Shipping crate 121" X 36" X 92"

Weight 511 LBS

Additional Information:
ship in india pls

Additional Information:
International shipping rates can be determined by:
- adding products to the cart
- go to the cart and enter shipped by address
- and pressing the calculate shipping button

Click the link to add information to this solution:
WHAT IS THE SHIPPING WEIGHT AND DIMENSIONS FOR GREENLEAN?

Shipping crate size 121" X 36" X 92"

Weight 511 LBS

Click the link to add information to this solution:
WHAT IS SHIPPING DIMENSIONS AND WEIGHT FOR THE VERTICAL LASER.

Shipping crate size 121" X 36" X 92"

Weight 511 LBS

Click the link to add information to this solution:
WHAT ARE THE SHIPPING DIMENSIONS FOR VERTICAL LASER

76" X 40" X 26"
230 LBS

Click the link to add information to this solution:
WHAT ARE THE SHIPPING DIMENSIONS FOR GREENBULL?

The blacktooth ships in 3 boxes.

Structure 38x22x5 #54

Components 14x13x13 #30

Laser Tube 35x7x6 #4

Click the link to add information to this solution:
WHAT ARE THE BLACKTOOTH SHIPPING DIMENSIONS?

Actual table dimension: 4'x8' is 56.078"x 121.50" (the overhang in the illustrations should be 3/4" thick)
To determine the frame dimensions, first consider using the frame height shown of almost 3' (2.86'). The width of the frame should be 4" narrower than the dimension from rail edge to rail edge (6X rail to rail is 80.078"). This will provide a 2" overhang on both sides (4X frame width should be 56.078").
The length of the frame should be 4" shorter than the desired length of the rails to provide a 2" overhang on both ends. The travel length will be 20" shorter than the rail length due to the space occupied by the gantry sides.
Two long pieces of 3/4" material will need to be placed on top of the frame with the 2" overhang on the sides and the end. These long strips of material will receive the rails and the chain mounts on the ends.


Link:
https://www.buildyourcnc.com/Item/cnc-machine-greenBull-v4-4X

Click the link to add information to this solution:
WHAT ARE THE DIMENSIONS FOR GREENBULL TABLE?

A standard 40W CO2 laser will cut up to 1/4" thick of material, be it wood, acrylic, card stock, leather, fabric, foam, cork, etc. (Decent speed and final cut are heavily dependent on a strong air assist upgrade)

Metals cannot be cut due to the power level and wavelength of the CO2 laser. But it can be marked with special solutions like Cermark or Thermark.

Click the link to add information to this solution:
WHAT THICKNESS OF MATERIAL CAN THE BLACKTOOTH LASER CUT?

You can expect a two week lead time for the redFrog pick and place machine.

Additional Information:

Click the link to add information to this solution:
WHAT IS THE LEAD TIME FOR REDFROG PICK AND PLACE MACHINE?

Standard Version Features Mach3 Mach4 Hobby Mach4 Industrial
Number of Planners 1 1 1
Number of Axis 6 6 6
Out of Band Axis (OBA) 0 1 6
Slave axis (uses up coordinated axes) 3 N/A N/A
Slave motors (does not use up coordinated axes) N/A 4 per Axis 4 per Axis
API Interface - Open to All Hardware Yes Yes Yes
Extended Plugin Support Yes Yes Yes
User customizable GUI Yes Yes Yes
Unified (GUI) Interface - PLC, CNC, etc.. Yes Yes
Unlimited IO Yes Yes Yes
Modbus PLC Yes Yes Yes
PMC (Ladder Logic addressing for cnc/plc) Yes Yes
Unlimited File Size Yes Yes
Tool Path Display Yes Yes Yes
Tool Path Speed & Quality Low High High
Scripting - Customization Yes Yes Yes
LUA Scripting - simple, fast, cross-platform Yes Yes
- Lua sockets (ftp, http, smtp,..) Yes Yes
- SSL (security layer) Yes Yes
- LFS (manage large files and data storage) Yes Yes
- Seriel port Yes Yes
- Enraving of part numbers / serial numbering of parts Yes Yes
- Plugin panel objects Yes Yes
IPC Library for Data Sharing/tracking (Interprocess communication) Yes Yes
Full Feature Screens/Controls Per Machine Type Yes Yes
Currently Availabe: Mill, Router, Lathe, 3d Printer Yes Yes
Multiple gcode Interpruters (Per Machine Type) Yes Yes
Probing - Intergrated in standard screens Yes Yes
Simulated 3d Machining (with additional plugin license) Yes Yes
Tool Life Management (G10 L3 command) Yes
Screw Mapping Yes
Professional Screen Designer (advanced G.U.I.) Yes
- Screen Animation Control Yes
- Screen Integrated Tool Table Control Yes
- Screen Integrated Work Offset Control Yes
- Screen Integrated gcode editor Yes
- Screen Artsoft Wizard Package Integration Yes
Macro B gcode Programming (#variables) Yes
- User definable gcodes via marco calls Yes
- Macro Calls: G65, G66, G66.1 Yes
- gcode via marco call (custom G codes via macro B) Yes
- mcode via macro call (custom M codes via macro B) Yes
- mcode via sub code (custom M code via sup program) Yes
- Conditional gcodes Yes
- set VN call - define variable names Yes
gcode Editor Included Yes
Scripted M code (custom M code via LUA script) Yes Yes
Variable Speed Spindle Yes Yes Yes
Spindle Relay Yes Yes Yes
Coolant relay Yes Yes Yes
Mist Relay Yes Yes Yes
Threading Yes Yes Yes
Rigid Tapping Yes Yes Yes
Single Block Yes Yes Yes
Block Delete Yes Yes Yes
Optional Stop Yes Yes Yes
MACH CNC CONTROL SOFTWARE MAIN FEATURES AND VERSION DIFFERENCES
Standard Version Features Mach3 Mach4 Hobby Mach4 Industrial
MACH CNC CONTROL SOFTWARE MAIN FEATURES AND VERSION DIFFERENCES
Cutter Comp Yes Yes Yes
Fanuc Type C Cutter Comp Yes Yes
Fixture Offsets Yes Yes Yes
G51 Scaling Yes Yes Yes
G92 Offsets Yes Yes Yes
G52 Offsets Yes Yes Yes
Event Driven Yes Yes
Multi Line MDI Yes Yes
Subs In MDI Yes Yes
OpenGL Optimization Yes Yes
Multi-platform OS Compatibility Option Yes Yes
Online Support Yes Yes Yes
Phone Support Option Available Yes
Support Priority Yes
Available to End Users as "Do-it-yourself" Yes Yes
Summary - Mach3 versus Mach4 :
Mach4 Hobby is the closest comparable version to Mach3, yet it is still much more advanced. The price point of these versions is nearly
identical. Mach3 is very popular for hobby enthusiest and is used in highly modified form by some great OEM's. In general, Mach4 is more
complex than Mach3 and follows cnc industry standards. Mach3 has many customizations to make it easier for hobby users, but can lead to
difficulties if users plan to apply their knowledge to more advanced systems. Mach4 is built as a full featured cnc controller capable of high
speed machining for servo and stepper systems. Mach3's feature set is complete, while Mach4's will continue to expand. If you are new to cnc,
Artsoft highly recommends using and learning Mach4 even if it appears that Mach3's feature set will be adequate for your needs.

Click the link to add information to this solution:
WHAT IS THE DIFFERENCE BETWEEN MACH3 AND MACH4?

Depth of Field. This is how far the focal point goes before re-expanding again. With a 2" lens, you have approximately 2-3mm of DOF. This means that you'll have 2-3mm of perfectly focused laser before it starts to re-expand again. If you have a 4" lens, you will have up to 7mm of DOF.

Additional Information:

Click the link to add information to this solution:
WHAT IS D.O.F OR DEPTH OF FIELD FOR THE BLACKTOOTH LASER AND LENS?

The parallel (printer cable) port is uses the computer as its main source of pulse trains to operate the motor driver directly. Parallel ports are a direct connection from the processor commonly referred to as GPIO pins (General Purpose I/O pins) and provides a convenient and powerful way to interface with the computer. The parallel breakout board is included in those kits only to condition those signals for use with the drivers.

The USB serves at the actual controller, sending the pulse trains, but the computer sends simple human readable instructions to the USB controller to tell the controller how to send pulses.

The non-technical differences that may serve as the most important information to you is that the parallel configurations allow for a wider variety of industry standard software that can be used to control the cnc machine. The USB that we offer requires the operator to use a software called Planet-CNC software which is a very well made and feature full cnc control software.

Additional Information:


Additional Information:


Additional Information:
USB Motion controller breakout board work with planet cnc software?

Click the link to add information to this solution:
WHAT IS THE DIFFERENCE BETWEEN A PRINTER CABLE PORT AND USB MOTOR KITS

You can expect a two week lead time for the redFrog pick and place machine.

Additional Information:

Click the link to add information to this solution:
WHAT IS THE PICK AND PLACE LEAD TIME?

The parallel (printer cable) port is uses the computer as its main source of pulse trains to operate the motor driver directly. Parallel ports are a direct connection from the processor commonly referred to as GPIO pins (General Purpose I/O pins) and provides a convenient and powerful way to interface with the computer. The parallel breakout board is included in those kits only to condition those signals for use with the drivers.

The USB serves at the actual controller, sending the pulse trains, but the computer sends simple human readable instructions to the USB controller to tell the controller how to send pulses.

The non-technical differences that may serve as the most important information to you is that the parallel configurations allow for a wider variety of industry standard software that can be used to control the cnc machine. The USB that we offer requires the operator to use a software called Planet-CNC software which is a very well made and feature full cnc control software.

Additional Information:


Additional Information:


Additional Information:
USB Motion controller breakout board work with planet cnc software?

Click the link to add information to this solution:
WHAT IS THE DIFFERENCE BETWEEN PARALLEL AND USB ELECTRONICS COMBOS MOTOR KITS

Yes, it is ok if the thickness is plus or minus +/- about 2mm.

Additional Information:



Additional Information:

Click the link to add information to this solution:
THICKER MATERIAL OK TO BUILD THE MACHINE?

The greenBull 4X comes with all of the components and electronics to assemble the gantry of the machine. You will need to build the table. We provide the rails and roller chain for the X-axis (along the length of the table for full 8 feet of travel). You will need to provide some wire to connect the electronics and a computer to run the machine. You will also need to purchase the software that you will need to run the machine that matches how you will apply the machine. We suggest the mach3 control program. The CAM program is up to you as there are many options out there.

Click the link to add information to this solution:
WHAT DOES THE GREENBULL KIT INCLUDE AND DO I NEED TO INCLUDE?

3 axis machines cannot create undercuts in the part.

These videos show the capabilities of 3 and 5 axis machining:

3-axis CNC:

Click the link to add information to this solution:
WHAT THE DIFFERENCE BETWEEN 3 AXIS AND 5 CNC?

the package sizes will be listed in your shopping cart, in the item detail. The site will also fully calculate shipping charges directly from the carrier, for each package you purchase.

Additional Information:

Click the link to add information to this solution:
AND WHAT SIZES ARE THE PACKAGES OF MACHINE.

The lens is 20mm wide and a 50.6mm focal length (the one included). This lens will stand up to at least 30PSI air assist.

The mirrors are 25mm wide mirrors.

Focal length is the distance from the lens to the material for the laser converge into the best focal point. If a lens is listed as 2". You measure 2" from the lens to the material, this will be the tightest point the laser can go before it starts to re-expand again losing focus.

Click the link to add information to this solution:
WHAT ARE THE BLACKTOOTH LENS SIZES AND FOCAL LENGTH SPECIFICATIONS?

The password is: 608

Click the link to add information to this solution:
WHAT IS THE SYSTEM PASSWORD FOR LASER CONTROL UNIT?