I need programing help not wiring help. Speed will only go to 50.

You can find the inverter (VFD) manual at: https://buildyourcnc.com/Documents/HuanYang_inverter_manual.pdf

If you have further questions, please enter your question here by submitting additional information.

Click the link to add information to this solution:
I called a little bit ago for a copy of the inverter manual. I really need this infor. thank you

If you need technical support for the 220V VFD, you can ask the specific question on the customer service section of the website. Link below:
https://buildyourcnc.com/CustomerService.aspx

Click the link to add information to this solution:
Do you know of any technical support for the 220 Volt VFD you sell? I can't find any help on it.

The spindle does not come with a manual, however the inverter should come with a manual booklet in the box. The wiring diagram and PD settings for the inverter and spindle (https://www.buildyourcnc.com/item/spindle-inverter-2!2kw-spindle-novfd) can be view together on the spindle page, also you can use a local hardware store extension cord (orange) to connect/wire from your outlet(220V) to your inverter and spindle accordingly from the diagram.

Additional Information:
I also received a spindle and inverter without a manual. While the diagrams on the product page were sufficient to get the unit running, there is no documentation anywhere to be found concerning the terminal block that is used for external control. What does one have to do to get a hold of the manual that was supposed to come with the inverter? Manuals for the 220VAC model are plentiful online; however, manuals for the 110VAC model are non-existent.

Click the link to add information to this solution:
Transaction EQEPB4915043, My 2.2Kw Spindle and Inverter showed up without any manual or instructions. Can you provide a manual? Thank you

The wire that we sell for the limit switch wiring is here: https://www.buildyourcnc.com/item/3d-printer-component-cnc-electronicsandmotors-cable-wire-3-conductor-22-awg-wrcon-cablewire3conductor22awg

This is shielded cable to make sure there isn't any external interference with sensitive components and long wires associated with limit switches. This is necessary due to the interference caused by the motors on a CNC router and the milling process.

Additional Information:
So unshielded is cool. That's what I was curious about. Cheers.

Additional Information:
Absolutely. It's really the only type of cable I would recommend for connecting limit switches.

Click the link to add information to this solution:
Do you sell 22 to 24 AWG stranded and shielded for wiring of the limit switches and E_Stop?

Spindles are generally covered up to 1 year after date of purchase. We do not repair them in house, but we do work with our manufacturer to replace defective units. Generally if you have a defective unit covered under warranty, we will issue a replacement.

Click the link to add information to this solution:
what is the warranty period and do you repair these in house? 2.2 kW (kilowatt) Water Cooled Spindle with Inverter (VFD)

The use of the hex inverter in the application to invert a direction signal to have a motor run in the reverse directions is relatively simple.

First, go to this link and look at the chip diagram:
https://www.buildyourcnc.com/item/electronicsAndMotors-hex-inverter-breakout-newbiehack-integrated_circuits-hex-inverter

Connect 5V from the USB interface tothe VCC pin. The pin on the keyboard jog header can be used. Connect the GND pin from the USB interface to the GND pin on the hex inverter. Connect the CW terminal from the USB interface to the 1A pin on the hex inverter. Connect the 1Y pin from the hex inverter to the driver.

Additional Information:
I got a question??? I am a dummy when it comes to cnc. I got 6040 1500kw water cold engraver 3 axis from china. I can not get anything out of them pertaining help they keep telling me the same thing over and over and over and I'm doing it and send them pictures that I know. Anyway email me a wiring diagram for the PRT 1500 watt spindle motor control box and has the emergency stop on and off switch manual PC and of course yhe screanm fultonsbusiness@gmail.com

Additional Information:
I got a question??? I am a dummy when it comes to cnc. I got 6040 1500kw water cold engraver 3 axis from china. I can not get anything out of them pertaining help they keep telling me the same thing over and over and over and I'm doing it and send them pictures that I know. Anyway email me a wiring diagram for the PRT 1500 watt spindle motor control box and has the emergency stop on and off switch manual PC and of course yhe screanm fultonsbusiness@gmail.com

Click the link to add information to this solution:
Is there a wiring diagram for hooking up your hex inverter between your USB breakout board and the controller?

For our machines our steps for the build process can be found on the actual machine page with images to reference (please read carefully all the instructions) (https://www.buildyourcnc.com/blackToothLaserCutterAndEngraver.aspx).
You can get further help here (http://blacktoothlaser.blogspot.ca/2013/04/index-for-blacktooth-laser.html?view=sidebar) a post made by one of our customers!

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
where is the build manual for the blacktooth laser? online? I didnt get one with my machine

Please refer to the Spindle wiring diagram found on the product page for the 2.2KW spindle. The wiring diagram will be the same for the 1.5kW Spindle. The only difference will depend on if you are using 110v or 220v power, as setting PD008 asks you to specify the max voltage.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
please send wiring diagram for the 1500kw spindle and inverter combo. i need to see what additional things need be purchased. thanks.

No. Horsepower is a measure of the rate at which a device can do work, as is the Watt. The conversion ratio is about 746 Watts = 1 Horsepower. Therefore your 5hp motor is equivalent to about 3,730 Watts. The kW designates kilowatts, or units of 1,000 Watts. So a 1.5kW inverter can supply only 1,500 Watts. Our larger inverter supplies 2.2kW, but you need a minimum of 3.7kW for your application.

Click the link to add information to this solution:
I have a 5hp 3600 rpm 3phs spindle motor will your inverter work for this application 1.5kw?

There is a button on the front of the VFD that will cycle through RPM, Freq, and a few other readings. If there is a >> button on your VFD, that will work. If there is a mode button on your VFD, that should works as well.

Additional Information:
There is a >> disc button but it does not cycle through the display modes.

Additional Information:
Is there a parameter setting to make this button work to cycle thru the display modes?

Additional Information:
setting the starting rpm

Additional Information:
the vfd will not start the motor

Additional Information:
Any progress on this? I have the same issue.

Additional Information:
What model is your VFD?

Additional Information:
Mine is a YL620-G-5.5Kw

Additional Information:
That model will not be able to show RPM. You will be able to show the frequency, which can be used to determine the RPM. RPM equals the Frequency x 60.

Additional Information:
There is an Icon for RPM at the top of the display I cannot cycle through the different options to see the RPM

Additional Information:
At the top of my control panel is has 6 different lights which indicate what your seeing. in order from left to right they are COM, ALM, DISP, RUN, Hz, RPM I have seen the ALM light up on initial set up but that was fixes with a parameter change. The run light shows up when i turn the spindle on and and it is running. I am however not able to get any of the other lights to show or to get the RPMs to display

Additional Information:
If you do see an RPM light on the display, that panel sticker may be a sticker used for many types of VFDs and the RPM is not used. There is parameter: P00.24 which allows you to pick what to display. The choices a
re:
0: Display current target frequency. This will display your knobs, potentiometer, setting, not the actual spindle frequency.
1: Display electric machinery run frequency. This will display the actual frequency that the VFD is currently sending to the spindle.
2: Display electric machinery run current: this will display the current the spindle is currently drawing.
3: Display input AC voltage. Self explanatory.
4: Display mother line voltage. This will display the actual voltage at the input.
5: Display output voltage. This will display the voltage at the UVW terminals for the spindle.
6: Display speed paragraph number SPx. I believe this displays which frequency is being selected (P07.00 to P07.07, or 1 to 8 respectively).
7: Display inverter temperature. This is the temp of the VFD, self explanatory.
8: Display input signal X1-X3/output signal. This simply shows the inputs/outputs associated with the external terminals.
9: Display user variable. This one I have not delved into, so it may be something to look into.
10: Display user count value. Same, this one could be useful.
11: Display temporary debugging variable. Haven't tried this one, so I can't inform of any useful information but it won't pertain to this subject anyway.
12: Display automatic multisegment run step and time. I haven't delved into this one either, but it won't show RPM.

Click the link to add information to this solution:
How to display RPM instead of frequency on the VFD? I have the 2.2kv 110 volt spindle and inverter.

I would recommend creating a post in our forums page (buildyourtools.com), and ask any specific questions there! Since there might be someone willing to help you locally!

Since we cannot disclose any customers contact information, without there permission! Going through the forums will be the best idea to be able to find someone locally, with one of our machines!

Also you can contact us directly at customerservice@buildyourcnc.com

Click the link to add information to this solution:
Do you have customers/builders in the Netherlands who I can ask for help or assistance?

We don't have cad models of the HIWIN blocks, but you can find the models on McMaster.com. They have can drawings and models for most of these types of parts.

Click the link to add information to this solution:
DO YOU HAVE CAD AVAILABLE FOR THE HIWIN GUIDE BLOCKS SELL AND RAIL?

We don't have cad models of the HIWIN blocks, but you can find the models on McMaster.com. They have can drawings and models for most of these types of parts.

Click the link to add information to this solution:
DO YOU HAVE CAD AVAILABLE FOR THE HIWIN GUIDE BLOCKS SELL AND RAIL?

We sell HIWIN rail and Linear guide rail by the inch (cut to size) as well as the blocks individually.

Click the link to add information to this solution:
I need a guide rail 15mm X 100mm yours is 2000mm or 2 meter, do we cut the rail to size? do you sell the block separetly?

If you purchased a machine that was used and you don't know which mode it is, you can browse our models here:
https://www.buildyourcnc.com/Item/milling

Click the link to add information to this solution:
I bought an used machine that need work how can I find the model. The owner said, he used this site for parts and manual.

Yes, it is found in laser components section

Click the link to add information to this solution:
DO YOU GUYS SELL THE POTENTIOMETER FOR YOUR LASER SYSTEM BY ITSELF

Yes, I was intending to design a medium sized laser cutter and engraver but the project was put on hold. I will start the design in a few weeks (around mid Dec 2017).

Additional Information:
Do you think you would want a horizontal machine, or a slanted, more vertically oriented machine?

Additional Information:
For the work I plan to do, I would need a horizontal bed. I will be doing some work with cutting small pieces and can not afford to have any drop during a raster or another vector cut.

Additional Information:
Ok. Thanks.

Click the link to add information to this solution:
Can you design and sell a laser that is medium sized? The Black Tooth is too small and the XL is too big. I need about 36" x 24" cutting space minimum. 60x40 is ideal.

I just looked at your account and noticed that your shipments has not been made yet. I will talk to the shipper tomorrow morning when the office opens determine what happened. My apologies for this.

Click the link to add information to this solution:
I ordered a 1.5kW Spindle and Inverter (110 Volt) on December 18th and have heard nothing since. I notice you did charge my credit card for the purchase. Please update me with an ETA as soon as possible.

Our spindles have a runout of less than .0001 in, which includes that collets that we sell. If you use a collet from another manufacturer, we cannot guarantee this TIR (Total Indicated Runout) dimension.

Additional Information:



Additional Information:



Additional Information:

Click the link to add information to this solution:
Hi, I'm interested in the 1.5 kW (kilowatt) Water Cooled Spindle with Inverter (VFD), I would like to know about the run out of this spindle?