The 12V power supply has 3 terminals for AC in: N, L and earth ground. The output of the 12V power supply has 2 DC + and - terminals. Cut the connectors off of the ends of the fan and pump wires. Strip the red and black wires of both units. The fan will connect to the 12V power supply red to the + and black to the -. The pump will connect in the same way, but the white is not connected.

If you have a pump that has a grey and black wire on the large connector, the grey is the 12VDC V+ wire and the black wire goes to the V-. The extra wire does not need to be connected.

Click the link to add information to this solution:
I bought a gantry mounted spindle water cooler kit. I cut off the plug terminal on the end. There are three wires and it is labeled as a 12 V DC motor. How do I wire it to the power supply? No combination of connections seems to work. the fan runs fine. it

The 12V power supply has 3 terminals for AC in: N, L and earth ground. The output of the 12V power supply has 2 DC + and - terminals. Cut the connectors off of the ends of the fan and pump wires. Strip the red and black wires of both units. The fan will connect to the 12V power supply red to the + and black to the -. The pump will connect in the same way, but the white is not connected.

If you have a pump that has a grey and black wire on the large connector, the grey is the 12VDC V+ wire and the black wire goes to the V-. The extra wire does not need to be connected.

Click the link to add information to this solution:
I bought a gantry mounted spindle water cooler kit. I cut off the plug terminal on the end. There are three wires and it is labeled as a 12 V DC motor. How do I wire it to the power supply? No combination of connections seems to work. the fan runs fine. it

Here are links to the sole pump and heat exchanger/fan. I am sending you amazon links sine I don't ahve listings of my pump and heat exchanger separately from my cooling system:
Pump: https://amzn.to/3R6zPbj
Fan/radiator (Heat exchanger): https://amzn.to/3UWOuqN

Click the link to add information to this solution:
I RECENTLY PURCHASED A REPALCEMENT 12V DC SWITCHING POWER SUPPLY, HOOKED IT UP BUR DID NOT THE PUMP AND RADIATOR. VERIFIED OUTPUT OF UNIT AT 12V. SO I'M ASSUMING ALSO NEED TO REPLACE CAN YOU SUPPLY ME LINK PURCHASE THEM?

When wiring the limit switches to our BoB(breakout board), depending in the older model or our revised version (https://www.buildyourcnc.com/item/electronicsAndMotors-parallel-breakout-relay#prettyPhoto/0/), the older version will need the COM (limit switch) connected to 5V and the NO/NC to your input pin, but with our newer version you will use GND(ground instead of 5V) to common and the same for NO/NC but the setup in the mach3/confi/ports&pins/ is still the same.

Here is a tutorial where you can see how to set up the limit switches correctly (with our older parallel BoB): Part 1:(

Click the link to add information to this solution:
I am attempting to set up limit switches on the 5 axis parallel breakout board that came with my BlackFoot kit. The output pins are driving the motors perfectly, but I can't figure out the input pins. With one lead in the 5V pin and one lead testing the input pins, my multimeter reads 0V for all of the input pins. Shouldn't those circuits be +5V? Where am I going wrong?

Here are links to the sole pump and heat exchanger/fan. I am sending you amazon links sine I don't ahve listings of my pump and heat exchanger separately from my cooling system:
Pump: https://amzn.to/3R6zPbj
Fan/radiator (Heat exchanger): https://amzn.to/3UWOuqN

Click the link to add information to this solution:
I recently purchased a repalcement 12v DC Switching Power Supply, I hooked it up bur it did not power up the Pump and radiator. I verified the output of the unit at 12v. So I'm assuming I also need to replace the pump and the radiator. Can you supply me a link to purchase them?

Red is A+
Blue is A-
Black is B+
and Green is B-

Click the link to add information to this solution:
I purchased the 3 Axis Heavy Gantry Electronics /w Pokeys57CNC controller and the motors supplied only have 4 wires coming out of them (R,G,B,Blk). Your wiring video shows wiring 8 cables. do you have a video showing how to wire the 4 wire version?

The Mach3 USB controller requires a minimum of 12V and a maximum of 24V to the DCM and 24V terminals. The DCM is the GND or DC negative terminal, and the 24V terminal is the positive terminal.

Click the link to add information to this solution:
I bought the Mach3 board and am trying to connect it with an AMB 1400 DI router, which has a normal power supply (1400W) as well as a digital interface which has three wires: a brown wire (10-26V, power supply), a white wire (ground) and a green wire (0-10V signal). I'm no electronics guy--how do I connect the digital interface of the AMB to the Mach3 board?

The 12V power supply has 3 terminals for AC in: N, L and earth ground. The output of the 12V power supply has 2 DC + and - terminals. Cut the connectors off of the ends of the fan and pump wires. Strip the red and black wires of both units. The fan will connect to the 12V power supply red to the + and black to the -. The pump will connect in the same way, but the white is not connected.

If you have a pump that has a grey and black wire on the large connector, the grey is the 12VDC V+ wire and the black wire goes to the V-. The extra wire does not need to be connected.

Click the link to add information to this solution:
I purchased the spindle cooling kit with power supply. and was wondering if you have a diagram on installing or a video. thank you

Hey, sorry I just found the wiring diagram and see that #4 is disabled. My bad. Thanks.

Click the link to add information to this solution:
I just purchased some wire for my 2.2 spindle as per your recommendation it's 14 AWG stranded wire for the VFD to Spindle (U, V, W) connections. However, it's a three wire (black, white and Ground). Which numbers on the female pin connector do I connect the wires to. Cheers.

The 12V power supply has 3 terminals for AC in: N, L and earth ground. The output of the 12V power supply has 2 DC + and - terminals. Cut the connectors off of the ends of the fan and pump wires. Strip the red and black wires of both units. The fan will connect to the 12V power supply red to the + and black to the -. The pump will connect in the same way, but the white is not connected.

If you have a pump that has a grey and black wire on the large connector, the grey is the 12VDC V+ wire and the black wire goes to the V-. The extra wire does not need to be connected.

Click the link to add information to this solution:
The gantry mounted spindle water cooler pump that I purchased does not operate no matter how I connect the three wires to the two wire power supply.

The blackTooth laser power supply will use 4 - #8 x 1" screws, and 4 - #8 nuts. As stated on step 10 here (https://buildyourcnc.com/blackToothLaserCutterAndEngraver.aspx#prettyPhoto/10/)

Click the link to add information to this solution:
I am building a blacktooth. I don't see in the instructions what screws are meant to fasten the power supply to the wood. The instructions show how to wire it but I don't see where it says which screws to use. I don't want to guess and end up being short later. Thanks. .

All you need is a CNC controller like the following options:

https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach3-USB-Board

This controller is easy to connect using standard wire screw terminals and works with the mach3 control software.

https://www.buildyourcnc.com/item/electronicsAndMotors-electronic-component-breakout-Mach4-mach3-USB-ethernet-Board

This controller is a little bit more difficult to connect, but is a more feature-rich controller and will work with both mach3 and mach4 CNC control software titles.

Specifically, a CNC controller connects to the computer via a USB cable and connects to the motor drivers. These controllers also connect to the limit switches, spindle/router control, air/fluid/mist control, etc.

Click the link to add information to this solution:
Hello there, I am a beginner in trying to control a stepper with a pc, you can sell me a kit to control my motor from the pc. I already have a motor, driver, and power supply

Do you have an oscilloscope? You will be able to see the PWM signal and determine if the output is correct. Make sure that you are using the 10V from the VFD as the voltage reference for the 10V terminal on the Mach3 USB controller. The 10V terminal is an input, not an output on the Mach3 USB controller. The 10V is the top voltage signal level that the Mach3 USB controller uses for the PWM signals 100% duty cycle.

Click the link to add information to this solution:
[575] I have the wiring and programming and parameters set the same way that you do in the spindle speed control and outputs videos, I can start and stop the spindle with mach3 but can't seem to control the speed. Can you think of solutions?

The 12V power supply has 3 terminals for AC in: N, L and earth ground. The output of the 12V power supply has 2 DC + and - terminals. Cut the connectors off of the ends of the fan and pump wires. Strip the red and black wires of both units. The fan will connect to the 12V power supply red to the + and black to the -. The pump will connect in the same way, but the white is not connected.

If you have a pump that has a grey and black wire on the large connector, the grey is the 12VDC V+ wire and the black wire goes to the V-. The extra wire does not need to be connected.

Click the link to add information to this solution:
THE GANTRY MOUNTED SPINDLE WATER COOLER PUMP THAT I PURCHASED DOES NOT OPERATE NO MATTER HOW CONNECT THREE WIRES TO TWO WIRE POWER SUPPLY.

https://buildyourcnc.com/Item/electronicsAndMotors-electronic-component-e-stop-button-switch-safety#prettyPhoto/0/

Click the link to add information to this solution:
How do I wire up multiple E-stop to breakout board, does each E-stop need there own pin? If not since there are only 4 screws on stop 2 for no and 2 for nc do you just splice the wires together if your only using 1 pin? Thanks

Yes. The VFD (Variable Frequency Drive) has a large set of parameters that can be modified. This is typically called "programming" the VFD. The parameters can be accessed using the front control panel of the VFD.

Since the VFD is the mechanism that control the allowable current draw from the spindle, there is a parameter that assigns the motor rated current; however, it is probably better to match the rated current of the motor and "up" the circuit breaker current instead. If the current limit is set too low, then there is a possibility that the spindle will cause a current overload error on the VFD and cause the spindle to stop.

Click the link to add information to this solution:
With your 120v drive systems for your 2.2kw spindles, do you do something to limit the output to the spindle so that the current draw doesn't exceed the 80% limitations of a 20a circuit? I have a dedicated circuit for my router and I am considering a spindle upgrade, but I am curious how the configuration matches the math.

You will need to look for the parameter that controls the run frequency. The frequency can be controlled bu the panel, external terminals, or the RS485 TX/RX terminals (UART protocol). You will want to change that parameter so it uses the panel. If you are referring to the maximum panel dial frequency is only allowing 200-300 rpm, then look for the parameters to control the frequency.

For 200 RPM:
Hz = 200/60 = 3.33 Hz

For 300 RPM:
Hz = 300/60 = 5 Hz

Conversion to RPM:
If you ever find yourself yearning to reverse-engineer the process, the formula is as follows:

RPM = Hz × 60

Look for values that match somewhere between 3 and 5 in your frequency parameters and replace them with 400 to give you 24,000 RPM max.

Click the link to add information to this solution:
[77] Hello. I’m interested in buying a water cooled spindle and VFD. I have an Avid Pro CNC and would love to control it using Mach 4 but I keep hearing it’s difficult to integrate. Also, is the water pump 120 or 240? I’d love any advice etc. eBay is a web of confusion with all of the options. Thank you.

Here is how to connect your router to the parallel breakout board through the on-board relay. You will need a spare extension cord. You will need to remove a portion of the outer jacket of the extension cord to expose the white, black and green wires (white = neutral, black = live and green = ground), understanding that the neutral and live create the completed circuit.

See this image of a similar connection. The terminal has the same connections.
https://www.buildyourcnc.com/images/vacuum-pressure-controller-relay-terminals-700.JPG

Image of the relay terminal:
https://www.buildyourcnc.com/images/breakoutboardrelayNONC.PNG

The live/black wire would be cut and one end of the cut would be secured into the P terminal and the other cut end would be secured into the S terminal. The live and ground wire would be uncut and travel from the plug to the router.


Additional Information:
You can also connect other high powered devices to the breakout board using any of the output terminals. You will need to supply extra relays like the one shown here:
https://www.buildyourcnc.com/item/electronicsAndMotors-breakout-Relays-relay-board-250V-12A-5V

Or you can find SSRs (Solid State Relays) that will accept 5v to drive the relay coil. Make sure the SSR will protect the 5V line from Back EMF as there is a coil in the relay. The one we sell contains a fly-back diode to protect the 5v terminal.

Click the link to add information to this solution:
I have your breakout board with relay parallel port , I have a vacuum, light on router and air pump I want to also hook up to board, can I hook those up to board and also could I had reylays to each one, what is the best way to figure this out any information would be great. Thanks

If the sensors are NC (normally closed) you can wire them in series. If the sensors are NO (Normally Open) you can still wire them to the same input, but the wiring needs to be in parallel (like a ladder). I have more information on the following video:

Click the link to add information to this solution:
[788] Thanks for the oportunity to ask, I am building a cnc and using npn closed sensors could you help me with the conection of these, do i still connect them in series if i use more than two in each axis. Also you mention that a stop switch should be connected grd and input to the controller would that be done after the 24v power supply. Thanks r