws, 1) What torque motor do you need to lift a particular weight, or 2) What maximum weight will my motor torque be able to lift.

    This formula uses Newtons (N) as it's final unit. Use this with the included radius (R) to determine the torque. Newtons can easily be converted to lbs or ounces using online conversions.

    Effort = Sf + (Load/(2 x pi x (R/p) x Se))

    where:
    p = pitch of the screw
    Se = screw efficiency = Standard lead screw will be between 20% (.2) and 40% (.4)
    Sf = static force. This is the force that is needed to start the movement. The number may be eliminated, but it is good to use a number in the 5 N to 20 N range.
    Load = the expected load that the effort will need to carry (i.e., the router and the included axis assembly that the motor will need to lift)
    R = radius of the lead screw


    This formula is based on the "law of the machine"

    The final effort amount with its unit of newtons and R will be the torque. For example, if the effort comes to 100 N (newtons) and the R is .5 inches, then you can assume that the effort is 50 N-in since it would take twice the effort to turn form the one inch mark from the center of the shaft.

    Example:

    Load = 90 N (20.2 lbs)
    R = 1 inch since that is the length from the center of the shaft that the motor is rated
    p = 1 inch / 13 = .08 inches

    Effort = 5 N + (90 N / (2 x 3.14 x (1 / .08) x .2))
    Effort = 5 N + (90 N / (6.28 x 12.5 x .2))
    Effort = 5 N + (90 N / (15.7))
    Effort = 5 N + (5.73 N)
    Effort = 10.7 N = 2.4 lbs = 38.4 oz-in

    I am putting the oz-in on the end because the formula considers the distance from the center of the shaft to be one inch.

    Therefore, a 425 oz-in motor would be able to lift a 20.2 lb Router with its accompanying assembly. If the assembly and router is heavier, plug in the numbers and determine the effort required.

    With a bit of algebra, the formula can be rewritten to find the load:

    Load = (Effort - Sf) x (2 x pi x (R/p) x Se)

    Another formula that does not consider friction at all:

    Effort = (Load x p) / (2 x pi x R)

    Lets see if we get similar results:

    Effort = (20 lb x .08 inches) / (2 x 3.14 x 1)
    Effort = 1.6 / 6.28 = .255 lbs = 4.08 oz-in

    The results from both formulas appear to be very small because a 13 TPI screw will have enormous mechanical advantage.

    It is evident that the first formula that does consider friction that we are loosely estimating is far more conservative than the second formula. Either way, even the most conservative formula shows that the 425 oz-in motor will handle very large weights. If you are using a lead screw with only two turns per inch, .5 inch pitch, you can determine the requirements with the first formula.

    Example for a 10 TPI 5 start (2 turns per inch) lead screw:

    Load = 90 N (20.2 lbs)
    R = 1 inch since that is the length from the center of the shaft that the motor is rated
    p = 1 inch / 2 = .5 inches

    Effort = 5 N + (90 N / (2 x 3.14 x (1 / .5) x .2))
    Effort = 5 N + (90 N / (6.28 x 2 x .2))
    Effort = 5 N + (90 N / (2.512))
    Effort = 5 N + (35.83 N)
    Effort = 40.828 N = 9.18 lbs = 146.88 oz-in

    Customer Response:
    thank you so much

    Additional Information:


    Additional Information:


    Additional Information:
    how do i calculate torque of stepper motor if lead screw coupled to motor shaft and load applied by lead screw on plate is 100 kg by vertically

    Additional Information:
    Pls


    Additional Information:
    1m 16mmdiameter ball screws calculations


    Additional Information:
    What is the max load that 2 NEMA 17 stepper motors (spaced 2 feet apart, both will be pushing up on the same gantry) can lift while using a rod with the following specifications T8 OD 8mm Pitch 2mm Lead 4mm for each motor.

    Click the link to add information to this solution:
    HOW DO I DETERMINE THE AMOUNT OF SCREW WEIGTH THAT MY MOTOR CAN HANDLE

Get Help with:
This Product
Orders
Tech Support
Sales
This Product
Order Query
Tech Support
Sales
Not logged in. Log In Register
Track Order(s)
View Order(s)
I Want to Schecule a One-On-One Paid Tech Support Session
Book an Appointment Pertaining to a BuildYourCNC Product (Free)
Ask a Quesion Below (Free):
Book an Appointment Pertaining Other Equipment ($60/half hour)
Book an Immedite Appointment Pertaining Other Equipment ($120/half hour)
Ask a Quesion Below (Free):
Waiting for response... I may not answer immediately, but I was notified on my cellular phone so my response is forthcoming. If I don't respond immediately, you can always go to the [My Account] page to see all of our chats at any time.